ENIGMA AIR SHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com Right hand door installation shown For more information about DreamLine® Shower Doors, Tub Doors & Enclosures, please visit DreamLine.
This model is treated with DreamLine’s exclusive ClearMaxTM Glass technology. This is a specially formulated coating that prevents the build up of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. ENIGMA AIR manual Ver 1 Rev 4 06/2017 ©2017 DreamLine. All Rights Reserved For best results, squeegee the glass after each use and dry with a soft cloth.
MODEL #s SHDR-64487610-## SHDR-64606210-## SHDR-64607610-## ##=finish 07- Brushed Stainless steel 08- Polished Stainless Steel Right-Hand door installation ©2017 DreamLine. All Rights Reserved Left-Hand door installation NOTE: This door is reversible for right or left-hand door installation. The right-hand door installation is shown as an example throughout this manual. For the left-hand door installation, simply begin on the opposite wall and reverse the orientation of the steps shown.
NOTE: This manual will describe the single threshold shower door installation only. For the Enigma Air enclosure installation, please refer to the Enigma Air Enclosure manual packaged with the return panel glass. ENIGMA AIR ENCLOSURE SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice.
Reinforcement for Enigma Series Heavy Glass frameless sliding shower door Install studs OR install 2”x 6” wood blocking between the studs where the Guide Rail Brackets will attach to the wall d Stu or X 2” 6” X 2” 6” old k h s c e thr ub de t or d ol k *Blocking height requirement (to center) h s c e thr ub de as measured from threshold or tub deck: t or Enigma Air = 73” for shower ht / 59” for tub ht Enigma X = 72-1/2“ for shower ht / 58-1/2” for tub ht Enigma Z = 73-1/2” for shower ht / 59-1/2“ fo
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Level Phillips Screwdriver Painter’s Tape Tape Measure Drill bit (D=5/16") Pencil Drill bit (D=1/8") Metal File Silicone Power Drill Soft Head Hammer Carpenter’s Square Chop saw and Hacksaw Professional-grade Glass suction cup Top Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered. Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts.
Detailed Diagram of shower door components 7 4 1 8 9 16 6a 5 6b 6 17 2 14 18 3 19 20 15 21 13 12 Parts List Part# Item Qty Part# 10 Item Qty 01 U-channel 1pc 12 Guide Block 1pc 02 Stationary Glass 1pc 13 Anti-water side strip 2pcs 03 Door Glass 1pc 14 Bumper strip 1pc 04 Guide Rail 1pc 15 Handle 1set 05 Stopper 2pcs 16 Ø5/16” (8mm) plastic wall anchor 7pcs 06 Guide Rail Bracket (6a & 6b) 2pcs 17 ST4.2×40 countersunk screw 4pcs 07 Glass Bracket 2pcs 18 ST4.
Installation steps 1. Check both of the finished walls for plumb and the threshold for level. (Fig 1) NOTE: This model does not allow for out-of-plumb adjustment. NOTE: The right-hand door installation is shown as an example throughout this manual. For the left-hand door installation, simply begin on the opposite wall and reverse the orientation of the steps shown. Fig 1 2. Using a Chop-saw or a Hack-saw, cut the Guide Rail (#04) to fit the finished opening.
Finished opening (L) - 1” = finished cut length Guide Rail with the Guide Rail brackets attached L NOTE: Use a metal file to remove any burrs from the cut end of the Guide Rail (#04). Metal File Cut from the door end only which is the end opposite of the holes Fig 3 ©2017 DreamLine. All Rights Reserved 3. This model requires a minimum 2-1/4” of flat threshold space for installation.
4. Align the edge of the U-Channel (#01) to the inside of the mark on the threshold. Mark the position of the U-Channel (#01) on the wall and mark the four holes for drilling through the pre-drilled holes in the U-channel. (Fig 5) U-Channel Fig 5 5. Remove the U-Channel (#01) from the wall and drill the anchor holes using a Ø5/16” drill bit and insert the Wall Anchors (#16). Add a bead of silicone to the back of the U-Channel (#01) and attach it to the wall using four of the ST4.
outside inside 1-1/4” Guide Rail Bracket u-channel h2 h2 Fig 7 1-1/4” 1-1/4” Fig 8 Right hand door installation shown as example h2 h2 6. To position the Guide Rail Brackets (#06): 62” From inside of the shower, measure up from the threshold to the bottom of the Guide Rail Bracket (#06) using Table 1 below. While holding the bracket against the edge of the installed U-channel (#01), mark the wall at the bottom of the bracket.
7. Hold the Guide Rail Bracket (#06) in the marked position and mark the hole for drilling through the Guide Rail Bracket (#06) using a pencil (or center punch). (Fig 9) The guide block bracket should be centered in the bracket as shown to allow for vertical adjustment both up and down. (=) CL (=) Fig 9 8. **Drill a Ø5/16” anchor hole and insert a Wall Anchor (#16). Separate the Guide Rail Bracket (#06) components (6a and 6b). Install the Guide Rail Wall Bracket (#06b) to the wall using one ST4.
