User`s guide

Dialogic
®
System Release 6.0 PCI for Windows
®
Release Update, Rev 62 — January 30, 2008 292
Dialogic Corporation
Resolved IPY00008476 32065 18 D/240JCT-T1 With high call load, a firmware crash occurs on
Dialogic
®
D/240JCT-T1 Boards running NTT protocol.
Resolved IPY00012124 28389 -- D/300JCT-E1 Dialogic
®
D/300JCT-E1 Board crashes with an
unstable E1 line.
Resolved IPY00012757 27544 -- D/480JCT-2T1 When trying to configure the Dialogic
®
D/480JCT-2T1
Board for SoftFax capability, the spfax.fwl firmware file
option is listed as available for “FirmwareFile” (span 1)
category but not for “FirmwareFile2” (span 2) in their
respective pull-down menus.
Resolved IPY00011986 28826 -- D/480JCT-2T1 dx_stopch( ) does not terminate call progress
analysis when using DX_CAP parameter: ca_intflg =
DX_PVDOPTNOCON, or DX_PVDENABLE, or
DX_PVDOPTEN.
Resolved IPY00030589 25101 -- D/600JCT-2E1 Windows
®
Device Manager fails to install Dialogic
®
D/600JCT-2E1 Board.
Resolved IPY00030882 36057 108 D/82JCT-U Dialogic
®
D/82JCT-U Board is not reporting rings to
the application consistently.
Resolved IPY00008169 31242 18 D/82JCT-U Dialogic
®
D/82 firmware is not reading proper
integration data from the 2-line display when
integrated with vectors instead of hunt groups on a G3
switch. It only reads the second line of the display.
Resolved IPY00008405 32026 18 D30EP The Dialogic
®
D30EP Board should respond with REL
COM message after receiving a SETUP message
including the IBCAP message block.
Resolved IPY00030597 29237 -- DCM Dialogic
®
DM/V480-2T1 and DM/V960-4T1-PCI
Boards are not detected by DCM on a Windows
®
2003
system (.NET).
Resolved IPY00028248 33718 154 DCM The board and protocol descriptions for
ml10_dsa_net5.pcd are incorrect in the DCM Assign
Firmware File dialog box.
Resolved IPY00019208 23343 -- DCM ML2_120 is displayed in DCM instead of ML6_120
when configuring an E1 QS A with Media Load 6.
Resolved IPY00019147 29041 -- DCM Default setting of DISI32_R2_UK.config is mu-law
even though UK uses A-law.
Resolved IPY00014213 28818 -- DCM When the RTF is activated and the DCM is stopped,
the size of rtflog.txt generated becomes 0 KB.
Resolved IPY00014103 28004 -- DCM The DCM cannot load certain .tsf files properly to
detect certain tones, especially when a tone is noisy
and the volume is low.
Resolved IPY00012759 27658 -- DCM Under the Interface tab in DCM, users are allowed to
put a blank in the place of ISDNProtocol and
ISDNProtocol2 instead of “None” and this leads
customers to wrongly believe that this is the method to
download non-ISDN firmware.
Table 9. Issues Sorted By Type, Dialogic
®
System Release 6.0 PCI for Windows
®
(Continued)
Issue Type Defect No.
PTR
No.
SU
No.
Dialogic
®
Product(s) or
Component(s)
Description