BARN-DOOR STYLE SLIDER SHOWER DOOR INSTALLATION INSTRUCTIONS PLEASE REVIEW THIS ENTIRE MANUAL PRIOR TO INSTALLATION d e v er s e 3 R 202 ghts © Ri All d e v er s e 3 R 202 ghts © Ri All IMPORTANT! The manufacturer reserves the right to alter, modify or redesign products at any time without prior notice for the purpose of product improvement and customer experience.
d e v er s e 3 R 2 20 ghts © Ri All ClearMax® a specially-formulated coating that prevents the build up of soap and water spots. If your model is treated with ClearMaxTM, nstall the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on requirements for reversibility, the glass may be coated on either one or both surfaces. d e v er I s e 3 R 2 20 ghts © Ri All For best results, squeegee the glass after each use and dry with a soft cloth.
Section Title © 2023 All Rights Reserved Table of Contents Page # Important Product Information 2 Model Specific Preparation 3 Tools 4 Detailed Diagram of Shower/Tub Door Components 5 Parts List Installation Steps d e v r ese 3 R 2 0 s t Measuring and Cutting the 2 Vertical Channel h g © i Setting and Marking the UChannel R l l Installing the UChannel A Determining the Position of the Shower Door 6-7 8-35 9 10 11 12 Marking Rollers and Installing them on the Door Glass 18 Leveling the Gui
WARNING DISCLOSURE STATEMENT IMPORTANT • GENERAL PREPARATION • • The manufacturer reserves the right to alter, modify or redesign products any time without prior notice for product improvement and customer experience. Please refer to the manufacturer’s web page for the latest technical drawings, installation manuals, warranty information or additional product details.
! REQUIRED: 1/4” Out-of-Plumb Adjustment on Panel side only; Verify panel-side wall is within tolerance TIP Threshold must be level .0 ! Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered. d e v er ±0.0 s e 3 R 202 ghts © Ri All 2-1/4” (44mm) ±0 Minimum flat threshold requirement Threshold must be level TIP © 2023 All Rights Reserved Model Specific Preparation This door is reversible.
Tape Measure Level Phillips Screwdriver Painter’s Tape Pencil s Power e 3 R 202 ghts Drill © Ri All Drill bit Drill bit (D=5/16") (D=3/16") Metal File Drill bit (D=1/8") Professional-grade Glass suction cup Carpenter’s Square Silicone d e v er © 2023 All Rights Reserved Tools Screw Gun Extender driver bit Mallet Chop saw or Hacksaw d e v er s e 3 2 ts R 0 2 Verify that the correct model size has been h ordered; measure the finished opening g i TIP before proceeding with©the installation.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Detailed Diagram of Barn Door Slider with Panel 08 01 01 14 3 2 0 2 05 ghts © Ri All d e v er s Re 09 14 01 04 03 07 02 01 03 d e v er s e 3 R 202 ghts © Ri All 26 11 13 12 16 5 © 2023 All Rights Reserved
01 02 UChannel x1 04 © 2023 All Rights Reserved Parts List 03 Stationary Glass x1 rved e s e 3 R 202 ghts © 05Ri All 6a 6b 6b Guide Rail x1 07 Stopper 08 Glass Bracket x1 x2 09 d e v er 11 Dam Strip Cap 6a Guide Rail Bracket and Wall Block x2 s e 3 R 202 ghts © Ri x2 x2 All Roller 10 x1 Door Glass Roller Guard x2 Guide Block x1 12 Dam Strip BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 x1 6
© 2023 All Rights Reserved Parts List 13 14 Vertical Vinyl x2 16 Bumper 19 15 Bumper Vinyl x1 Wall Anchor x1 ST4.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Installation Steps 1 Use a chop saw (or a hacksaw) to cut the stainless steel Guide Rail (#04) from the door end only to fit the finished opening. Fig 1 Measure the finished opening width at the model height of 69”: This will be dimension (W).
