Instruction manual

16
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Dolmar tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Dolmar Service Center.
• Cutter blade
• Nylon cutting head
• Pole hedge trimmer attachment (for model AT-3630,
AT-3631)
• Pole saw attachment (for model AT-3630, AT-3631)
• Cultivator attachment (for model AT-3630, AT-3631)
• Dolmar genuine battery and charger
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Noise
ENG905-1
The typical A-weighted noise level determined according
to ISO22868:
Model AT-3623, AT-3624
Sound pressure level (L
pA
): 79.7 dB (A)
Uncertainty (K): 2.5 dB (A)
The noise level under working may exceed 80 dB (A).
Noise
ENG905-1
The typical A-weighted noise level determined according
to EN786:
Model AT-3630, AT-3631
Sound pressure level (L
pA
): 79.3 dB (A)
Uncertainty (K): 2.5 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Vibration
ENG904-1
The vibration emission value determined according to
ISO22867, EN786:
Model AT-3623, AT-3624
Vibration emission (a
h
): 2.5 m/s
2
or less
Uncertainty (K): 1.5 m/s
2
Vibration ENG904-1
The vibration emission value determined according to
EN786:
Model AT-3630, AT-3631
Vibration emission (a
h
): 2.5 m/s
2
or less
Uncertainty (K): 1.5 m/s
2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For European countries only
ENH036-2
EC Declaration of Conformity
The undersigned, Tamiro Kishima and Rainer
Bergfeld, as authorized by Dolmar GmbH, declare that
the DOLMAR machine(s):
Designation of Machine:
Cordless Brushcutter
Model No./ Type: AT-3623, AT-3624
Specifications: see “SPECIFICATIONS” table.
are of series production and
Conforms to the following European Directives:
2000/14/EC, 2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN/ISO11806, EN60335, EN60745
The technical documentation is on file at:
Dolmar GmbH,
Jenfelder Straße 38, Abteilung FZ,
D-22045 Hamburg
The conformity assessment procedure required by
Directive 2000/14/EC was in Accordance with annex V.
Abnormal vibration:
stop the machine immediately!
One of nylon cord has been broken
and the head got unbalanced.
Bump the nylon cutting head against
the ground while it is rotating to cause
the cord to feed.
The cutter blade is bended, cracked or
worn.
Replace the cutter blade.
Cutter blade fastening nut is loose.
Tighten the nut properly as described
in this manual.
Cutter blade is fastened improperly.
The drive system does not work
correctly.
Ask your local authorized service
center for repair.
Cutting tool and motor cannot stop:
Remove the battery immediately!
Electric or electronic malfunction.
Remove the battery and ask your local
authorized service center for repair.
Malfunction status Cause Action