Installation Guide

ManualsBrandsDiamond NOW ManualsKitchenDenver 36-in W x 35-in H x 23.75-in D Natural Blind Corner Base Stock Cabinet

800026-Rev 0

Parts Included:

• Square Corner Cabinet

• Filler - (Shipped on underside of cabinet)

• Blind Panel - (Shipped on underside of cabinet)

Materials Needed

• #6 x ½” Flat Head Screws

• 2 ½” Trim Head or Flat Head Wood Screws

• 2 ½” Round Washer Head Screws

(6.18.13) SCB INSTRUCTIONS A5131

Instructions for Square Corner Cabinet Installation

Parts Included:

(1) Blind Panel

(1) Square Corner Cabinet

(1) Filler Board

Tools Needed:

Phillips Head Screwdriver, Tape Measure,

Marking Tool, Drill with 7/64” Bit and 3/32”

Bit, Saw

Square Corner Cabinet Information:

STEP 1

Parts Needed:

(8) #6 x 1/2” Flat Head Screws

(2) #10 X 2 1/2” Washer Head Screws

(2) # 8 Flat Head Screws of Appropriate length

KEY

X: Minimum pull for

Square Corner Cabinet

Y: Maximum pull for

Square Corner Cabinet

Z: Minimum filler size

required between

cabinets

Min. pull is defined

when square corner or

adjacent cabinet doors

can be opened 90 deg.

and/or drawers can be

fully extended without

hitting adjacent cabinet

door/drawer when shut.

SQUARE CORNER

CABINET

ADJACENT

CABINET

Filler Board

Wall

=Open Space

Min. Pull

Min. Pull w/Hardware

Max. Pull

Min. Filler Required Min. Filler Required w/Hardware

1 1/4" Overlay

3/4" 2 1/4" 12 1/2" 1" 2 1/2"

7/16" Overlay

1/4" 1 3/4" 12 1/2" 1/2" 2"

NOTE: To determine your cabinet’s over-

lay, measure the distance from the

drawer or door to the edge of the face

frame and reference the drawing above.

Remove baseboard and other objects on the wall

area where the cabinets are to be installed. Using a

straight edge and a level, find the high point in the

floor where the cabinets are to be installed. From the

high point, mark a level horizontal line on each wall

where the cabinets will be attached. From the level

lines mark another parallel level horizontal line 35" up

for base cabinets, 54" for wall cabinets and 84", 90"

or 96", depending upon your tall cabinet heights. The

top of the base and tall cabinets and the bottom of

the wall cabinets will be located at these marks.

ATTN: FILLER BOARD AND COVER PANEL ARE STAPLED

UNDERNEATH YOUR SQUARE CORNER BASE CABINET.

NOTE: To determine your

cabinet’s overlay, reference

left image showing door &

drawer front coverage of

face frame

(6.18.13) SCB INSTRUCTIONS A5131

STEP 2

STEP 3

STEP 4

The blind panel will need to be trimmed to size to fit

over the opening of your square corner base cabinet.

Then the blind panel will need to be drilled for

installation. Mark the (8) hole locations shown to the

right on the blind panel. All holes should be located

1/4" from edges of blind panel. Drill the (8)

premarked locations with a 7/64" diameter drill bit

through the panel.

*Panel is located under cabinet with Filler Board

Locate the studs with a stud finder and mark where

the cabinets are to be installed. Remove all the doors

and drawers from the cabinets before installation.

Measure the area to confirm that the kitchen design

used will work.

Remove door and drawer from square corner

cabinet. On the square corner opening side

of the face frame (opening without door

attached), a line 1/2” from the edge of the

opening needs to be marked onto the face

frame. This will locate the blind panel for

attachment.

NOTE: Door can be placed on either side of

the cabinet depending on design needs.

DOOR LOCATION

FACE FRAME

1/2

Step 1: Inspect and Preparation

Follow Wall and Base Cabinet instructions for cabinet inspection and preparing

and marking the walls for cabinet installation. Install all wall cabinets before

installing the SCB corner cabinet.

Square Corner Cabinet Information:

Full Overlay Partial Overlay

Step 2: Blind Panel Preparation

Locate and remove the blind panel and ller from the underside of the cabinet.

