Installation&Assembly

ManualsBrandsDreffco ManualsCooling & Air QualityGreat Northwest Vented Natural Gas/Propane Fireplace Logs

INSTALLATION

AND OPERATION

INSTRUCTIONS

DECORATIVE GAS LOG SETS

Your Decorative Gas Log Set is designed for installation

in an existing approved, fully vented, wood-burning fire-

place which includes gas hook-up. The burner may be

fueled by either natural or propane gas. A propane

changeover kit and a safety pilot are required when the

unit will be used with propane. The safety pilot assembly

may also be required by local codes for use in natural

gas applications.

SHIPPING AND PACKING LIST

Hearth Kit package contains:

1– Burner/pan assembly (with internal orifice)

1– Grate

1– Bag-Sand

1– Bag-ember material

1– Bag-black cinders

2– Grate steps

ATTACHED TO PAN

Log set package contains:

1– Front log

1– Back log

3 to 6—Stacking accent logs of varying sizes

1– Gas Connector

1-1/2” to 3/8” adaptor

1– Damper Clamp

GENERAL INFORMATION

These instructions are intended as a general guide and

do not supersede national or local codes in any way.

Authorities having jurisdiction should be consulted be-

fore installation.

Decorative Gas Log Sets

INSTALLATION

1. Open the damper and install the damper clamp over

the lip of the damper. Tighten the screw until the

clamp is secure.

Refer to figure 1.

FIGURE 1

Page 1

WARNING

FOR YOUR SAFETY– Do not store or use gasoline

or other flammable vapors or liquids in the vicinity

of this or any other appliance.

WARNING

Use the manual shut-off valve to shut off the gas

supply to the fireplace before continuing with

installation procedures.

IMPORTANT

Read these instructions carefully before installing

or operating the decorative gas log set. These in-

structions should be left with the homeowner for fu-

ture reference.

Summary of content (6 pages)

PAGE 1
INSTALLATION AND OPERATION INSTRUCTIONS DECORATIVE GAS LOG SETS Your Decorative Gas Log Set is designed for installation in an existing approved, fully vented, wood-burning fireplace which includes gas hook-up. The burner may be fueled by either natural or propane gas. A propane changeover kit and a safety pilot are required when the unit will be used with propane. The safety pilot assembly may also be required by local codes for use in natural gas applications.
PAGE 2
FIGURE 2 2- The burner / pan assembly is shipped ready for right-hand gas connection. NOTE- If an 18” log set is being installed with a safety pilot kit, if left-hand gas supply connection is necessary, or if unit must be converted for use with propane gas, follow the steps outlined in the sections which begin on page 3 and then continue with step 3. 3– Remove the existing cap or gas jet assembly from the gas stub in your fireplace. Clean the threads using either a wire brush or steel wool.
PAGE 3
WARNING The sand/ember mixture can be stacked up to the bottom of the grate in natural gas applications; however, this is not the case in propane applications. The Vermiculite/ember combination should not be stacked more than 1/2” above the height of the burner pan in propane applications. Again, the sand provided with the hearth kit is NOT to be used in propane applications. The Vermiculite provided with the gas changeover kit must be used instead. 11– Arrange the top logs on top of the base logs.
PAGE 4
3- If unit is not equipped with safety pilot, replace brass elbow in burner pipe on the left side of the burner pan, and brass hex plug in burner pipe on the right side of burner pan. Use pipe dope or Teflon tape for this operation. Continue installation (step 3 - page 2). 4- If unit is not equipped with safety pilot, pilot must also be disassembled and reassembled for left side installation. Refer to figure 5 for parts identification. PILOT ASSEMBLY Conversion (Fig.
PAGE 5
OPERATION WARNING All gas-burning appliances produce smoke and carbon monoxide gas during operation. These fumes can be harmful if not properly vented. The damper must be open and the chimney must be drawing properly to ensure safe operation of this decorative gas log set. Lighting Log Sets Without the Safety Pilot Assembly 1– Place the fireplace damper in the fully open position. The damper must be in the fully open position any time the log set is in operation.
PAGE 6
Page 6 24" 27" 30" 36" 42" 48" FRONT WIDTH IN INCHES 16 16 16 16 16 16 16 16 16 16 16 16 24" 27" 30" 36" 42" 48" FRONT WIDTH IN INCHES 18" 21" 24" 30" 36" 42" LOG SET SIZE 24" 27" 30" 36" 42" 48" FRONT WIDTH IN INCHES 7"W.C. 7"W.C. 7"W.C. 7"W.C. 7"W.C. 7"W.C. 16 16 16 16 16 16 39 44 48 58 62 68 7"W.C. 7"W.C. 7"W.C. 7"W.C. 7"W.C. 7"W.C. 16 16 16 16 16 16 16 16 16 16 16 16 39 44 48 58 62 68 11"W.C. 11"W.C. 11"W.C. 11"W.C. 11"W.C. 11"W.C.