LAN + WiFi + Cellular Smart Home Alarm System User Manual
Table of Content ● Introduction P2 ● Notice P2 ● Safety P3 ● Requirements P3 ● System Status & User Authorities P4 ● Appearance P5 ● Setup P7 ● App operation introduction P9 ● FAQ P15 ● Specifications P16 1
Introduction • Thank you for purchasing the Nova Pro Smart Alarm System. Nova Pro offers you a complete control over your home security and automation via your smartphone. This manual will guide you through the setup procedures and highlight some key features. • The system operates on smartphones. • Please note that all contents listed here might be slightly different from the contents of the package or the App. Please check the latest version of the user manual. • Version: V1.
Safety • This system is designed to minimize majority of risks and to ensure the safety of your home, however it does not guarantee protection against burglary, robbery, theft, or any type of emergencies. Users should continue to act prudently to protect the security of their lives and property. • Any alarm system is subject to compromise or failure for a variety of reasons as follows: - An intruder may gain access through unprotected openings.
System Status & User Authorities • The Nova Pro system does not support any wired sensors. The panel communicates with all sensors via wireless RF signals. Most of the sensors have low battery warning features. In the event of low battery, notifications will be sent to the APP. Smoke detector and CO sensor work at full time. • The system can set its security status according to the commands given by users or the signals sent from the triggered sensors.
Appearance • Rear View • Top View Power Buzzer Ethernet SIM Slot Indicator STATUS LED INDICATION Operation Light ON ARM/DISARM/HOME ARM/SOS.
• Bottom View Wall Mounting Bracket Siren Battery Cover Network Configuration Button Reset Button Power Switch 6
Setup • Internet Connection Requirements - Please ensure the router you are using has already been connected to the Internet with DHCP mode enabled. Nova Pro supports IPV4 protocol only. - The system supports the following types of connection: - LAN: 10/100M Ethernet. - Wi-Fi: 2.4GHz, WEP/WPA/WPA2 encrypted. • Place the Panel at a Suitable Place - If Wi-Fi is used to connect the panel to internet, please make sure the panel is placed under Wi-Fi coverage before installation.
• Add the Panel - Make sure your mobile phone is connected to the Internet. Open the APP, click on “Add a new device” • Set Up Password - APP will automatically scan for panels available nearby and display their names for which you can choose to connect. After successfully connecting the panel, please rename the device and setup a password for future configuration purpose.
• Configure the Wi-Fi Setting of the Panel - Select the Wi-Fi you want the panel to connect with and input the password to finish setup. • Check Setting - Make sure your mobile phone has been connected to the Internet via cellular or Wi-Fi. - Try pressing ARM/DISARM button in the App, to see if the status icon would be changed accordingly. - Try using remote control, pressing ARM / DISARM button to see if the status icon in the App would be changed accordingly. • Installation - Close the battery cover.
APP Operation Introduction • Home Page User Settings Device List The entry for all account settings. - Device List. - Account Information: Phone, Email and Password. Select the panel to be managed from dropdown list. - Add/Remove panels. Real-time Status Diagram System & App Settings It shows a real-time system status and the quality of network connection. Any change of system status is indicated in the diagram. Colors and icons are used here for better illustration.
• Dashboard - Press Dashboard to switch to the dashboard page. - You can press SOS to trigger alarm or enter device control page. • Pairing New Accessories Scan QR Code Tap [Scan QR Code] Recommended Code is printed on every accessory.
• Delete an Accessory - Choose the accessory to be removed from the system, and slide the column to the left until a “Delete” button appears. - Click the “Delete” button and confirm to finalize the removal. • Share with Others - The owners can easily share their devices with the family members or friends. - Select [System Settings] - [Share this device with others] should generate a unique QR code which contains the identification of shared panel and the assigned authority.
• Emergency Contacts Settings - All App users are listed in Emergency Contact list automatically. - Users can add mobile phone numbers in [Other Contacts] list. - For the App users, the [Push Notification] option is enabled by default, while the [SMS Notification] is disabled by default. (SIM card required) - For other contacts, the [SMS Notification] is enabled by default. - When an emergency occurs, the App users should get push notifications, while other users get alert SMS message sent from the panel.
• Home Arm Settings - By configuring Home Arm status in the APP, users can activate certain sensors while at home. - When [Home Arm] button is activated for the first time, the setup procedure should commence. - Only those sensors support Home Arm feature will be listed here. • Accessories Management - All accessories are listed in [Device Setting]-[Accessories Management], and are sorted by their types. - Users can add, remove, and modify their settings here.
• Advanced Settings In this section, the following settings can be executed: - Security Notifications Settings: it allows to setup notification language and duress alarm, which allows users to input pre-set duress code on the keypad to stop alarm and meanwhile send pre-set emergency messages to other designated contacts. - Ready to Arm: if this feature is enabled, when arm or home arm the premises, the system will notify if there is a contact sensor is in open status.
FAQ Q: When the Internet connection is down, can the system still protect me? A: LAN/Wi-Fi/Cellular are used for communication. As recommended, LAN provides the most reliable Internet connection. In case that LAN and Wi-Fi both fail, the cellular network will work as a backup. In most cases, the disconnection of Internet is caused by electricity failure, which means the system might have to run with the backup battery.
Specifications Capability CPU Working Environment ARM Cortex-A7 Power Supply Working Temp. -10°C~60°C Installation & Materials Auxiliary power DC 5V 2A Installation Desktop, Wall Mounted Backup batteries Rechargeable Lithium Polymer battery 2200mAh Shell Material ABS/PC Stand-by time 8 hours (fully charged) Key Features RF Capability Total input accessories 99 Frequency 433.92MHz Keypad Supported Works with wireless keypad Distance 300 m. / 1000 ft.
