DIAMOND DIGITAL DX-D193P Colour TFT LCD Monitor 19” (43 cm) LCD Panel Size
Copyright 2008, Mitsubishi Electric Australia Pty. Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission.
CONTENTS 1 1.1 1.2 Safety Disclaimer Important Safety Instructions 3 3 3 4 2.2 2.3 Introduction Before Installing Your Monitor Unpacking Precautions 4 4 4 3 3.1 3.2 3.3 3.4 3.5 Exploded View Front Panel Configuration Bottom Panel Configuration Side Panel Configuration Tilt / Swivel Angle Dimension 5 5 6 7 8 8 4 4.1 Production Description Supported Timing Table 9 9 5 5.1 5.2 5.3 5.4 5.5 5.
1 Safety 1.1 Disclaimer This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of this company to notify an person of such revision or changes.
2 Introduction 2.1 Before Installing Your Monitor Thank you for choosing our new generation DX-D193P monitor. This lightweight, slim design LCD monitor includes many outstanding features and combines the benefit of a high resolution display. Please follow ALL instructions and cautions carefully before using this product. Keep this user manual safely stored for future reference. Read this manual cover to cover. Pay attention to all warnings and cautions.
3 Exploded View 3.1 Front Panel Configuration Figure 3.1 Ref # Button Front Panel function description of DX-D193P Function Description Press to switch monitor on / off. 1 POWER 2 LED Indicator 3 MODE 4 AUTO Green: Power on ; Orange: No signal ; Red: Power saving ; NA: Power off see ※ Note Input source VGA signal auto adjustment. 5 Press to increase the value of OSD option selected and increase volume.
3.2 Bottom Panel Configuration Figure 3.2 Bottom Panel function description of DX-D193P Input /Output Interface Ref # Connector 1 PC Audio In 2 Component (YPbPr) Description For audio source of R.G.B input terminal. Connect to component input, such as the video output of a DVD player. 3 Audio In Audio source for Component input 4 VGA Connect to R.G.B input, such as the VGA output terminal of a personal computer.
3.3 Side Panel Configuration Figure 3.
3.4 Tilt / Swivel Angle The viewing angle of the monitor can be adjusted to the most comfortable monitoring status. Min Degree Max Degree 5 degree 40 degree 3.
4 Product Description The DX-D193P TFT-LCD Security Monitor with Protective Glass displays PAL colour pictures in CCTV systems. There are 2 sets of Composite Video BNC connector inputs/outputs, 2 sets of RCA audio input/outputs, 1 set of L/R RCA Audio inputs for Component (YPbPr) and 1 S-Video (Y/C) input and output using a 4-pin mini-DIN. Each model includes an Analog VGA input using 15-pin D-sub to accommodate the increasing use of PCs and digital video devices in security applications.
5 Monitor Installation This chapter outlines the procedures to install the DX-D193P TFT-LCD Security Monitor with Protective Glass. A qualified service person should install the monitor and adhere to all local codes. 5.1 Ventilation To prevent overheating, ensure that the ventilation openings on the rear of the monitor are not covered. 5.2 Desktop Installation The DX-D193P TFT-LCD Security Monitor comes with a 12V/4A power adapter.
5.4 Connecting the Y/C (S-Video) Signal to the Monitor There is 1 set of mini-DIN type connectors for the S-Video (Y/C) input/output on the rear side panel (see Figure 3.3). 5.5 Connecting the YPbPr Signal to the Monitor There is 1 set of YPbPr connectors for the S-Video (Y/C) input/output on the rear side panel Connect the signal cable to the connectors with same colors (green/blue/red) 5.
6 Navigating the Monitor 6.1 Navigating the Monitor On-screen Display(OSD) The DX-D193P TFT-LCD Security Monitor has several modes: Composite1/2, YPbPr, VGA, DVI and S-Video. The LCD monitor is programmed through the on-screen display (OSD) menus and submenus where an operator can select operating parameters. To access the OSD menus, press the Menu button on the front panel. Use the front panel of the monitor to make any necessary adjustments to the OSD.
6.2.1 VGA/DVI Signal OSD Menu Main Menu Sub Menu _ PIP/POP * Above Value/data is for reference only. Change without notice.
6.2.2 VGA/DVI Signal OSD Function Table Main Menu REF.
6.2.3 Video(Composite/YPbPr/S-Video) Signal OSD Menu Main Menu Sub Menu *Above value/data is for reference only. Change without notice.
6.2.4 Video(Composite/YPbPr/S-Video) Signal OSD Function Table Main Menu REF.# Submenu Definition 1 Brightness Adjusts the brightness level (range 0-100) 2 Contrast Adjusts the contrast level (range 0-100) 3 Tint Adjust the colour tint. (NTSC only) (range 0-100) 4 Color Adjust the colour density (range 0-100) 5 Color Temp. Press (+) or (-) to choose three types of colour temperature 9300°K , 6500°K or User Colour. 6 Sharpness.
6.2.5 Input Signal Icon VGA Signal Composite Signal S- Video Signal DVI Signal YPbPr Signal 6.2.
7 Troubleshooting Guide Problem Solution No image is displayed on – screen “No Signal” message is displayed Display image is not centered, is too small, or – – – – – Check that the power cord of the monitor is securely connected to the wall outlet or grounded extension cable or strip. Power switch should be in the ON position and the LED illuminated. The signal cable should be completely connected to the video card/computer.
8 Technical Specification Model DX-D193P Monitor Size 19 inch with protective screen Pixel pitch (H x V mm) Max. VGA / DVI Resolution Dimension (W x H x D mm) 0.294 x 0.294 1280 x 1024 pixels /85 Hz 421.2 x 408.8 x 240 VGA、DVI、Composite、S-VIDEO、Component. Display Mode Signal Connector DC In/Out, VGA In, DVI In, BNC1 In/Out, BNC2 In/Out, Y/C In/Out, YPbPr In, Audio1 In, Audio2 In, Audio3 In, PC Audio In Power Input DC Input : 12V / 4A.
WARRANTY WARRANTY After Sales Service After this product is unpacked, keep the carton and packing materials to ensure safe transportation in case of any after sales service. The warranty is covered by a 3-year limited warranty, subject to normal conditions of use. If you experience any problems with this product please contact your local dealer or supplier for repair and maintenance instructions.
Service Contacts Australian Service Contacts Visit the Customer Support page of Mitsubishi Electric Australia’s web site at; www.mitsubishielectric.com.