PRIME SHOWER ENCLOSURE, BASE & BACKWALL INSTALLATION INSTRUCTIONS Wall Profile with Flange STEP 1: Shower Base Installation Instructions OR STEP 2: Shower Backwall Installation Instructions STEP 3: Shower Door Installation Instructions ! CHOOSE the APPROPRIATE MANUAL for your model version Wall Profile without Flange Wall Profile WITH Flange: PRIME Manual Ver 1 Rev 3 122015 OR Wall Profile WITHOUT Flange: PRIME Manual Ver 2 Rev 1b 032019 For more information about DreamLine® products please visit
©2018 DreamLine. All Rights Reserved SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice for the purpose of product improvement and customer experience. Please refer to the model’s web page on DreamLine.com for the latest technical drawings, installation manuals, warranty information or additional product details.
©2018 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the parts are included in the package by checking off the components on the parts list.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Shower Base Cross Section Diagram Finished Wall Shower Base Cement board (2"×4") Stud Mortar Drain* * not included This product should be installed by someone familiar with the construction requirements for this type of project and the care necessary for the safe installation and operation of the product.
©2018 DreamLine. All Rights Reserved Shower Base Installation - Preparation 1. Ensure that the floor and the studs are at right angles. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings and tables in this installation manual for the drain location.
©2018 DreamLine. All Rights Reserved 2. Install the shower drain (NOT INCLUDED) according to the drain installation manual (supplied with the drain). (Fig 2) Fig 2 3. Place the tray into the designated position so that the Drain cutout drops around the Drain Pipe and butt the Shower Base up against the studs. (Fig 3) Lower the base over the drain pipe and set it into place against the studs.
©2018 DreamLine. All Rights Reserved 4. Level the tray and place marks on the studs above the upper edge of the tile flange. (Fig 4) Level base in two directions Fig 4 5. Mix the bedding material (Mortar, cement-sand mix, etc.) Concrete or plaster is not recommended. Apply enough bedding material to support the entire bottom of the shower base. This will add additional stability and prevent the base from shifting position.
©2018 DreamLine. All Rights Reserved 6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic base and/or back walls: wipe them off after each use with a soft cloth. To clean the acrylic base or back walls use non-abrasive sprays or cream-based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2018 DreamLine.
QWALL – 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to your model’s web page on BathAuthority.com Please read these instructions carefully before installing.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Acrylic Shower Wall Components”.
Detailed Diagram of Acrylic Shower Wall Components 2 1 3 4 5 6 7 8 Packing List 01 Side panel 2pcs 05 Glass shelf 2pcs 02 Corner cover 1pc 06 Wall anchor 11pcs 03 Decorative edge molding 2pcs 07 Countersunk screw ST4.2×40 11pcs 04 Shelf bracket 6pcs 08 Decorative cover 5pcs NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference.
Preparation for Installation of Side Panel ATTENTION: If you are installing a shower enclosure with a wall profile, you can hide the edge of the Side panel (01) behind the wall profile. Side Panel 1 Wall Profile Wall See Fig. 1 for details. Side Panel 2 Wall Profile Wall Fig. 1 1. Place a mark on the walls with a distance of 1” (one inch) from the corner and draw a plumb vertical line from top to bottom. See Fig. 2 for details. 1 2 1" 1" Fig.
2. Measure the walls of the shower from the 1” (one inch) line in the corner (from Step. 1) to the points where you want Side panels (01) to end. The distances are “D1” and “D2”. D1 D2 D1 NOTE: “D2” Shows wall with the fixture. See Fig. 3 for details. Fig. 3 3. Determine the position of both Side panels (01). NOTE: a) The narrow edge of the Side panels fits behind the corner cover and cannot be trimmed. b) The wide edge of the Side panel can be trimmed to the size of your measurements from step 2.
