PRACTICAL USER’S GUIDE FOR THE ELECTRIC FIREPLACE MODEL NUMBERS: BF33ST/DX BF39ST/DX BF45ST/DX Write Your Remote Control Code Number Here: Quality checked by: Valued Customer, We are pleased that you have chosen to purchase an electric fireplace manufactured by Dimplex North America Ltd. Over the years, valuable memories will occur around the warmth and comfort of your hearth. Thank you for allowing our product to be the backdrop for those special moments.
QUICK REFERENCE GUIDE FOR THE ELECTRIC FIREPLACE 1. Prior to the first use of the fireplace verify the following: • Are the circuit breakers for the fireplace on? • Are the light bulbs in your fireplace loose? (to check, follow the instructions for replacing the light bulbs under the maintenance section of this manual) 2. The heater on your fireplace may emit a slight, harmless odor when first used.
CONTENTS PAGE 1 Important Instructions PAGE 2 Model and Serial Number Information PAGE 4 Operation PAGE 5 Maintenance PAGE 6 Accessories PAGE 7 Warranty
IMPORTANT INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this fireplace. 2. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation.
IMPORTANT INSTRUCTIONS If you have any questions about out products please have the product model and serial numbers available upon calling Dimplex customer service. To locate the model and serial number labels see below.
Model Number Serial Number Carton 3
OPERATION The controls for the Electric Fireplace are located at the bottom right hand corner of the unit. MANUAL CONTROLS FIGURE 1 MANUAL CONTROLS A. Main Power Switch Main on/off switch, activates the flame effect B. Heater Control Switch Heater ON/OFF switch, activates the heater MAIN POWER SWITCH HEATER CONTROL SWITCH WALL MOUNTED CONTROLS FIGURE 2 The fireplace can be installed with wall mounted controls. These controls include wall switches and thermostats.
the room temperature at this setting. For additional heat, turn the thermostat clockwise until you hear the click again and the heater will turn on. To turn the heater off, turn the thermostat counter clockwise all the way, and/or turn the manual heater switch on the unit to the OFF position. RESETTING THE TEMPERTURE CUTOUT SWITCH The heater on this fireplace is protected with a safety device to prevent overheating.
To access the light bulb area (BF33ST/DX, BF39ST/DX,BF45ST): 1. Open steel curtain (remove glass doors if applicable). 2. Remove two screws on log bracket and set aside. (FIGURE 3) 3. Pull front edge of plastic ember bed or plastic grate up and forward until rear tab releases from the ledge located at the bottom of the mirror. (FIGURE 4) Note: Log set fits tightly into firebox, some force may be necessary to remove. 4. Examine the bulbs to determine which bulbs require replacement. 5.
To access the light bulb area (BF45DX) 1. Open steel curtain (remove glass doors if applicable). 2. Remove two screws on log bracket and set aside. (FIGURE 3) 3. Pull front edge of plastic ember bed or plastic grate up and forward until rear tab releases from the ledge located at the bottom of the mirror. (FIGURE 4) Note: Log set fits tightly into firebox, some force may be necessary to remove. 4. Set logset in front of firebox. 5. Disconnect the logset LED wire harness from unit. (FIGURE 5) 6.
Mirror Cleaning The mirror is cleaned in the factory during the Assembly operation. During shipment, installation, Handling, etc., the mirror surface may collect dust Particles; these can be removed by buffing lightly With a clean dry cloth. To remove fingerprints or other marks, the mirror can be cleaned with a damp cloth using good quality household glass cleaner. The mirror should be completely dried with a lint free cloth to prevent water spots.
TWO YEAR LIMITED WARRANTY Products to which this limited warranty applies This limited warranty applies to the following models of your newly purchased Dimplex electric fireplace BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX, and to newly purchased Dimplex fireplace surrounds (mantels) and trims.
What you must do to get service under this limited warranty Defects must be brought to the attention of Dimplex Technical Service by contacting Dimplex at 1-888-DIMPLEX (1-888-346-7539), or 1367 Industrial Road, Cambridge Ontario, Canada N1R 7G8. Please have proof of purchase, catalogue/model and serial numbers available when calling. Limited warranty service requires a proof of purchase of the product.
What Dimplex and its dealers and service agents are also not responsible for: IN NO EVENT WILL DIMPLEX, OR ITS DIRECTORS, OFFICERS, OR AGENTS, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY, WHETHER IN CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT, EVEN IF DIMPLEX OR ITS DIRECTORS, OFFICERS, OR AGENTS HAVE BEEN ADVISED