9. Insert the Stationary Glass (#02) into the installed U-Channel (#01). ! Use Caution not to bang the glass into the u-channel or threshold. (Fig 11) Fig 11 10. Make sure that your Stationary Glass (#02) is parallel to the front edge of the threshold and mark it. Slide the Guide Block (#12) into the notch of the Stationary Glass (#02), and align flush with the edge of the glass. Mark its position on the threshold and also mark the hole for drilling using a pencil (or center punch).
11. Remove the Stationary Glass (#02) from the U-Channel (#01) and carefully set it aside. (Fig 13) Fig 13 12. To install the Guide Block (#12): Loosen the set screw on the side and remove the guide block face plate. (Fig. 14.
TIP: Bring the door glass into the shower before permanently installing the stationary panel glass and guide rail. 13. Apply silicone into the U-Channel (#01). Slide the Stationary Glass (#02) firmly into the installed U-Channel (#01). ! Use Caution not to bang the glass into the U-channel or threshold. (Fig 15) Fig 15 14. Attach the Stoppers (#05) and Guide Rail Brackets (#06) to both ends of the Guide Rail (#04). (Notice that the top of the guide rail bracket has two set screws).
14. Align the panel end of the Guide Rail (#04) with the installed Guide Rail Wall Bracket (#6b). Slide the Guide Rail Bracket (#6a) over the Guide Rail Wall Bracket (#6b) and tighten the set screws. (Fig 17) 1 2 Fig 17 TIP: Leave the set screws that hold the guide rail to the bracket loose to allow for side to side adjustment of the guide rail to make it easier to align the holes in the guide rail with the holes in the panel glass. Tighten these set screws after the holes are aligned. 15.
16. Level the Guide Rail (#04) across the opening. If necessary, use the set screws on the Guide Rail Bracket (#06) to adjust the level of the Guide Rail (#04). (Fig 19 and Fig 20) Fig 19 17. Using the mark on the door side of the threshold from Step #3, draw a plumb line up the wall on the door side of the opening. Measure over 1-1/4” into the shower from this line. With the Guide Rail (#04) level, mark the position of the Guide Rail Bracket (#06) on the wall.
18. Remove the Guide Rail (#04) from the Stationary Panel Glass (#02). Remove the Guide Rail Bracket (#06) from the Guide Rail (#04) and hold it back in position on the wall and mark the anchor hole. Drill a Ø5/16” hole and insert a Wall Anchor (#16). Separate the Guide Rail Bracket (#06) components (6a and 6b). Attach the Guide Rail Wall Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk Screw (#21).
. Re-check the Guide Rail (#04) for level and if necessary, adjust with the set screws on the Guide ©2017 DreamLine. All Rights Reserved Rail Brackets (#06).
. Measure the distance from the edge of the Guide Block (#12) to the wall. This distance will be (L). Cut the Anti-Splash Threshold (#11) to the size of: (L). (Fig 24) L L Fig 24 22. Apply silicone to the bottom of the Anti-Splash Threshold (#11). Remove the face plate from the 1 2 Right hand door installation shown as example ENIGMA AIR manual Ver 1 Rev 4 06/2017 3 ©2017 DreamLine. All Rights Reserved Guide Block (#12).
23. Temporarily secure the Anti-Splash Threshold (#11) to the threshold with several pieces of painter’s tape to hold it in position tight to the threshold until the silicone fully cures. (Fig 26) Painter’s Tape Fig 26 24. Attach the Rollers (#08) to the Door Glass (#03) with the wheels facing out. NOTE: The roller hardware disk can be rotated to tilt the door glass slightly to create a tight seal with the wall. Make any adjustments after all of the vinyl seals are installed.
25. Align the bottom of the Door Glass (#03) with the Guide Block (#12) and hang the door from the Guide Rail (#04). (Fig 28) 1 2 inside 3 Fig 28 26. Install the Roller Guards (#09) onto the Door Glass (#03) so that 1 the longer section extends beneath the Guide Rail (#04). Use a small allen wrench to hold the shorter part of the roller guard and rotate the larger section so that there is approximately 1/16” of clearance between the Roller Guards (#09) and the Guide Rail (#04).
27. Attach the Handle (#15) to the Door Glass (#03). Attach the Anti-Water Strips (#13) to the edge of the Stationary Panel Glass (#02) and Door Glass (#03). Attach the Bumper Seal Strip (#14) to the handle side of the Door Glass (#03). (Fig 30) 1 Doo r 2 Pan el 3 4 Pan el Doo r Fig 30 28. To position the Stoppers (#05), remove the set screws from the Stoppers (#05) and apply Thread Lock Adhesive (#20) to the threads.
29. Apply good quality mildew-resistant silicone along the connection of the stationary glass with the walls and the threshold. Allow 24 hours for the silicone to fully cure before using the shower. (Fig 32) 24 Hours ©2017 DreamLine.
Product Maintenance BASES and BACKWALLS: To ensure a long life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2017 DreamLine.