4. Place the Side panel (01) on a flat piece of plywood or particle board. Use a sharp industrial knife and a Tsquare to score along the marked wide ends of the Side panel and continue scoring until you have fully cut through the panel. See Fig. 5 and Fig. 6 for details. 1 2 Fig. 5 D1 D2 Fig.
5. Take exact measurements of the fixture on the wall: • • 1" D2 A from the 1” (one inch) line in the corner of the shower to the fixture: (A, B, C) from the bottom of the wall of the shower to the fixture: (E, F). See Fig. 7 for details. C E B F Fig. 7 6. Determine which Side panel (01) will be installed on the side wall with the fixture. Mark the fixture location on the Side panel according to the measurements taken in Step. 5. A D2 See Fig. 8 for details. E F B C Fig.
7. Drill the holes for the fixtures in the Side panel (01) using the proper diameter saw bit or a handheld jig saw. D2 See Fig. 9 for details. Fig. 9 Acrylic Side Panel Installation Instruction 8. Attach the Corner cover (02) to the corner of the shower and mark the drilling holes through the predrilled holes in the Corner cover. Move aside the Corner cover, Drill the holes using Ø5/16” drill bit and insert the Wall Anchors (06). See Fig. 10 and Fig. 11 for details. 1 2 3 4 Ø5/16" Fig.
Fig. 11 9. Mount the Corner cover (02) to the corner of the shower using the Countersunk screws ST4.2×40 (07). Do not fully tighten the screws at this time; leave them loose for further installation. 1 See Fig. 12 and Fig. 13 for details 2 Fig.
Fig. 13 10. Apply the sealant to the entire surface of the reverse side of the Side panel (01). Also, apply the sealant around the drilled holes. See Fig. 14 for details. Fig.
11. Slide the narrow edge of the Side panel (01) behind the Corner cover (02). Align trimmed edge of the Side panel (from Step. 4) with the marked line on the wall (in Step. 2) and push the Side panel against the wall. NOTE: Make sure the drilled holes on the Side panel are also aligned with the fixtures on the wall. 1 2 See Fig. 15 for details. Fig. 15 12. Apply sealant to the entire surface of the reverse side of the other Side panel (01). See Fig. 14 for details. 1 13.
14. Once Side panels (01) aligned, fasten tight the Corner cover (02) to secure the Side panels. Cover the screw holes with the Decorative cover (08). 1 See Fig. 17 for details. 2 Fig. 17 ATTENTION; Prior to the next step, please be sure the part of the wall for installation of the Decorative edge molding (03) is clean, dry and free from soap, oil and any construction debris. 15.
16. Apply caulk along the top edge of the Side panels (01) and along the connection of the bottom edges of the Side panels with the Shower base. See Fig. 19 for details. ATTENTION: Installation of “QWALL-4” Acrylic shower wall is complete. If you want to install Glass shelves (05) to your Shower, follow to the next step. Fig. 19 Glass Shelves Installation Instruction 17. Determine the desired height for the Glass shelves (05) and mark the locations on the wall.
18. Mark the location for the Shelf brackets (04) according to the measurements in Fig. 20 and Fig. 21.1. Drill the holes using Ø5/16” drill bit and insert the Wall anchors (06). See Fig. 21 for details. 3 1/2" 3 1/2" 3 1/2" 1 Ø 5/16" 2 3 Fig. 21 1 19. Mount the Shelf brackets (04) to the wall using the Countersunk screws ST4.2×40 (07). NOTE: the padded set screw of the Glass bracket should be facing down.
Fig. 23 Product maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. Acrylic cleaning procedure: Acrylic should be cleaned with warm water and a clean, non-abrasive cloth. If desired, a mild, non-abrasive detergent may also be used.
TEL: 866-731-2244 FAX: 866-857-3638 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Back Wall please visit www.BathAuthority.
