UNIDOOR PLUS (STYLE G) SHOWER DOOR & GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com STYLE G STEP 1: Install Shower Door STEP 2: Install Panel For more information about DreamLine Shower Doors, Tub Doors and Enclosures, please visit DreamLine.
©2018 DreamLine. All Rights Reserved UNIDOOR/UNIDOOR-LS/UNIDOOR LUX/UNIDOOR PLUS SINGLE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
©2018 DreamLine. All Rights Reserved Style “A” (single door installation shown) with Half-Frosted Glass: NOTE: This model features the Half-Frosted glass option. The textured surface on the door glass should be installed to face outside of the shower. The door glass can be flipped for left or right-hand installation.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Models with Glass-to-Glass Hinge panels: For Glass-to-Glass Hinge Door models: Use the installation manual that is packaged with the Hinge panel glass first.
©2018 DreamLine. All Rights Reserved STYLE A UNIDOOR Single shower door 23”- 30” Refer to detailed diagram on page 12 of this manual to begin the installation.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package(s) by checking off the components on the “Detailed Diagram of Shower Door Components”.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Single Shower Door Assembly and Installation NOTE: The following shower door installation instructions should be used as a general guide and prerequisite to the installation of the UNIDOOR, UNIDOOR-LS, UNIDOOR LUX and UNIDOOR PLUS models. Before you begin the installation, please check your finished opening size. Specific size information can be found on DreamLine.
©2018 DreamLine. All Rights Reserved 2. The Door Glass (01) ships with four 5/8” shims attached to the top (2pcs) and bottom (2pcs). Determine the swing of your door and only remove the shims from the top of the door glass, leaving the bottom shims in place. Set the Door Glass (01) onto the threshold at the desired location and check for level.
©2018 DreamLine. All Rights Reserved 1 TIP: The PVC hinge spacer can also be used as a template to assist with marking the hinge mounting holes. 2 *Only use the PVC hinge spacer to correct for minor out-of-plumb wall conditions. 3 Fig. 4 ATTENTION: As viewed from inside the shower, the hinge plate is very close to the drilled holes in the wall and might get scratched while installing the long screws. Be careful not to scratch the hinge surfaces during installation. (OPTIONAL) 5.
©2018 DreamLine. All Rights Reserved Setting the Adjustable Hinges The Adjustable hinges are pre-set to overclose to 85º and are adjustable up to 90º after the door is installed. Once the door glass is installed, simply loosen the Allen set screws and position the door to the desired closed position. While holding the door in the new closed position, retighten the Allen screws and your door will now self-center to the chosen closed position. 5a.
©2018 DreamLine. All Rights Reserved 5b. The hinges are factory set to 85 degrees. You can change this angle by using the adjustment screws on the hinge plate. (Fig 5b) outside inside Fig 5b 5c. Use the supplied Allen Key to loosen the adjustment screws on the inside hinge plate, adjust the door to the desired angle (90 degrees for example) then retighten the adjustment screws (Fig 5c). Be sure that you create a tight seal with the supplied strike vinyl when the door is in the closed position.
©2018 DreamLine. All Rights Reserved 6. Mount the Handle (02) to the Door Glass (01). (Fig 6) Fig. 6 7. Measure the bottom of the Door Glass (01) from end to end to determine the actual width of the door. Cut the Bottom anti-water strip (07) to the size of your measurement and notch approximately 3/8” off the inner side of the Bottom anti-water strip as shown. Press the Bottom Anti-water strip (07) tightly onto the bottom edge of the Door Glass (01).
©2018 DreamLine. All Rights Reserved 1 2 7/8" Into the hinge Into the hinge 3 4 7/8" 7/8" 8. Take three measurements: from the top edge of the Door Glass (01) to the upper body of the top Hinge (05) (+) 7/8” from the lower body of the upper Hinge to the upper body of the bottom Hinge (+) 1-3/4” from the lower body of the bottom Hinge to top of the installed Bottom anti-water strip (07) (+) 1-7/8” Cut the Side strip (06) according to the measurements.
©2018 DreamLine. All Rights Reserved Fig. 10 If the model includes additional panel glass, refer to the manual that is packaged with the panel glass to continue with the installation.
©2018 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
©2018 DreamLine. All Rights Reserved TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.
©2017 DreamLine. All Rights Reserved UNIDOOR (STYLE G) SHOWER DOOR GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com Style G Right side panel installation shown Please read these instructions carefully before installing.
©2017 DreamLine.
©2017 DreamLine.
©2017 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
©2017 DreamLine.
