ENIGMA AIR SHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com Right hand door installation shown Please read these instructions carefully before installing.
MODEL #s SHDR-64487610-## SHDR-64606210-## SHDR-64607610-## ##=finish 07- Brushed Stainless steel 08- Polished Stainless Steel Left Hand door installation Right Hand door installation NOTE: This door is reversible for right or left-hand door installation. The right-hand door installation is shown as an example throughout this manual. For the left -hand door installation, simply begin on the opposite wall and reverse the orientation of the steps shown.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Tape Measure Level Phillips Screwdriver Drill bit Drill bit (D=5/16") (D=1/8") Pencil Silicone Power Drill Soft Head Hammer Carpenter’s Square Chop-saw or Hack-saw Painter’s Tape Top Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered. Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts. Middle Bottom W NOTE: Unpack your unit carefully and inspect it.
Detailed Diagram of shower door components 7 4 1 8 9 16 6a 5 6b 6 17 2 14 18 3 19 20 15 21 13 12 11 # 1 2 3 4 5 6 7 Item Parts List U-channel Stationary Glass Qty 1pc 1pc Door Glass Guide Rail Stopper 1pc 1pc 2pcs Guide Rail Bracket (6a & 6b) 2pcs Glass Bracket 8 Roller 9 Roller Guard 10 Threshold End Cap 2pcs 2pcs 2pcs 1pc 11 Anti-splash Threshold 1pc ENIGMA AIR manual Ver 1 04/2016 10 # 12 13 14 15 16 17 18 19 20 21 Item Qty Bumper strip 1pc 2pcs 1pc Handle 1set Ø 5/16” (8mm) pla
Installation steps 1. Check both of the finished walls for plumb and the threshold for level. NOTE: This model does not allow for out-of plumb adjustment. See Fig 1 for details Fig 1 2. Using a Chop-saw or a Hack-saw, cut the Guide Rail (#04) to fit the finished opening.
Finished opening “L” - 1” = finished cut length Guide Rail with the Guide Rail brackets attached L NOTE: Use a metal file to remove any burrs from the cut end of the Guide Rail (#04). Cut from the door end only which is the end opposite of the holes Fig 3 3. This model requires a minimum 2-1/4” of flat threshold space for installation. Starting from the wall on the stationary panel side, use a Carpenter’s Square as a guide and measure in 1/4” from the outside of the threshold and mark the threshold.
4. Align the edge of the U-Channel (#01) to the inside of the mark on the threshold. Mark the position of the U-Channel (#01) on the wall and also mark the four holes for drilling. See Fig 5 for details U-Channel Fig 5 5. Remove the U-Channel (#01) from the wall and drill the anchor holes using a Ø5/16” drill bit and insert the Wall Anchors (#16). Add a bead of silicone to the back of the U-Channel (#01) and attach it to the wall using four of the ST4.2 x 40 Countersunk screws (#17).
outside inside 1-1/4 Guide Rail Bracket u-channel h2 h2 Fig 7 1 1/4” 1 1/4” Fig 8 Right hand door installation shown as example h2 h2 6. To position the Guide Rail Brackets (#06): 62” From inside of the shower, measure up from the threshold to the bottom of the Guide Rail Bracket (#06) using Table 1 below. While holding the bracket against the edge of the installed U-channel (#01), mark the wall at the bottom of the bracket.
7. Hold the Guide Rail Bracket (#06) in the marked position and mark the hole for drilling through the Guide Rail Bracket (#06) using a pencil (or center punch.) See Fig 9 for details Fig 9 8. Drill a Ø5/16” anchor hole and insert a Wall Anchor (#16). Separate the Guide Rail Bracket (#06) components (6a and 6b). Install the Guide Rail Wall Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk screw (#21).
9. Insert the Stationary Glass (#02) into the installed U-Channel (#01). Use Caution not to bang the glass into the u-channel or threshold. See Fig 11 for details Fig 11 10. Make sure that your Stationary glass (#02) is parallel to the front edge of the threshold and mark it. Slide the Guide Block (#12) into the notch of the Stationary glass (#02), and align flush with the edge of the glass. Mark its position on the threshold and also mark the hole for drilling using a pencil (or center punch.
