Installation & Assembly

ManualsBrandsDream On Me ManualsBaby & KidsCaso 2-in-1 Mini Convertible Crib and Changer

STYLE NO: 630

DREAM ON ME INC.

125 HELEN STREET

S.PLAINFIELD NJ 07080

908-791-0555

Read all instructions before assembling crib.

Save instructions for future use.

Adult assembly required.

Small parts may present choking hazard prior to assembly.

Enclosed please find simple step-by-step instructions to help

you quickly assemble your products.Before you begin we

recommend that you following the steps below:

1.Please read the instructions thoroughly.

2. Identify all pa

rts and hardwares

3.You will need the following tools:

Philips head screw driver

Flat head screw driver Hammer

Do Not Use Power Drills or Drivers

To protect your parts during assembly please place them on a

soft surface.

To clean surface use only water on a damp cloth. Do not use

window cleaners or cleaning abrasives as it will scratch the

surface and could damage the protective coating.

Please note that the warning sticker is placed on the cribs to keep parents and

caregivers informed it is a requirement by law under CPSC And ASTM.

We do apologize for any inconvenience this may cause you.

Summary of content (14 pages)

PAGE 1
STYLE NO: 630 DREAM ON ME INC. 125 HELEN STREET S.PLAINFIELD NJ 07080 908-791-0555 Read all instructions before assembling crib. Save instructions for future use. Adult assembly required. Small parts may present choking hazard prior to assembly. Enclosed please find simple step-by-step instructions to help you quickly assemble your products.Before you begin we recommend that you following the steps below: 1.Please read the instructions thoroughly. 2. Identify all parts and hardwares 3.
PAGE 2
WARNING ! · FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. · READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR FUTURE USE. ANY MATTRESS USDED IN THIS CRIB MUST BE AT LEAST 37-3/4 INCHES BY 23-3/4 INCHES WITH A THICKNESS NOT EXCEEDING 2 INCHES. · CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR SHARP EDGES BEFORE AND AFTER ASSEMBLY.A FREQUENT CHECK SHOULD BE MADE DURING USE.
PAGE 3
CONNECTION HARDWARE a: 1-1/5” Allen head bolt (14 pcs) b:Wood dowels (12pcs) c:Allen wrench (1pc) e:Barrel nuts (14 pcs) f: 3/4” Allen head bolt (4 pcs) i:Knob (3pcs) j:Shelf support (4pcs) d:3” Allen head bolt (4pcs) g: 2-1/5” Allen head bolt (10 pcs) h:1-1/5” Screw (3 pcs) k:Washer (2pcs) l:Bolt (2pcs) m:Belt (1pc) r. Metal connetion (4pcs) n:Tip over restraints (1pc) s.
PAGE 4
Changer front bar I:Changing surface (1pc) K:Changer bottom shelf (1pc) F G F: Top (1pc) G: Middle (1pc) H:Bottom (1pc) J:Changer middle panel H L:Changer left side (1pc) M:Left back leg (1pc) N:Left board (1pc) O:Left front leg (1pc) Q:Back rail bottom (1pc) R:Wooden mattress base(1pc) Drawer T:Front panel (3pcs) U:Left side panel (3pcs) V: Right side panel (3pcs) W:Back panel (3pcs) X:Bottom panel (3pcs) Y:Changer middle shelf (1pc) P:Back top rail(1pcs) S:Front rail bottom (1pc) Z1:Smalll p
PAGE 5
CRIB ASSEMBLY STEP 1 g Attach The changer back(B&C) , and The changer middle(D&E) , and The changer front (F,G,&H) toThe changer right side (A) using wood dowels (b), bolts (a),bolts (g) and barrel nuts(e) by allen wrench (c) . B e A D F a C Model shown is example only. Styles may vary . H STEP 2 B Lay down the assembled parts on the floor . Slide The changing surface (I) into the groove in (D) along the groove between (B) and (G) .
PAGE 6
STEP 3 B q Attach The changer back (B&C) and The changer middle (D&E) and The changer front (F,G&H) to The changer left side (L) using wood dowels (b),bolts (a) and bolts (q) by allen wrench (c) . q b I b F J L b H c STEP 4 Model shown is example only. Styles may vary . d e Attach left back leg (M) and left front leg (O) to left board (N) using bolts (d) and barrel nuts (e) . e d e e Model shown is example only. Styles may vary .
PAGE 7
STEP 5 b q Attach The top rail (P) and the bottom rail (Q) to The changer side (L) and left headboard using wood dowels(b),bolts(q&g) and barrel nuts(e) by allen wrench. q g e b g g e g e e M g e Model shown is example only. Styles may vary . STEP 6 Attach metal connection(r) to the wooden mattress base(R) by using bolts(s) and nuts(t) with wrench. Position the wooden mattress base (R) to a selected position on legs.
PAGE 8
STEP 7 Z2 g g e S g g e Attach The bottom front rail (S) to The changer side (L) and the left head board using bolts (g),barrel nuts (e) and allen wrench (c) .Put the mattress(Z2) into the bed. Model shown is example only. Styles may vary . STEP 8 Attach left side panel (U) & right side panel (V) to back panel (W) by inserting cross screw (p) into the holes on left side panel (U) & right side panel (V) . DO NOT tighten all . p p V p p Model shown is example only. Styles may vary .
PAGE 9
STEP 9 Slide the bottom panel (X) painted side up , into grooves of the left side panel (U) and the right side panel (V) . In the end , insert the bottom (X) into the groove of back panel (W) . Model shown is example only. Styles may vary . STEP 10 h T i p p T p p Attach the knob (i) to the front panel (T) by screw (h) . Attach the front panel (T) to the left side panel (U) and the right side panel (V) by inserting cross screws (p) into the holes on left side panel (U) & right side panel (V) .
PAGE 10
STEP 11 Insert the shelf supports (j) in the holes in the posts of changing table. Then place the changer middle shelf (Y) inside the shelf support. Tighten the screws in the shelf supports (j) . j j j j Y Model shown is example only. Styles may vary .
PAGE 11
STEP 12 1.Slide the drawers into rails on head board (A&L) . 2.Assembly the belt (m) to the changer side (A&L) using washer(k) and bolt(l). 3.Add the pad (Z1) . 4.Put the child on the pad,then insert safty restraint system of the tape across child's waist. The tightness can be adjusted by increasing the tension of the tape. 5.Put the big pad (Z2) into the crib.
PAGE 12
Converting crib to a day bed You have the option to convert crib to a day bed 1:Remove the front rail bottom(S) 2:Install the Wooden mattress base (R) in its lowest position. R Model shown is example only. Styles may vary .
PAGE 13
Converting crib to a twin bed II Conversion kit is sold separately You have the option to convert crib to a twin bed II. 1:Use the back rail as the headboard of twin bed II. 2:Connect the left foot platform and the right foot platform to the rail which are not included and sold separately. 3:Connect the assembled parts and headboard of twin bed to the kits ( legs, long rails,and hardware ) which are not included and sold separately.
PAGE 14
FURNITURE TIPPING DETERRENT HARDWARE HOW TO LOCK Tipping furniture may injure young children. Use of this tipping restraint hardware is highly recommended. When properly instated this hardware could provide protection against the unexpected tipping of furniture due to improper use. WARNING This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent improper use of any potentially hazardous product. 1.