Flex Shower Enclosure (34x46, 34x58) & Base SHOWER ENCLOSURE & BASE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
©2018 DreamLine. All Rights Reserved SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT! DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
©2018 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Shower Base Installation - Preparation 1. Ensure that the floor and the studs are at right angles. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings and tables in this installation manual for the drain location. 90° 90° 90° See Fig. 1 and Fig. 2 for details.
©2018 DreamLine. All Rights Reserved 2. Install the shower drain (NOT INCLUDED) according to the drain installation manual (supplied with the drain). See Fig. 3 for example Fig. 3 3. Place the tray into the designated position so that the Drain cutout drops around the Drain Pipe and butt the Shower Base up against the studs. See Fig. 4 for details. Lower the base over the drain pipe and set it into place against the studs. Fig.
©2018 DreamLine. All Rights Reserved 4. Level the tray and place marks on the studs above the upper edge of the tile flange. See Fig. 5 for details. Level base in two directions Fig. 5 5. Mix the bedding material (Mortar, cement-sand mix, etc.) Concrete or plaster is not recommended. Apply enough bedding material to support the entire bottom of the shower base. This will add additional stability and prevent the base from shifting position. See Fig. 6 for details. Mortar Fig.
©2018 DreamLine. All Rights Reserved 6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
©2018 DreamLine. All Rights Reserved Fig.
©2018 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic base and/or back walls: wipe them off after each use with a soft cloth. To clean the acrylic base or back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.
FLEX ENCLOSURE SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
Wall profile Return panel Wall profile Expandable rail Return panel glass Stationary panel glass Corner profile Door Glass Wall profile* do or ( *not used with corner profile) ur ret l ne a np Expandable rail USE THE INSTALLATION MANUAL THAT IS PACKAGED WITH THE FLEX DOOR TO ASSEMBLE AND INSTALL THE DOOR SECTION. ! USE THIS MANUAL TO ASSEMBLE AND INSTALL THE RETURN PANEL AND FOR THE ENCLOSURE DIMENSIONS NOTE: This model is reversible for left or right-hand installation.
Table of Contents Section title Page # Shower Enclosure Diagram Preparation Tools 4 Diagram of Shower enclosure components Parts List 8 9 Installation Steps 10-18 Vinyl Seals 17 Product maintenance 19 5 ©2018 DreamLine.
Shower Enclosure Plan RIGHT-HAND RETURN PANEL SHOWN AS AN EXAMPLE SHDR-2230300-RT-01 30-1/2” 32-1/2” min to 36-1/2” max 28-1/2 “min to 32-1/2” max 1-1/2” minimum threshold required 34-1/2" SHDR-2234580-RT-01 34-1/2" 1-1/2” minimum threshold required 56-1/2” min to 60-1/2” max ©2018 DreamLine.
This shower enclosure requires a minimum 1-1/2” wide threshold for installation. Compare the overall outside dimensions of the shower enclosure model size as shown on the “Shower Enclosure Plan” with the finished threshold to ensure proper fit prior to beginning installation. -1/ 32 2 “m -1/ in 44 2” m to 32 -1/ in -1 56 2” m to 36 /2” m -1/ i -1/ ax 2” n to 48 2” m mi nt a o 6 1/2” x 0-1 max /2” ma x 1-1/2” minimum threshold required 2” -1/ 2” 0 3 -1/ 34 ©2018 DreamLine.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with the packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Level Power Drill Tape Measure Pencil Silicone Drill bit Ø5/16" (8mm) Phillips Screwdriver Drill bit Ø=1/8" (3mm) Razor Knife Hammer Top Middle Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered. Bottom Threshold must be level. W Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts. ! ©2018 DreamLine.
Detailed Diagram of shower door components 10 1 3 11 2 4 5 9 6 Doo r 7 13 tur Re l ne a np ©2018 DreamLine.
