Installation guide

ManualsBrandsDialogic ManualsComputer equipment& Loop Start

Installing the Dialogic®

Brooktrout® TR1034 DID/DID

& Loop Start PCI Fax Board

Part Number: 931-127-05

The Dialogic® Brooktrout® TR1034 Analog Loop

Start (ALS), Analog Direct Inward Dialing (DID), or

combination ALS/DID PCI Fax Board (“TR1034” or

TR1034 fax board(s)”) is a half-sized, single-slot,

PCI-bus compatible fax board. This board provides

the following:

 On-board analog connections

 V.34 (33.6 Kbps) fax transmission speeds

 Up to four fax or voice channels per board

This installation guide provides information about:

 Safety Compliance Statements

 System Requirements (including telephone

services)

 Setting the Module Number

 Installing the Dialogic® Brooktrout® Fax Board

 Recognizing PCI Slots

 Connecting the Phone Service

 Understanding LED Signals

 Using the TR1034 DID/DID & Loop Start Board

 Getting Help

Safety Compliance Statements

 Install this board only in UL Listed equipment

that has instructions stating that the user may

install and remove accessory boards.

 Disconnect any TNV circuit connectors

(telephone line cords) from this board before

removing the cover of the equipment.

 Models of this board that contain DID interfaces

are for use only in equipment that has a

permanent connection to protective earth and is

installed in a restricted access location.

System Requirements

This board must be installed in an enclosure that

meets the following specifications:

 A Pentium or later host processor

 An available 33 or 66 MHz, 32- or 64-bit PCI bus

slot. See

Recognizing PCI Slots for more

information.

The TR1034 ALS/DID PCI Series boards can be

used in either 3.3V or 5V signaling PCI slots.

 Temperature: 0° C - 50° C

 Humidity: 10% - 95% (non-condensing)

 Power Requirements:

One or both of the following telephone services are

also required:

 Analog loop start interface

 Analog direct inward dialing interface

Setting the Module Number

Set each board to a unique module number to easily

identify the resources associated with a specific board

in a multi-board system.

Use the SW-1 rotary switch to set a unique module

number for each board. See Figure 4 for the switch

location. Select a number from 2 - F on the rotary

switch. Settings 0 and 1 are reserved and cannot be

used.

Installing the Dialogic®

Brooktrout® Fax Board

To install your fax board:

1. Turn off your PC and remove the cover.

2. Locate a free PCI bus slot, and remove the slot

cover.

3. Carefully align the board with the slot and firmly

seat the board into the slot.

4. Tighten the mounting bracket screw to secure the

board to the chassis.

5. Replace the cover.

6. Turn on your computer.

Note: Dialogic® Brooktrout® fax boards should not be present

in the computer during the installation of any operating

system. The operating system might misinterpret the

board as being some other device, with unpredictable

consequences.

Recognizing PCI Slots

The PCI slots in the computer chassis usually appear

as white slots. Your Dialogic® Brooktrout® fax board

can be inserted into any of the PCI slots shown in

Figure 1.

Figure 1. PCI Slots

Connecting the Phone Service

The appropriate telephone service and hookups must

be installed at your site in order to connect to

telephone service.

Table 1 shows the relationship between channel and

connector for each board configuration.

Use the cable supplied with the board. See Figure 2

for pinout details for your board.

Use the following instructions to connect your board

to ALS or DID service.

1. Plug one end of the cable into the A or B RJ-45

telephone connector on the board (see Figure 3

and Figure 4 to locate connectors).

2. Plug the other end into the wall connector for

your telephone service.

Board +5V +3.3 V Total Power

Combination

2 ALS and 2 DID

Channels

1.5A 1.0A 10.8 W

4 DID Channels

3.0A 1.0A 18.3 W

Caution: A small amount of static electricity can

destroy the sensitive components on your fax

board. To prevent static damage, always connect

yourself to ground using a ground strap before

touching a circuit board. Handle boards only by the

edges or metal mounting brackets and transport

boards in an anti-static bag.

Warning: When installing the board, be sure that

the mounting bracket is securely fastened to the

chassis and the chassis is plugged into a

grounded three prong plug. Improper chassis or

bracket grounding can result in harmful or fatal

electrical shock as well as component damage.

5V 64-Bit Connector

3.3V 32-Bit Connector

Insert the connector into any of these slots.

3.3V 64-Bit Connector

5V 32-Bit Connector

Universal PCI Board Edge Connector

Table 1: Channel and Connector Relationship

TR1034+uP4C-R

(Two ALS and Two DID Channel Configuration)

Channel

Number

RJ-45

Connector Type of Service

ALS

DID

TR1034+uP4D-R

(Four DID Channel Configuration)

DID

TR1034+uP2C-R

(One ALS and One DID Channel Configuration)

0A ALS

1B DID

TR1034-P2-2L

(Two ALS Channel Configuration)

ALS

TR1034+uP2D-R

(Two DID Channel Configuration)

DID

Summary of content (2 pages)

PAGE 1
Installing the Dialogic® Brooktrout® TR1034 DID/DID & Loop Start PCI Fax Board Part Number: 931-127-05 The Dialogic® Brooktrout® TR1034 Analog Loop Start (ALS), Analog Direct Inward Dialing (DID), or combination ALS/DID PCI Fax Board (“TR1034” or TR1034 fax board(s)”) is a half-sized, single-slot, PCI-bus compatible fax board. This board provides the following: On-board analog connections V.34 (33.
PAGE 2
Port A No connection No connection Tip 1 Ring 0 Tip 0 Ring 1 No connection No connection Port A = ALS or DID Port B No connection No connection Tip 3 Ring 2 Tip 2 Ring 3 No connection No connection Table 2 and Table 3 describe how the end panel LEDs provide information. Table 2: Channel LEDs Channel LEDs Meaning Off Channel is on hook (inactive). Channel is off hook (active). Incoming ring signal (ALS only). Flashing at 0.