Quick Start Guide

Quick Start Guide
*Please read the Quick Start Guide carefully before use and keep them properly
目录
Camera App supports Android 4.0+ or iOS 8.0+
system
Method 1: Scan the QR code to quickly download and
install “AISEE”
Method 2: Search for and downloads "AISE E" in the
App Store or Apple Store.
Register Account and Login App
When using AISEE for the first time, please register
and login in the following steps.
After the camera is powered on, open the app and
add camera via Smart Configuration in the following
steps:
After the camera is powered on, open the app and
add camera via AP Mode in the following steps:
Power on camera, please configure the camera after
camera finishes self-test.
There are 3 ways to connect camera to App: connect
via QR Code, connect via Smart configuration and
connect via AP Mode.
If you have any questions or suggestions during
the use of the product, please send us emails to
contact us and provide the following information
* Mobile phone system and model
* AISEE application version number
* Details of questions or suggestions
* Screenshots, photos or videos of questions or
suggestions
* Camera firmware version
* Device ID number
We will email you the corresponding solution based
on the description and information provided.
Click “Register”
After the camera is powered on, open the app and
scan the QR code on app with the camera lens to
add camera in the following steps:
Click “+” or “Add Device”
Choose Smart Camera in “Security&Sensor”
 Please read the instructions in the Quick Start
Guide carefully before using the camera to avoid
danger or loss during use.
 This manual is for use as a guide only. Graphics,
pictures provided in the manual are for explanation
and illustration purposes only, please refer to the
actual product for specific standards. When
installing the product, please make sure the
product is firmly fixed.
 If the product lacks accessories or does not work
properly, please contact the corresponding
distributor for replacement in time and do not
disassemble the product in any way.
(The company assumes no responsibility for any
problems caused by the modification or repair.)
 The descriptions in this manual are for the current
products only, there may be deviations in the
process of updating product. And the company
does not provide any forms of warranty; the special
and indirect damages caused by the use of this
manual or our products will not be compensated.
 In the installation and use of the product, please
strictly abide by the electrical requirements of your
country and the area.
Instruction.............................................................................. 2
Disclaimer............................................................................... 2
Attention................................................................................. 2
Quick Start Guide................................................................. 3
Device Supported............................................................ 3
Ways to Download App................................................. 3
Register Account and Login App................................ 3
Ways to Connect Camera to App .............................. 5
Method 1: Connect via QR Code.......................... 5
Method 2: Connect via Smart Configuration... 7
Method 3: Connect via AP Mode......................... 9
Technical Support............................................................. 12
1
2
3
1 1 1
4 4
5
6
1 1 1 7
1 1 1
8
1 1 1
9
1 1 1
10
1 1 1
11
1 1 1
12
Android
iOS
The camera only supports 2.4G Wi-Fi with 802/b/g/n
protocol, and does not support 5G Wi-Fi. Before
configuring the camera Wi-Fi, please set the router
parameters.
Choose your area and enter phone number or email
Enter the verification code received via phone or email
Enter password for new account
注册账号成功
Click “next step” after hearing camera's prompt tone
Enter Wi-Fi password
Adjust the Q R code position in front of
camera lens within 15~30cm
Camera connects to App
Click “Otherwise”
Choose “SmartConfig”
Camera connects to App
Click “Otherwise”
Choose “AP Mode”
Click camera reset button for 10s then
click “Go connect” on App
Choose “Smartlife_xxxx” hotspot
Click “ AI SEE ” to get back
Camera connects to App
Attention
Disclaimer
Instruction
Quick Start Guide
Device Supported
Ways to Download App
Method 1: Connect via QR Code
Ways to Connect Camera to App
Method 2: Connect via Smart Configuration
Method 3: Connect via AP Mode
Technical Support
Click “+” or “Add Device”
Choose Smart Camera in “Security&Sensor”
Click “next step” after hearing camera's prompt tone
Enter Wi-Fi password
Click “+” or “Add Device”
Choose Smart Camera in “Security&Sensor”
Click “next step” after hearing camera's prompt tone
Enter Wi-Fi password