Parts List Door packing List 01 02 03 04 05 Wall profile* Door assembly Wall anchor Pan head screw ST4.2×10 Truss head screws ST4.2×40 2pcs* 1set 8pcs 10pcs 8pcs 06 07 08 13 Decorative cover Flanged anti-water strip Bottom anti-water strip Handle 10pcs 1pc 1pc 1pc * Only one Wall Profile is used with the shower enclosure installation Return panel packing List 6pcs 3pcs 1pc 10 11 Corner profile Return panel wall pofile 1pc 1pc ©2018 DreamLine. All Rights Reserved 04 Round head screw ST4.
Installation steps 1. The width of the shower enclosure model is adjustable and can be adjusted to the size of your shower base or custom threshold. Mark the position of the Wall profile (#01) and the Return Panel Wall Profile (#11) on the wall according to the model size and dimensions provided in the size table below. Wall Profile Return Profile Place the Wall Profile (#01) and the Return Panel Wall Profile (#11) onto the threshold against the finished wall. Use a level to adjust to plumb.
2. Mark the holes on the wall for drilling through the pre-drilled holes in the Wall Profile (#01). Drill the holes into the wall using a Ø 5/16 drill bit and insert the Wall Anchors (#03). 3 2 1 Ø 5/16" 4 6 5 Apply silicone to the back surface of the Wall Profile (#01 ) and place it back in position on the wall. Attach the Wall profile (#01) to the wall with the Truss head screws ST4.2×40 (#05). (Fig 2) 3.
USE THE INSTALLATION MANUAL PACKAGED WITH THE FLEX DOOR TO ASSEMBLE AND INSTALL THE DOOR SECTION. (Fig 4) 28” and 32” model 42”, 48” and 60” model Pre-assembled Assembly required 4. Move the Door assembly onto the threshold ©2018 DreamLine. All Rights Reserved and slide the Stationary glass profile into the Wall profile (#01).
5. Slide the Corner profile (#10) over the aluminum edge of the Return Panel Assembly (#09). Drill Ø 1/8” holes through the predrilled holes on the Corner profile (#10) into the aluminum profile on the Return Panel Assembly (#09). Secure the Corner profile (#10) to the Return Panel Assembly (#09) with the Pan head screws ST4.2×10 (#04). (Fig 5) 1 e insid 2 Ø 1/8" ide outs 3 Fig 5 ©2018 DreamLine. All Rights Reserved 6.
7. Extend the width of the Door assembly (#02) by sliding the top and bottom expanding rails toward the Corner profile (#10). Insert the Door Glass side into the Corner profile (#10). (Fig7) NOTE: The maximum adjustment of the Expanding rails is 3”. Do not expand the rails more than 3”. 1 2 3 4 Fig 7 8. Make sure the Door assembly (#02) is fully extended into the Wall profile (#01) and the Corner Profile (#10). Adjust top and bottom Expanding rails to the same length, making the door area square.
9. From inside of the shower, drill holes into the top and bottom Expanding rails through the predrilled holes using an Ø 1/8” drill bit. ATTENTION: Drill only through the first layer of the Expanding rail. Secure the Expanding rails using Pan head screws ST4.2×10 (#04) with the raised white washers. Cover exposed screw heads with Decorative covers (#06). (Fig 9) 1 Ø 1/8” 2 3 5 6 ins ide ins ide Ø 1/8” 4 ©2018 DreamLine.
10. Perform the final adjustments to the Door assembly (#02) and Return panel glass (#09) as necessary. Operate the Door Glass to make sure that the magnetic strips are aligned and make full contact from top to bottom. Drill holes into the aluminum profile of the Door assembly through the predrilled holes in the Wall profile (#01) using an Ø 1/8” drill bit. Drill Ø 1/8” holes into the aluminum profile through the predrilled holes in the Return panel wall profile (#11).
