Installation Instructions

ManualsBrandsDonaldson ManualsElectronicsWireless Air Pressure Sensor

for Wireless Sensor Kit X220106

Wireless Air Sensor Install

1. Locate the air ﬁlter housing.

2. If present, remove the visual indicator from the ﬁlter.

3. A tee ﬁtting may be used to install the wireless sensor while retaining the use

of an existing indicator. The use of a Tee ﬁtting is recommended when a wired

sensor or switch is present. Removing a wired sensor from the system may

cause a fault condition.

Application

The Wireless Air Sensor is part of the

Donaldson Intelligent Filtration System. The

system is intended to be installed on both

on-road and off-road equipment requiring

predictive air ﬁlter maintenance. The Wireless

Air Sensor and Easy Receiver are meant to be

installed in conjunction with a GEOTAB GO

device 7, 8, or 9.

Tools

• 7/16," 1/2," or 5/8" wrench (depends on

existing ﬁtting size) — for air ﬁttings

• Diagonal cutters — for trimming zip ties.

Materials

Teﬂon Tape

X220106 Kit Contents

Qty. Part number Description

1 P290025 Instruction manual

1 X220104

Wireless Air

Pressure Sensor 

P290020

Easy Receiver 

P290024

Cable 

P290021

Zip Tie 









Existing visual

indicator

CAUTION

Turn off equipment before

inspecting, removing or

installing an indicator

or sensor.

The Safety Alert Symbol indicates a hazardous situation which, if not avoided could result in death or serious injury.

Obey all safety messages following this symbol to avoid possible injury or death. The possible hazards are explained in

the associated text messages.

This manual contains speciﬁc precautions related to worker safety. The hazard alert image denotes safety related

instructions and warnings in this manual. DO NOT install, operate, or perform maintenance on this wireless sensor kit until you have

read and understood the instructions, precautions and warnings contained within this manual.

Summary of content (4 pages)

PAGE 1
Installation Instructions for Wireless Sensor Kit X220106 CAUTION  Turn off equipment before inspecting, removing or installing an indicator or sensor.  X220106 Kit Contents Qty. Part number Description 1 P290025 Instruction manual 1 X220104 Wireless Air Pressure Sensor  1 P290020 Easy Receiver  1 P290024 Cable  3 P290021 Zip Tie  Application The Wireless Air Sensor is part of the Donaldson Intelligent Filtration System.
PAGE 2
4. Place Teflon tape on the fitting prior to installing the sensor. Teflon tape 5. Install the wireless sensor in place of the existing indicator or tee fitting. X22010 Wireless Sensor Thread the wireless air sensor on the fitting and torque hand-tight. Do not overtighten. Note: Depending on the application, extra fittings may be required to complete the installation. Easy Receiver Install 7. Locate the GEOTAB device. GEOTAB device 8. Remove the dust cover on the GEOTAB device.
PAGE 3
9. Connect the cable to the GEOTAB device using this side of the cable. 10. Place zip tie around GEOTAB device to hold cable in place. Note how the zip tie fits in the groove. 11. Find a secure location to mount the receiver. Make sure that the cable can reach the GEOTAB GO device. • Do not install the receiver in a metal box. Keep it in the open as much as possible. Receiver 13. Insert the other end of the cable into receiver.
PAGE 4
14. Zip ties are provided for securing the Easy Receiver. A reclosable fastener (like Velcro® brand or 3M™ Dual Lock,™ pictured left) is another option, but is not included in the kit. • If using a reclosable fastener, select a flat surface on which to mount it. Clear the surface of dust, oil, and moisture before applying adhesive tape. • Ensure that the receiver is held securely in place. 15.