PRIME SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to your model’s web page on DreamLine.com Model #s SHEN-7031310 SHEN-7031310-FR SHEN-7034340 SHEN-7034340-FR SHEN-7036360 SHEN-7036360-FR 01= Chrome FR= Frosted Glass Please read these instructions carefully before installing.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Required Caulk Tape Measure Level “PRIME” Enclosure Ver.1 Rev.
Detailed Diagram of Shower Enclosure Components 7 8 1 9 2 3 5 4 10 11 12 6 13 14 15 16 17 Packing List 01 02 03 04 05 06 07 08 09 Wall profile Glass profile Guide rail Glass door Stationary glass Handle Magnetic strip Anti-water strip (2 long, 2 short) Single side strip 2pcs 2pcs 2pcs 2pcs 2pcs 2pairs 1pair 4pcs 2pcs 10 11 12 13 14 15 16 17 Truss head screw ST4.2×40 Round head screw ST4.2x25 Round head screw ST4.2x10 Flat head screw ST4.
Shower Enclosure Installation 1. Fasten the bottom Guide rail (03) to the Glass profiles (02) with the Round head screws ST4.2x25 (11). See Fig. 1 for details. TIP: Apply a small amount of wax or liquid soap to the screws to make installation easier and to prevent stripping the screws while screwing the Glass profiles (02) to the Guide rails (03). Fig. 1 2.
3. Insert the Single side strips (09) in-between the Stationary glass (05) and the Glass profiles (02) using a wooden shim or plastic blade. The strips should be inserted from the side that will face inside the shower. ATTENTION: Do not use a screwdriver or other metal objects to push in the strips to prevent scratching or damaging the glass and aluminum. See Fig. 3 for details. 4.
6. Move the finished frame to the designated position on the shower base or threshold and push it tight to the walls. If the walls are out-of-plumb, make adjustments by slightly pulling the Wall profiles (01) out of the Glass Profiles (02). Use a level to adjust the frame into a plumb, vertical position on both walls. See Fig. 5 for details. NOTE: The installed unit may not sit perfectly centered on the threshold, depending on the thickness of the finished wall treatment used.
8. Fasten the top and the bottom Wheel assemblies (17) to the Glass doors (04). The top wheels can adjust the door level with the adjustable bolt and lock nut. The bottom wheel has a press button to allow installation of the wheel into Guide rail (03). Note: The lock nut of the upper wheel (Fig 7.1) and the press button of the bottom wheel should be pointing up. 1 4 inside 2 5 3 6 See Fig. 7 & 8 for details. NOTE: DO NOT install the handles onto the door glass until instructed to do so.
1 10. Install the Handles (06) onto the Glass doors (04). Press the Anti-water strips (08) onto the vertical edges of the Stationary glass (05) and both vertical edges of the Glass doors (04) (the shorter strips attach to the panel glass and the longer strips onto the doors). Press the Magnetic strips (07) onto the vertical edges of both Glass doors (04) for a tight seal. inside 2 door See Fig. 9 for details. panel 3 door door Fig. 9 11.
12. Apply a good quality mildew-resistant silicone sealant along the profiles and guide rails; on the seams between the bottom guide rail and the profiles as well as along the shower base or threshold from the inside of the shower area. You may also apply silicone along the outside if you choose. See Fig. 11 for details. Allow 24 hours for the silicone to fully cure before using the shower. Follow the safety guidelines from the Sealant manufacturer concerning application, proper ventilation and cure time.
TEL: 866-731-2244 FAX: 866-857-3638 DreamLineWWW.DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit www.DreamLine.
PRIME ® dNSTRUCTIONS e e SHOWER ENCLOSURE INSTALLATION I n v i r L e s m e PLEASE REVIEW THIS ENTIRE MANUAL PRIOR TO INSTALLATION a R e Dr ghts © Ri All d e e in erv L s m e a R e r s D ght © Ri All ® MODEL #s SHEN-7031310-## SHEN-7031310-##-FR SHEN-7034340-## SHEN-7034340-##-FR SHEN-7036360-## SHEN-7036360-##-FR ## = finish 01 - Chrome 04 - Brushed Nickel FR - Frosted Glass IMPORTANT! DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice for the purpose of
d e e n v i r L e s m e a R e Dr ghts © Ri All ® Record the following purchase information for your records or in the event you need to contact DreamLine®: Purchase Order Number Store/Vendor Purchased From Installation Date OD Number (optional) Installed By: SKU Number PRIME Shower Enclosure Manual Ver 2 Rev 1b 03/2019 *found on the shipping box or label if available.