11. Drill holes into the aluminum profile of the Door assembly (#02) through the predrilled holes in the Corner Profile (#10) using an Ø 1/8 drill bit. Secure the Door assembly inside the Corner Profile (#10) using the Pan Head Screws ST4.2×10 (#04) with the raised white washers. Cover the exposed screw heads with the Decorative Covers (#06). (Fig 11) 1 3 2 Ø 1/8” anel np etur r do or ins ide Fig 11 RIGHT-HAND RETURN PANEL SHOWN AS AN EXAMPLE 12.
13. Apply a good quality mildew-resistant silicone along the interior perimeter where the profiles meet the walls and threshold. (Fig 13) ! Allow 24 hours for the silicone to cure before using the shower. ©2018 DreamLine.
Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use with a soft cloth.
For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2018 DreamLine. All Rights Reserved TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.
FLEX 42”x 72“/ 48”x 72“/ 60”x 72” SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
Table of Contents Section title Preparation Tools Parts Diagram of Shower Door Components Parts List Page # 2 3 4 Model Overview 5 6 Installation Steps 7-19 Vinyl Seals 16-17 Product Maintenance 20 FLEX 42x72 / 48x72 / 60x72 manual Ver 1 Rev 3 04/2018 ©2018 DreamLine.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Level Drill bit (Ø=5/16") (8mm) Tape Measure Drill bit (Ø=1/8") (3mm) Phillips Screwdriver Pencil Power Drill Hammer Razor Knife 100% Silicone Top Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered. Threshold must be level. Middle Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts. ! W ©2018 DreamLine.
3 1 Parts Diagram 4 5 15 2 12 6 1 17 13 14 16 8 ©2018 DreamLine.
Parts List Part# DESCRIPTION QTY Part# DESCRIPTION QTY Wall profile 2pcs 12 Magnetic Strike Profile 1pc 2 Panel Glass assembly 1set 13 Handle 1pc 3 Wall anchor 8pcs 14 ST4.2×25 Round head screw 4pcs 4 ST4.2×10 Round head screw 10pcs 15 Top & Bottom pivot Rail 2pcs 5 ST4.2×40 Truss head screw 8pcs 16 Top & Bottom pivot Hardware 2pcs 6 Decorative cap and washer 10pcs 17 Door Glass 1pc 7 Flanged anti-water strip 1pcs 8 Bottom anti-water strip 1pc ©2018 DreamLine.
Model Overview Alluminum wall profile Stationary panel glass assembly Expandable rail Door Glass pa ne l Alluminum wall profile do or ©2018 DreamLine.
Installation steps 1. Insert the Top & Bottom Pivot Rails (#15) into the expandable rails of the Stationary panel Assembly (#02). (Fig 1) SHDR-22427200-01 and SHDR-22487200-01: Insert the end that is closer to the pivot hole SHDR-22607200-01: Insert the end that is farthest from the pivot hole top outside inside outside inside bottom Right hand door installation shown insert this end pivot hole pivot hole do or 23 -5/ 8” 60” model do or 23 ©2018 DreamLine.
2. Attach the Magnetic Strike Profile (#12) to the Top & Bottom Pivot Rails (#15) using four of the ST4.2 x 25 Round Head Screws (#14). (Fig 2) ins ide inside Fig 2 ! ©2018 DreamLine. All Rights Reserved TIP: Apply some wax or dish soap to the screws to make assembly easier and to prevent stripping the screws.
3. Slide both of the Wall Profiles (#01) over the frame assembly. Be sure that the flanges on the Wall Profiles (#01) face in towards the shower. (Fig 3) inside inside pa ne inside l do or are a 4. At this point, the entire assembly can be flipped top to bottom for either left or right hand door installation. However, the flanges on the wall profiles must face into the shower. (Fig 4) Fig 3 pa el pan ne ©2018 DreamLine.
5. Check the threshold of the finished opening to make sure that it is level. (This model does not allow for out-of-level adjustment) (Fig 5) 6. Place the assembly onto the threshold at the desired location and extend the expandable Top & Bottom Pivot Rails (#15) evenly. (Fig 6) Fig 5 1 Right hand door installation shown FLEX 42x72 / 48x72 / 60x72 manual Ver 1 Rev 3 04/2018 ©2018 DreamLine.