©2017 DreamLine. All Rights Reserved Detailed Diagram of Glass Panel Components 13 11 9 23 28 The glass surface with the ClearMax™ label must be installed to face inside of the shower 29 8 Packing List 08 09 11 13 L-shaped strip * U-channel 1 (76”, wall profile) Stationary glass Ø5/16” Wall anchor 1pc 23 1pc 28 1pc 29 14pcs Countersunk screw ST4.2x40 Adjustment spacer U-channel 2 (44”, bottom profile) 14pcs 6pcs 1pc NOTE: Unpack your unit carefully and inspect it.
©2017 DreamLine. All Rights Reserved Style “G”: 6”-34” In-Line Half Wall Stationary Panel Installation NOTE: The Unidoor shower door needs to be installed prior to proceeding with the following Stationary Glass installation instructions. Please see the Single Shower Door installation manual included in the door packaging for complete shower door installation instructions. Before you begin the installation, please recheck your shower opening size.
©2017 DreamLine. All Rights Reserved NOTE: Use parts from “Detailed Diagram of Glass Panel Components” for the Stationary Glass assembly and installation. 2. Measure the actual width and height of your Stationary glass (11). See Fig. 2 for details. H Fig. 2 3. NOTE: You will be doing straight cuts for this stationary panel installation. W *It may be necessary to remove any burrs from the cut end of the U-channels with a metal file before placing the U-channel onto the glass.
©2017 DreamLine. All Rights Reserved H (+) 1" b) Fig. 4 4. Slip the cut U-channel 2 (bottom profile) (29) and U-channel 1 (wall profile) (09) onto the Stationary glass (11) in the shown locations. With the door open, place the Stationary glass on the half wall ledge opposite of door. Adjust the Stationary glass and U-channel 1 (wall profile) against the wall to compensate for any out of plumb conditions ensuring that the Stationary glass is level vertically and U-channel 1 is flush with the wall.
©2017 DreamLine. All Rights Reserved 5. While securely holding the Stationary glass (11), close the Glass Door and align the Stationary glass to it. Use the door mark on the ledge as a reference to ensure that the Door is perpendicular to the wall. 2 1 outside Stationary glass Door inside 1/8"-3/16" NOTE: The top of the Stationary glass must be leveled with the Glass door. By traversing across the top of both the Stationary glass and door, height differences can be measured.
©2017 DreamLine. All Rights Reserved 6. Remove the U-Channel 2 (bottom profile) (29) and U-channel 1 (wall profile) (09) from the Stationary glass (11). Carefully set the Stationary glass aside. See Fig. 8 for details. U-channel 1 U-channel 2 Fig. 8 7. Place the c u t U-Channel 2 (bottom profile) (29) onto the ledge in line with the inside mark. Mark the drill holes on the ledge through the predrilled holes in the U-Channel 2 and drill the holes using Ø5/16” drill bit.
©2017 DreamLine. All Rights Reserved Fig. 10 8. Cut the U-channel 1 (wall profile) (09) at the top mark that was made in step #5. Place the U-Channel 1 (wall profile) on the U-Channel 2 (bottom profile) (29) and align vertically with the inside wall mark. Mark the drill holes on the wall through the predrilled holes in the U-Channel 1. 1 U-Channel 1 2 U-Channel 2 3 Now drill holes in the wall using Ø5/16 drill bit and insert the Ø5/16” Wall anchors (13). 4 Ø5/16” 5 See Fig. 11 for details. Fig.
©2017 DreamLine. All Rights Reserved 9. Apply waterproof silicone along the bottom surface and around the holes of the UChannel 1 (wall profile) (09). Fasten the U-Channel 1 to the wall with the Countersunk screw ST4.2x40 (23). Insert the provided Adjustment Spacers (28) into U-Channel 2 (bottom profile) (29) for minor adjustments if necessary. Apply Waterproof silicone into the groove of both U-Channels. NOTE: The surface needs to be clean and free of debris before applying silicone.
©2017 DreamLine. All Rights Reserved 10. Slide the Stationary glass (11) into the groove of both U-Channels. Apply a bead of silicone on the open end of the U-Channel, and its connection. Ensure that the silicone applied to the open end is flat and smooth so that it will not interfere with the installation of the Lshaped strip*(08) in step #12.
©2017 DreamLine. All Rights Reserved 11. Apply a good quality mildew resistant waterproof silicone along the connection of both U-Channels to the wall and ledge on the inside of shower. See Fig. 16 for details. waterproof silicone ATTENTION: Prior to the next step, please be sure the part of the wall and glass edge for installation of the L-shaped strip*(08) is clean, dry and free from soap, oil and any construction debris. 12.
©2017 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
©2017 DreamLine. All Rights Reserved TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.