Instruction manual

ManualsBrandsDeWalt ManualsPower ScrewdriverDW258-XE

DW251-XE, DW252-XE, DW252WT-XE, DW255-XE, DW256-XE, DW257-XE, DW258-XE,

DW260-XE, DW262-XE, DW263-XE, DW265-XE, DW266-XE, DW266-220-XE, DW267-XE,

DW268-XE, DW268G -XE, DW268-220-XE, DW269-XE, DW272-XE, DW272W-XE,

DW272WT-XE, DW274-XE, DW274W-XE, DW274-220-XE, DW276-XE, DW276-220-XE,

DW281-XE, DW282-XE, DW284-XE

SCREWDRIVERS

INSTRUCTION MANUAL

Summary of content (12 pages)

PAGE 1
INSTRUCTION MANUAL DW251-XE, DW252-XE, DW252WT-XE, DW255-XE, DW256-XE, DW257-XE, DW258-XE, DW260-XE, DW262-XE, DW263-XE, DW265-XE, DW266-XE, DW266-220-XE, DW267-XE, DW268-XE, DW268G-XE, DW268-220-XE, DW269-XE, DW272-XE, DW272W-XE, DW272WT-XE, DW274-XE, DW274W-XE, DW274-220-XE, DW276-XE, DW276-220-XE, DW281-XE, DW282-XE, DW284-XE SCREWDRIVERS
PAGE 2
PAGE 3
1. WORK AREA a. Keep work area clean and well lit. Cluttered and dark areas invite accidents. b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2. ELECTRICAL SAFETY a. Power tool plugs must match the outlet. Never modify the plug in any way.
PAGE 4
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g.
PAGE 5
Additional Safety Instructions WARNING: ALWAYS wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. • The label on your tool may include the following symbols. The symbols and their definitions are as follows: V ................. volts A ...............amperes Hz ............... hertz W ..............watts min ............. minutes ...........alternating current no .........
PAGE 6
NOTE: Align ribs on inside of depth locator with grooves in clutch housing before snapping into place. CHANGING BIT TIP 1. Pull forward on adjustment collar and remove it from clutch housing (Fig. 3). The reversing lever is used to reverse the tool for backing out screws. It is located above the trigger, shown in Figure 1. To reverse the screwdriver, turn it off and push the reversing lever to the right (when viewed from the back of the tool).
PAGE 7
2. Place nutsetter into clutch housing and push end of nutsetter until ball lock snaps into groove of nutsetter shank. 3. Reassemble adjustment collar by snapping over springs (Fig. 4). NOTE: Align ribs on inside of depth locator with grooves in clutch housing. DEPTH ADJUSTMENT 1. For washer head screws: rotate adjustment collar until end of nutsetter is flush with end of locator. 2. For large washer head and sealer screws: adjust as above until nutsetter is recessed approximately 1.
PAGE 8
Changing Clutches Recommended accessories for use with your tool are available at extra cost from your local service center. If you need any assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 Australia or call 1800 654 155 or (NZ) 09 259 1111. FIG. 6 1. Remove clutch housing by unscrewing (left hand thread). 2. Clamp tool or clutch housing in a resilient clamp. USE CARE, the clutch housing can be easily damaged. 3.
PAGE 9
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call (AUS) 1800 654 155 or (NZ) 09 259 1111 for a free replacement.
PAGE 10
8
PAGE 11
9
PAGE 12
DEWALT Industrial Tool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (03 8720 5100) • 5 Te Apunga Place, Mt Wellington, New Zealand (09 259 1111) (OCT07) Part No. 1007746-00 DW251-XE, etc. Copyright © 2007 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.