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 2 Determining the Position of the Shower Door NOTE The Guide Block (#12) represents the ‘footprint’ of the door. Place it in the desired position on the threshold and mark the front edge. Extend this ‘reference line’ across the threshold to both walls, parallel with the front threshold edge. This will help to accurately install key parts of the shower door in later steps.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Cutting the UChannel to the Height of the Panel Glass 3 NOTE d e v er s e 3 R 202 ghts © Ri All Measure the height of the Stationary Glass (#02) for your shower door model. Measure that same length on the UChannel (#01), mark it, and cut the UChannel using a chop saw with a blade for cutting metal. Fig 3 Parts Needed d e v er NOTE s e 3 R 202 ghts Use a metal file to remove ©cut endRi any burrs from the of the UChannel (#01).
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 4 Setting and Marking the UChannel NOTE Align the outside edge of the U-Channel (#01) with the inside of the mark on the threshold. Use a level to plumb the U-Channel (#01) and mark it’s position on the wall. Mark the holes for drilling through the pre-drilled holes in the U-Channel (#01).
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 5 Installing the UChannel 1 2 d e v er Ø5/16" (**See Drilling Instructions) 3 s e 3 R 202 ghts © 4 Ri All Parts Needed 01 x1 18 x4 17 *Optional Apply silicone to the back of the UChannel d e v er Fig 5 es NOTE 3 2 0the wall:hts R If a stud is present behind 2 drill a Ø3/16”(4mm) hole up to the then use a Ø1/8” (3mm) © Rusing ig stud, bit to pilot the stud, and install the ST4.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 6 Positioning and Marking the Guide Rail Brackets outside inside = 1-1/4" 32mm s e 3 R 202 ghts © Ri All Guide Rail Bracket UChannel d e v er H = Fig 6 68-1/4” (1734mm) top ! NOTE (H)=68 1/4” Note that the bottom of the bracket is thicker than the top and must be installed correctly The Block in the Guide Rail Bracket must be centered in the Bracket (as shown) to allow for vertical adjustment later if needed.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 7 Installing the Panel-side Guide Rail Block (6b) 1 NOTE Mark 2 6b d e v er s e 3 R 202 ghts © Ri All If a stud is present behind the wall: Drill a Ø3/16”(4mm) hole up to the stud. Pilot the stud with a Ø1/8”(3mm) bit. Secure with an ST4.2x55mm Countersunk Screw (#18).
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Installing Stoppers and Guide Rail Bracket Sleeves (6a) on Guide Rail 8 1 A Install panel-side stopper past the hole in the rail. Loosen d e v er s e 3 R ts 202Tighten h © Rig All B Fig 8 Parts Needed 2 NOTE 6a 6b 6b Install the Stoppers (#05) and the Guide Rail Bracket Sleeves (#6a) on both ends of the Guide Rail (#04), making sure the Stopper on the panel side does not block the hole in the Guide Rail.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 9 Dry Fit Panel Glass, Mark Guide Block for Installation NOTE d e v er Carefully dry fit the Stationary Panel Glass (#02) into the installed UChannel (#01), aligning the glass parallel with the front threshold edge.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 10 Remove Panel Glass, Install Guide Block w/out Faceplate 1 ! Leave the Faceplate off the Guide Block until after the Panel Glass is installed. 2 d e v er ** See Drilling Instructions s 3 e 3 R 2 20 ghts © Ri All 4 Parts Needed 12 x1 17 * Optional d e v er Fig 10 s e 3 R 2 ts For installation into a tile threshold over wood, 20 h drill a Ø1/8”(3mm) hole.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Marking the Roller Wheels and Installing them on the Door Glass 11 Inside View 1 Inside Outside Flip Install the Roller Wheels with the temporary mark pointing toward the strike-side wall. d e v er s e 3 R 202 ghts Strike-side © Ri wall l l A Pencil or Erasable Marker High Spot ! Temporary Mark 2 Door Glass This illustration is for reference only. Do not attempt to install the Door Glass yet.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Place Door Glass in Opening, Install Stationary Glass 12 1 2 d e v er 3 s e 3 R 202 ghts © Ri All 1/2” bead/Clear Silicone in UChannel Parts Needed 03 NOTE Place Door Glass (#03) inside opening, facing the correct way for installation d e vNot allow edges of Do r e s e Door Glass (#03) to 3 R 2 0 s t 2 © Righ ! All contact anything as hard as glass or harder. Protect glass edges at all times.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Install Guide Block Faceplate; Install Pinch Vinyl 13 C NOTE A) Install Faceplate with gaskets B) Tighten set screw C) Install caps NOTE d e v er s e 3 R 202 ghts © Ri All C B A The Pinch Vinyl (#22) snaps into place between the Panel Glass and the UChannel on the inside of the shower. Fig 13 Parts Needed 12 ese d e rv 3 R 2 0 s t 2 © Righ All TIP Start from the bottom and work upward. Cut any excess.