Set ller aside for later use. Trim blind panel so it covers the open side of the blind

corner cabinet by 1/2" on all (4) sides of the opening. Mark (8) hole locations

shown in the image to the right ¼” from the edges of the blind panel. Predrill the

(8) marked locations with a 3/32” diameter drill bit.

Step 3: Blind Panel Installation

On the square corner opening side of the face frame (opening without the door

attached), mark lines onto the face frame ½” from the edge of the door opening.

This will locate the blind panel for attachment. Place predrilled blind panel onto

face frame and mark the pre-drilled hole locations from the blind panel onto the

face frame. Remove blind panel and predrill face frame with a 3/32” diameter

drill bit in all (8) locations, ½” deep. Attach blind panel to face frame using (8)

#6 x ½” at head screws.

Square Corner Cabinet

Installation Instructions

CAUTION: Never use nails to mount cabinets. The use of nails may

void your factory warranty, written or implied.

(6.18.13) SCB INSTRUCTIONS A5131

STEP 2

STEP 3

STEP 4

The blind panel will need to be trimmed to size to fit

over the opening of your square corner base cabinet.

Then the blind panel will need to be drilled for

installation. Mark the (8) hole locations shown to the

right on the blind panel. All holes should be located

1/4" from edges of blind panel. Drill the (8)

premarked locations with a 7/64" diameter drill bit

through the panel.

*Panel is located under cabinet with Filler Board

Locate the studs with a stud finder and mark where

the cabinets are to be installed. Remove all the doors

and drawers from the cabinets before installation.

Measure the area to confirm that the kitchen design

used will work.

Remove door and drawer from square corner

cabinet. On the square corner opening side

of the face frame (opening without door

attached), a line 1/2” from the edge of the

opening needs to be marked onto the face

frame. This will locate the blind panel for

attachment.

NOTE: Door can be placed on either side of

the cabinet depending on design needs.

DOOR LOCATION

FACE FRAME

1/2

(6.18.13) SCB INSTRUCTIONS A5131

STEP 5

STEP 6

STEP 7

Attach the blind panel to the face frame

using the recommended (8) #6 x 1/2" flat

head screws. These screws must be

purchased separately. Reattach the door

and drawer front to the cabinet.

Place the predrilled blind panel onto the

face frame using the markings placed on

the face frame in the last step. Mark the

predrilled hole locations from the blind

panel onto the face frame. Remove the

blind panel and predrill the face frame (8)

places with a 7/64" diameter drill bit, 1/2"

deep.

Position the Square Corner Base cabinet

with reference to the specifications on

page one. Do not secure to the wall yet.

SQUARE CORNER

CABINET

ADJACENT

CABINET

Filler Board

Wall

=Open Space

MARK

(8) HOLE

LOCATIONS

ONTO THE

FACE FRAME.

Attach panel to the face frame

using the (8) #6 x 1/2"

flat head screws.

NOTE: Door can be placed on either side of the cabinet depending on design needs.

Summary of content (3 pages)

PAGE 1
Square Corner Cabinet Instructions for Square Corner Cabinet Installation Installation Instructions ATTN: FILLER BOARD AND COVER PANEL ARE STAPLED CAUTION: Never use nails to mount cabinets. The use of nails may void your factory warranty, written or implied. UNDERNEATH YOUR SQUARE CORNER BASE CABINET.
PAGE 2
STEP 7 STEP 4: Begin Square Corner Cabinet Installation Position the Square Corner Base cabinet with reference to the specifications on page one. Do not secure to the wall yet. Wall STEP 8 Position the square corner cabinet and the adjacent cabinet in place with STEP 8 reference to the filler and pull specification table on page 1. Setting the Once the square corner base cabinet is positioned in step 5, confirm that the cabinet is sitting level and straight.
PAGE 3
STEP 11 Clamp Wall SQUARE CORNER CABINET With the adjacent cabinet positioned next to the installed square corner cabinet, mark the location of the filler board on the inside of the square corner cabinet face frame. STEP 13 STEP 8: Adjacent Cabinet Installation Once the square corner cabinet has been installed, the adjacent base cabinets can now be installed. Start installing the base cabinets in the corner. Using clamps, align and join the cabinets together at the face frames.