Section Title Warnings and General Preparation Model Specific Preparation Adjustable Wall Profile System Tools Detailed Diagram of Shower Door Components Parts List Installation Steps Top and Bottom Roller Assembly Installation Handle and Vinyl(s) Installation Decorative Cover with Washer Installation Product Maintenance Troubleshooting Factory Parts Information d e e n v i r L e s m e a R e Dr ghts © Ri All ® d e e n v i r L e s m e a R e Dr ghts © Ri All Symbol Legend ® TIP TIP - for ease of installat
©2019 DreamLine® All Rights Reserved WARNING DISCLOSURE STATEMENT IMPORTANT d e e n v i r L e s m e a R e Dr ghts © Ri All • DreamLine® reserves the right to alter, modify or redesign products any time without prior notice for product improvement and customer experience. Please refer to the model’s web page on DreamLine.com for the latest technical drawings, installation manuals, warranty information or additional product details.
©2019 DreamLine® All Rights Reserved Model Specific Preparation 1” Out-of-Plumb Adjustment; Verify threshold and walls with a level Threshold must be level d e e n v i r L e s m e a R e r s D ght © Ri l l A ±0.0 ® 1” minimum flat threshold ±0.0 ! ! NOTE DO NOT attach the handle and/or towel bar to the glass until instructed to do so. DO NOT attempt to use the handle/towel bar to lift the glass during installation. This may result in damage to the glass and/or serious injury.
©2019 DreamLine® All Rights Reserved Adjustable Wall Profile System Glass Profile ! Wall Profile The Glass Profiles can be adjusted within the Wall Profiles for overall width or to correct for out-of-plumb conditions within the model size. ® Screw them together after making final adjustments. d e e n v i r L e s m e a R e Dr ghts © Ri All Glass Profile Wall Profile 1” m ax d e e n v i r L e s m e a R e Dr ghts © Ri All ® ST4.
©2019 DreamLine® All Rights Reserved Tools Tape Measure Level Phillips Screwdriver Pencil d e e n v i r L e s m e a R e Dr ghts © Ri All Silicone ® Power Drill Drill Bit Ø5/16" (8mm) Safety Glasses Painter’s Tape TIP Razor Knife Drill Bit Ø3/16" (4mm) Drill Bit Ø1/8" (3mm) Hacksaw Work Gloves Professional-grade Glass suction cup Soft Head Hammer Mitre Saw Extender Driver Bit #2 Phillips Driver Bit To be sure that the correct model size has been ordered.
©2019 DreamLine® All Rights Reserved Detailed Diagram of Shower Door Components 03 07 ® 14 d e e n v i r L e s 12 m e a R e ts r D 17a © Righ 08a All 01 10 15 06 08b 05 04 11 09 d e e n v i r L e s m e a R e Dr ghts © Ri 17b All 02 ® PRIME Shower Enclosure Manual Ver 2 Rev 1b 03/2019 13 16 6
©2019 DreamLine® All Rights Reserved Parts List 01 02 03 d e e n v i r L e x2 x2 s m e a R e Dr ghts © R05i 06 l Al ® Wall Profile 04 Door Glass x2 07 Push-in Glazing Vinyl Inline Panel Glass x2 08a x2 08b ® Vertical Vinyl Seal (for inline panel) ST4.
©2019 DreamLine® All Rights Reserved Parts List 12 13 14 d e e n v i r L e x4 x4 s m e a R e Dr ghts © R16i All ® ST4.0x10mm Pan Head Screw 15 Wall Anchor 8mm (5/16”) ST4.
