user manual

ManualsBrandsDMP Electronics ManualsNetwork RouterInc. Network Router LT-0424

PROGRAMMING INSTRUCTIONS Ether-Com

LT-0424 (1/99)

2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282

Description

The Ether-Com

Single Port Router allows a DMP 1912XR, XR200 or XR200-485 Command Processor

panel to

communicate to a DMP SCS-1 Receiver using an existing Ethernet network. The router operates as an interface

between the panel and the network.

Whats needed

Additional equipment needed to program the Ether-Com

386 or better laptop or PC

Windows

95 or 3.1 with a communication software package such as Hyperterminal

or Terminal

DMP Model 396 programming cable

10BaseT Ethernet cable

Configuration for use with a DMP 462N or 862N

The following configuration is designed for applications where the Ether-Com

server is used as the interface

between the DMP 462N or 862N Network Interface Card on a 1912XR/XR200/XR200-485 panel and an ethernet

network.

1912XR/862N orXR200/462N

Configure the communication software package on your laptop or PC for 9600 baud, 8 bits, no parity 1 stop bit and

no flow control. Connect the DMP Model 396 programming cable to the COM port on your laptop or PC that you

configured in your communication software. Connect the other end of the Model 396 programming cable to the

Ether-Com

connector supplied with the unit.

DO NOT CONNECT the Ether-Com

to an Ethernet network at this point. Apply power to the unit. If the unit

passes its power-up diagnostics the following message should be displayed:

Ethernet Address: 00-80-a3-0f-4a-d4 Internet Address: 10.17.39.1

Flash Rom Version 2.0 (May 12, 1998)

Flash Version: 3.5/1 (970707)

Current Diagnostics report:

NVR Config: Normal Ram Size: 256 KB

CPU Speed: 10 MHz Gate Array: Rev 2

Flash Version: 3.5/1 (970707) Ethernet: None

Errors: Network

No network was detected. Press a key within

10 seconds to access bootmode commands>

Press the Return key to access the Boot> prompt.

Enter the following commands at the Boot> prompt:

CHANGE BOOTP DISABLED

CHANGE DHCP DISABLED

Downloaded from: http://www.guardianalarms.net

Summary of content (4 pages)

PAGE 1
PROGRAMMING INSTRUCTIONS Ether-ComTM Description The Ether-ComTM Single Port Router allows a DMP 1912XR, XR200 or XR200-485 Command ProcessorTM panel to communicate to a DMP SCS-1 Receiver using an existing Ethernet network. The router operates as an interface between the panel and the network. Whats needed Additional equipment needed to program the Ether-ComTM: 386 or better laptop or PC WindowsTM 95 or 3.
PAGE 2
3. CHANGE RARP DISABLED Connect the ETHER-COM to an Ethernet network after entering the command in line number 3. It should be connected to the actual network at the location where the ETHER-COM will be permanently installed. 4. INIT 451 The ETHER-COM initialization will begin 5 seconds after pressing the Return key. If the ETHER-COM has been properly attached to a network and no other self-diagnostic errors are encountered, the ETHER-COM will restart.
PAGE 3
5. CHANGE FLOW CONTROL NONE 6. CHANGE DEDICATED TCP xxx.xxx.xxx.xxx:2001U (where xxx... is the IP address of the Ether-ComTM connected to the SCS-1 Receiver or PC running Remote Access+TM). 7. CHANGE AUTOSTART ENABLED 8. SHOW SERVER - Check and confirm the unit’s IP address, Subnet Mask and the Gateway address. 10. SHOW PORT - Check and confirm the speed, flow control, dedicated service, and autostart options are set correctly.
PAGE 4
Digital Monitoring Products 2841 E.