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 14 Install the Panel-side Guide Rail Bracket Sleeve 1 NOTE Loosen A Loosen the top and bottom set screws. Align the Guide Rail Bracket (Pt 6A) with the installed Block (Part 6B). Slide the Bracket over the Block and tighten only the set screws nearest the wall.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 15 Install Glass Brackets/Connect Panel Glass to the Guide Rail d e v er s e 3 R 2 20 ghts © Ri All Guide Rail Stationary Glass NOTE NOTE: Some parts are hidden or slightly repositioned for clarity. d e v er s 15 e 3 Fig R 202 ghts © Ri Attach the Stationary Glass (#02) to the Guide Rail All (#04) using the Glass Brackets (#07). Leave the NOTE Parts Needed 07 x2 Tools Needed brackets slightly loose for the next step.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 16 Leveling the Guide Rail NOTE Level the Guide Rail (#04) across the opening. If necessary, use the outside set screws on the Guide Rail Bracket (#06) to adjust the level of the Guide Rail (#04) and then fully tighten the Glass Brackets (#07). Fig 16 3 2 0 2 ghts © Ri All se e R d e v er s e 3 R 202 ghts © Ri The Glass Brackets (#07) llwill need to be temporarily loosened to perform A this procedure correctly..
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 17 Marking the Door-Side Guide Rail Bracket NOTE Using the ‘reference line’ on the door-side of the threshold from Step #2, draw a plumb line up the wall on the door side of the opening. To place the Guide Rail Bracket, measure over 1-1/4” into the shower from this line. With the Guide Rail (#04) level, mark the position of the Guide Rail Bracket (#06) on the wall. Fig 17 d e v er s e 3 R 2 20 1g.25h” ts © R1i.75mm All 3 68.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 18 NOTE Installing the Door-Side Guide Rail Bracket Remove the Guide Rail (#04) from the Stationary Panel Glass (#02). Remove the Guide Rail Bracket (#06) from the Guide Rail (#04) and hold it in position on the wall. Mark the hole for drilling and then drill it, using the drilling instructions below. Separate the Guide Rail Bracket (#06) components 6a and 6b.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 19 Re-Installing the Guide Rail and Guide Rail Brackets B 3 2 0 2 ghts © Ri All d e v er s e R A B B d e v er A NOTE s e 3 R 2 ts 19 20 ghFig © RGuide i Rail (#04) for level. If necessary, adjust with Re-check the l Al set screws on the Guide Rail Brackets (#06a/06b) as the outside Tools Needed seen in Step 16 on Page 23.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 20 Dam strip inserts under Panel Glass Installing the Dam Strip and Cap 1 2 d e v er s e 3 R 2 0 s t 2 © Righ All Measure Cut Parts Needed 11 3 4 x1 Apply silicone to bottom of Dam Strip and Cap. d e v er es 3 R 2 20 ghts © Ri l the Dam Strip in place once Tape TIP A l installed until the silicone sets up.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 21 Hanging the Door Glass d e v er s e 3 R 2 0 s t 2 © Righ All Parts Needed Fig 21 ved r e s e 3 R 2 0 s t 2 a Professional-grade © Righ Use Glass suction cup (if available) when handling All 03 TIP x1 Tools Needed heavy glass.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 22 Installing the Roller Guards Apply Threadlock (#20) to the bolt on both Roller Guards d e v er s e 3 R 2 0 s t 2 © Righ All Fig 22 Parts Needed 20 x1 d e v er 09 Leave a 1/16” gap between the Roller Guards and the Guide Rail s e 3 R 2 20 ghts © Ri All x2 Tools Needed 29 © 2023 All Rights Reserved
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 23 Installing the Handle d e v er s e 3 R 202 ghts © Ri All d e v er s e 3 R 202 ghts © Ri All Fig 23 Parts Needed 15 x1 30 © 2023 All Rights Reserved
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 24 Installing the Vinyls Overhead View d e v er s e 3 R 202 ghts © Ri All Outside of Shower d e v er s e 3 R 202 ghts © Ri All Fig 24 Parts Needed 13 x2 14 x1 31 © 2023 All Rights Reserved
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 25 NOTE Adjusting the Roller Wheels (If needed) The discs on the backs of the Roller Wheels have oblong centers and can be rotated to tilt the door glass slightly to create a tight seal with the wall. The temporary marks made in Step 11 (now facing the strike-side wall) indicate the high spot. Fig 25 Inside View d e v er Turning the mark up will raise the door, turning it down will lower it.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 26 Installing the Safestop™ Bumper NOTE To install the Bumper (#16): Remove the 3M Tape backing and position the Bumper (#16) on the threshold behind the U-Channel (#01) on the stationary panel side of the installation.