©2019 DreamLine® All Rights Reserved 1 Installation Steps d e e in erv L s m e a R e r s t D gh © Ri All ® d e e in erv L s Fig 1 m e a R e r s t D gh © Ri l l A ® TIP Add liquid soap, wax, or lubricant to screws prior to attaching the Glass Profiles (#02) to the Guide Rails (#03). Use a low setting on the power drill, to prevent stripping the screws.
©2019 DreamLine® All Rights Reserved 2 d e e in erv L s m e a R e r s t D gh © Ri All ® d e e in erv L s m e a R e r s t D gh © Ri Fig 2ll A ® Parts Needed 03 11 x1 PRIME Shower Enclosure Manual Ver 2 Rev 1b 03/2019 Tools Needed x4 10
©2019 DreamLine® All Rights Reserved 3 d e e in erv L s m e a R e r s t D gh © Ri All ® NOTE d e e Fig in erv 3 L s m e a R e r s t D © 2 Righ l l A ® The holes in the Wall Profiles (#01) are off-center and must line up with the corresponding holes in the Glass Profiles (#02).
NOTE 1 3 ©2019 DreamLine® All Rights Reserved 4 Before marking the holes for drilling, confirm that: ◻ the assembled frame is tight to the threshold ◻ the Wall Profiles (#01) are tight to the walls ◻ the frame is level d e e in erv L s m e a R e r s t D gh © Ri All ® 2 4 Ø3/16” Drill Bit d e e in erv L s m e a R *see NOTE e r s t D gh © Ri l l A Fig 4 ® NOTE If a stud is present behind the wall, drill a hole using a Ø3/16” drill bit and do not use wall anchors.
©2019 DreamLine® All Rights Reserved 5 1 2 3 d e e n erv i L bottom s m e a R e r s t D gh © Ri All 5 6 ® 4 ST4.0×55 Overhead View ST4.0×55 wall wall Fig 5 TIP d e e in erv L s m e a R e r s t D gh © Ri l l A Extender Driver Bit recommended for the installation of these screws.
©2019 DreamLine® All Rights Reserved 6 Apply a thin bead of silicone caulk to the bottom Guide Rail (#03) when setting the Inline Panel Glass (#05) in place. TIP d e e in erv L s m e a R e r s t DFig 6a gh © Ri All NOTE inside ®For models with Frosted glass, install the textured (Frosted) surface facing towards the inside of the shower.
©2019 DreamLine® All Rights Reserved 7 inside d e e in erv L s m e a R e r s t D gh © Ri All inside ® d e e in erv L s m e a R e r s t D gh © Ri l l A Fig 7 ® Begin installing the Push-in Glazing Vinyl (#09) from the bottom Parts Needed ! To prevent scratching or damaging the glass and aluminum, DO NOT use a screwdriver or other metal tool to install the Push-in Glazing Vinyl (#09). Use a plastic putty knife or similar if necessary.
©2019 DreamLine® All Rights Reserved 8 d e v ® e r n i L e s m e a sR e r D ght © Ri All Top Wheels Faces Up inside Faces Down Button faces up d e e in erv L s m e a Fig 8 R e r s t D gh © Ri l l A ® NOTE Bottom Wheels inside The lock nut on the Top Roller Assembly (#17a) and the push-button on the Bottom Roller Assembly (#17b) should both be pointing up for easier access. DO NOT overtighten the Roller Assemblies (#17a/17b).
©2019 DreamLine® All Rights Reserved 9 1 2 d e e in erv L s m e a R e r s t D gh © Ri All ® 3 4 adjust inside d e e in erv L s m e a R e r s t D gh © Ri l l A Fig 9 NOTE ® Adjust the Top Roller Assemblies (#17a), if necessary, for smoother operation. Tools Needed ! Use caution not to bang the door glass together during installation. Install the Magnetic Vinyl Seals (#07) onto the door glass before fully closing the doors.