11. Remove the Stationary Glass (#02) from the U-Channel (#01) and carefully set it aside. See Fig 13 for details Fig 13 12. To install the Guide Block (#12): Loosen the set screw on the side and remove the guide block face plate (Fig. 14.
TIP: Bring the door glass into the shower before permanently installing the stationary panel glass and guide rail. 13. Apply silicone into the U-Channel (#01). Slide the Stationary Glass (#02) firmly into the installed U-Channel (#01). Use Caution not to bang the glass into the u-channel or threshold. Fig 15 See Fig 15 for details 14. Attach the Stoppers (#05) and Guide Rail Brackets (#06) to both ends of the Guide Rail (#04).
. Align the panel side Guide Rail (#04) with the installed Guide Rail Wall Bracket (#6a). Slide the Guide Rail Bracket (#6b) over the Guide Rail Wall Bracket (#6a) and tighten the set screws. 1 See Fig 17 for details 2 Fig 17 15. Attach the Stationary Glass (#02) to the Guide Rail (#04) using the Glass Brackets (#07).
16. Level the Guide Rail (#04) across the opening. If necessary, use the set screws on the Guide Rail Bracket (#06) to adjust the level of the Guide Rail (#04). See Fig 19 & 20 for details Fig 19 17. Using the mark on the door side of the threshold from Step #3, draw a plumb line up the wall on the door side of the opening. Measure over 1-1/4” into the shower from this line. With the Guide Rail (#04) level, mark the position of the Guide Rail Bracket (#06) on the wall.
18. Remove the Guide Rail (#04) from the Stationary Panel 1 Glass (#02). Remove the Guide Rail Bracket (#06) from the Guide Rail (#04) and hold it back in position on the wall and mark the anchor hole. Drill a Ø5/16” anchor hole and insert a Wall Anchor (#16). Separate the Guide Rail Bracket (#06) components (6a and 6b). Attach the Guide Rail Wall Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk screw (#21). Ø5/16” 2 3 See Fig 21 for details 4 6b 6a Fig 21 19.
20. Recheck theGuide Rail (#04) for level and if necessary, adjust with the set screws on the Guide Rail Brackets (#06).
21. Measure the distance from the edge of the Guide Block (#12) to the wall. This distance will be “L”. Cut the Anti-splash threshold (#11) to the size of: L”. See Fig 24 for details L L Fig 24 22. Apply silicone to the bottom of the Anti-Splash Threshold (#11.) Remove the face plate from the Guide block (#12) , Insert one end of the Anti-splash threshold (#11) fully into the Guide block (#12) and replace the guide block face plate.
23. Temporarily secure the Anti-Splash Threshold (#11) to the threshold with several pieces of painter’s tape to hold it in position tight to the threshold until the silicone fully cures. See Fig 26 for details Painter’s Tape Fig 26 24. Attach the Rollers (#08) to the Door Glass (#03) with the wheels facing out. NOTE: The roller hardware disk can be rotated to tilt the door glass slightly to create a tight seal with the wall. Make any adjustments after all of the vinyl seals are installed.
25. Align the bottom of the Door Glass (#03) with the Guide Block (#12) and hang the door from the Guide Rail (#04). 1 See Fig 28 for details 2 inside 3 Fig 28 26. Install the Roller Guards (#09) onto the Door Glass (#03) so that 1 the longer section extends beneath the Guide Rail (#04). Use a small allen wrench to hold the shorter part of the roller guard and rotate the larger section so that there is approximately 1/16” of clearance between the Roller Guards (#09) and the Guide Rail (#04).
27. Attach the Handle (#15) to the Door Glass (#03). Attach the Anti-water strips (#13) to the edge of the Stationary panel glass (#02) and Door glass (#03). Attach the Bumper seal strip (#14) to the handle side of the door glass. See Fig 30 for details 2 1 4 3 Fig 30 28. Position the Stoppers (#05): Remove the set screws from the Stoppers (#05) and apply Thread Lock Adhesive (#20) to the threads. Re-insert the set screws into the Stoppers (#09) and screw them tightly to the Guide Rail (#04).
29. Apply good quality mildew-resistant silicone along the connection of the stationary glass with the walls and the threshold. Allow 24 hours for the silicone to fully cure before using the shower.
Product Maintenance BASES and BACKWALLS: To ensure a long life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosure please visit DreamLine.