7. The opening for the door glass must be square. Measure the top and bottom of the door opening and adjust the Expandable Rails as necessary. Push the Wall Profiles (#01) tight to the walls to compensate for up to 1/2” out-of-plumb per wall. (Fig 7) ! Make sure that the Wall Profiles (#01) are also tight to the threshold and even with the top of the frame assembly. the d mus oor ope t be n squa ing re Fig 7 8. Check that the frame assembly is plumb inside ©2018 DreamLine.
9. Move the frame assembly aside and remove the Wall Profiles (#01). Drill the holes into the walls using a Ø5/16” (8mm) drill bit and insert the Wall Anchors (#03). (Fig 9) 1 3 Ø5/16” (8mm) 2 4 Ø5/16” (8mm) Fig 9 10. Apply a bead of silicone to the back of the Wall Profiles (#01) and the screw holes where the Wall Profiles (#01) will be installed. Attach the Wall Profiles (#01) to the wall using the ST4.2 x 40 Truss Head Screws (#05). Repeat this process for the opposite wall profile.
11. Place the assembly back onto the threshold and into the panel-side Wall Profile (#01) first. (Fig 11) Fig 11 12. Extend the Expandable Rails evenly so that the Magnetic Strike Profile (#12) goes into the opposite Wall Profile (#01) on the door-side of the opening. (Fig 12) 1 ©2018 DreamLine.
13. Check and adjust the door opening for square and make certain that the entire assembly is tight to the threshold. (Fig 13) the d mus oor ope t be n squa ing re Fig 13 14. Install the Top & Bottom Pivot Hardware (#16) into the pivot bushings in the Top & Bottom Pivot Rails (#15). (Fig 14) pivot pivot rotation sid e ©2018 DreamLine. All Rights Reserved out inside pivot bushing (pre-installed in the rails) ! Note: The pivots are packaged as a pair. Check the difference in the rotation direction.
! NOTE: DO NOT install the handle onto the door glass until instructed. DO NOT attempt to lift the glass using the handle. This could result in damage to the glass and/or serious personal injury. Always use an assistant or a professional grade glass suction cup when handling heavy glass. 15. Carefully install the Door Glass (#17) onto the Top & Bottom Pivot Hardware (#16). Make certain that all gaskets are in place to protect the glass. Cover the bolt with the decorative cap.
16. Trim the Bottom Anti-Water Strip (#08) to fit on both sides of the bottom pivot and attach both pieces to the bottom of the Door Glass (#17) (Fig 16) ! NOTE: Measure to the edge of the door and notch the Bottom anti-water strip (#08) with a razor knife to fit around the magnet strip, leaving the bottom deflector intact. Fig 16 do or (Fig 17) do or ©2018 DreamLine. All Rights Reserved 17. Attach the Handle (#13) to the Door Glass (#17).
18. Attach the Flanged Anti-Water Strip (#07) to the vertical edge of the Stationary Panel Glass (#02) with the flange facing into the shower. (Fig 18) inside pa ne l outside pa ne l ©2018 DreamLine.
1 19. Once all adjustments have been made, drill pilot holes from inside of the shower into the Top & Bottom Pivot Rails (#15) through the predrilled holes using an Ø1/8” drill bit. Ø1/8” (3mm) 2 ins ins ide ! ide NOTE: Do Not drill the rails throughout, only through the first layer. Ø1/8” (3mm) 3 Secure the Expanding rails using the Round Head Screws ST4.2×10 (#04) and the raised white washers. Cover the exposed screw heads and washers with the Decorative Caps (#06). (Fig 19) ST4.
21. Apply a good quality mildew-resitant silicone around the interior perimeter along both walls and the threshold. (Fig 21) ! Allow 24 hours for the silicone to cure before using the shower. ©2018 DreamLine.
Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2018 DreamLine.