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 27 Securing the Stoppers ! Cover the shower/tub drain with tape prior to removing the set screws to prevent loss. Position the Panel-side stopper so the door glass makes contact with the stopper and the Bumper (#16) at the same time. Fig 27 NOTE d e v er s e 3 R 202 ghts © Ri All Remove the set screws from the Stoppers (#05) and apply Thread Lock Adhesive (#20) to the threads. Reinsert the set screws into the Stoppers (#05).
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 28 Applying Silicone NOTE Clean all surfaces, then apply a good quality, mildew-resistant silicone where the stationary glass meets the walls and the threshold. Fig 2 28 d e v er s e 3 R 2 20 ghts © Ri All 24 Hours d e v er s e 3 R 202 ghts © Ri All Fig 28 Tools Needed NOTE Allow 24 hours for the silicone to fully cure before using the shower.
© 2023 All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could permanently scratch or dull the surface.
Problem/Symptom © 2023 All Rights Reserved Troubleshooting Suggested Solution Missing Parts •Check all shipping/packaging material for missing parts/components. •If not found, contact the manufacturer to order factory part replacement. Top Guide Rail (#04) was cut too short or was cut from wrong end during installation. •The Top Guide Rail (#04) is pre-cut for the model size, and will be shorter than the model width to allow for the Guide Rail Brackets (#06a and 6b).
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Factory Parts Information 58” x 71” Shower Door BARN DOOR STYLE DOOR 58" x 71" ITEM# 1 2 3 4 5 6a/6b 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 22 FACTORY PARTS INFORMATION FACTORY PART NUMBER ITEM DESCRIPTION 0712X229 UChannel QTY 1 10420059 Stationary Glass 1 10420058 Door Glass 1 Guide Rail 1 Stopper 2 Guide Rail Bracket and Wall Block 2 Glass Bracket 2 Roller 2 Roller Guard 2 0755X068 Dam Strip Cap 1 041000X1-0770S Dam
BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 Factory Parts Information 60” x 72” Shower Door BARN DOOR STYLE DOOR 60" x 72" ITEM # 1 2 3 4 5 6a/6b 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 22 FACTORY PARTS INFORMATION FACTORY PART NUMBER ITEM DESCRIPTION 0712X229 UChannel QTY 1 010420062 Stationary Glass 1 010420063 Door Glass 1 Guide Rail 1 Stopper 2 0702X111 Guide Rail Bracket and Wall Block 2 0702X112 Glass Bracket 2 0732X023 Roller 2 0702X188 Roller Guard 2 0755X
© 2023 All Rights Reserved NOTES BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 39
© 2023 All Rights Reserved NOTES BARN DOOR STYLE SLIDER Installation Manual Ver1a 122023 40
SHOWER DOOR INSTALLATION INSTRUCTIONS PLEASE REVIEW THIS ENTIRE MANUAL PRIOR TO INSTALLATION d e v er s e 3 R 202 ghts © Ri All d e v er s e 3 R 202 ghts © Ri All IMPORTANT! The manufacturer reserves the right to alter, modify or redesign products at any time without prior notice for the purpose of product improvement and customer experience. Please refer to the manufacturer’s web page for the latest technical drawings, installation manuals, warranty information or additional product details.