©2019 DreamLine® All Rights Reserved Handle and Vinyl Installation 10 d e e in erv L s m e a R e r s t D gh © Ri All ® door inside panel door door door inside inside outside panel d e e in erv L s m e a R e r s t D gh © Ri l l A Fig 10 ® Parts Needed 06 07 x2sets PRIME Shower Enclosure Manual Ver 2 Rev 1b 03/2019 Tools Needed 08a x1pair 08b x2 x2 18
! 1 ©2019 DreamLine® All Rights Reserved 11 DO NOT drill the profiles throughout, ONLY through the first layer of the Wall Profile (#01) and Glass Profile (#02). 2 ll wa 3/4” d e e in erv L s all m e a R w e r s t D gh © Ri All ® Ø1/8” inside inside 3 4 ll wa ll wa inside inside d e e in erv L s m e a R e r s t D gh © Ri Fig 11 l l A ® ST4.
©2019 DreamLine® All Rights Reserved 12 NOTE The surfaces need to be clean and free of debris before applying silicone. ® d e v e r n i L e s m e a sR e r D ght © Ri All 24 Hours d e e in erv L s m e a R e r s t D gh © Ri l l A ® Fig 12 ! Tools Needed Allow 24 hours for the silicone caulk to cure before using shower.
©2019 DreamLine® All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could permanently scratch or dull the surface.
©2019 DreamLine® All Rights Reserved Troubleshooting Problem/Symptom Suggested Solution •Check all shipping/packaging material for missing parts/components. •If not found, contact DreamLine Customer Support [1-855-831-2126] to order Missing Parts factory part replacement. •Inspect the Magnetic Vinyl Seal (#07) for proper installation so that the Magnetic Strike Vinyl (#07) is not creating a tight magnets attract and create a tight seal. seal. •See Step 10 for an image of the correct installation method.
©2019 DreamLine® All Rights Reserved Factory Parts Information d e e in erv L s m e a R e r s t D gh © Ri All PRIME 31x31 SHEN-7031310 ITEM # 01 FACTORY PART NUMBER FACTORY PARTS INFORMATION ITEM DESCRIPTION QTY 04183011-1830 / 04183041-1830 Left or Right Wall Profile 2 pcs 04002011-1830 / 04002041-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 04001012-1280 / 04001042-1280 Top or Bottom Guide Rail (curved) 2 pcs 07550009 Roller Stopper (pre-attached to #03) 8 pcs 092102 ST
©2019 DreamLine® All Rights Reserved Factory Parts Information d e e in erv L s m e a R e r s t D gh © Ri All PRIME 34x34 SHEN-7034340 ITEM # 01 FACTORY PART NUMBER FACTORY PARTS INFORMATION ITEM DESCRIPTION QTY 04183011-1830 / 04183041-1830 Left or Right Wall Profile 2 pcs 04002011-1830 / 04002041-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 04001012-1432 / 04001042-1432 Top or Bottom Guide Rail (curved) 2 pcs 07550009 Roller Stopper (pre-attached to #03) 8 pcs 092102 ST
©2019 DreamLine® All Rights Reserved Factory Parts Information d e e in erv L s m e a R e r s t D gh © Ri All PRIME 36x36 SHEN-7036360 ITEM # 01 FACTORY PARTS INFORMATION FACTORY PART NUMBER ITEM DESCRIPTION QTY 04183011-1830 / 04183041-1830 Left or Right Wall Profile 2 pcs 04002011-1830 / 04002041-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 04001012-1534 / 04001042-1534 Top or Bottom Guide Rail (curved) 2 pcs 07550009 Roller Stopper (pre-attached to #03) 8 pcs 092102 S
d e e in erv L s m e a R e r s D ght © Ri All ® d e e in erv L s m e a R e s r D ght © Ri All ® TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.