User manual

ManualsBrandsDuerkopp Adler ManualsBusiness equipmentHP Series Additional guide

dc15xx

CONTROL dc1500 AB220A5111

FP220A5911

dc1550 AB320A5211

FP320A5951

KL2334a

LIST OF PARAMETERS

CONNECTION DIAGRAM

TIMING DIAGRAMS

No. 402301 English

FRANKL & KIRCHNER EFKA OF AMERICA INC. EFKA ELECTRONIC MOTORS

GMBH & CO KG SINGAPORE PTE. LTD.

Summary of content (88 pages)

PAGE 1
dc15xx CONTROL dc1500 dc1550 AB220A5111 FP220A5911 AB320A5211 FP320A5951 0 I P E + - >> KL2334a LIST OF PARAMETERS CONNECTION DIAGRAM TIMING DIAGRAMS No. 402301 FRANKL & KIRCHNER GMBH & CO KG English EFKA OF AMERICA INC. EFKA ELECTRONIC MOTORS SINGAPORE PTE. LTD.
PAGE 2
PAGE 3
EFKA AB220A/320A FP220A/320A 3 CONTENTS Page 1 Use of the C200 Compiler (FP220A..../FP320A....) 5 2 Table of Adapter Cords 6 3 Putting into Service 7 4 Setting and Putting into Service with the Aid of the Fast Installation Routine (SIR) 8 5 Operating Elements and Socket Connectors 9 5.1 5.2 5.3 5.
PAGE 4
PAGE 5
EFKA AB220A/320A FP220A/320A 1 Use of the C200 Compiler (FP220A..../FP320A....) The C200 Compiler can only be used with the FP220A and FP320A controls! The Efka C200 Compiler is a software tool for the programming of functions on the FP220A and/or FP320A controls, with which the user can program a variety of additional user-defined functions. The compiler provides the following basic functions: § § § § § predetermined functions which are integrated by means of a system file approx.
PAGE 6
EFKA AB220A/320A FP220A/320A 2 Table of Adapter Cords ATTENTION! Before switching functional sequences, detach cables from the inputs and outputs! Please ensure that the machine installed provides the functional sequence to be set! Then proceed with the setting using parameter 290! Setting the functional sequence using parameter 290 Mode Designation Adapter Power transistors è 0 FL VR M1 M2 M3 M4 M5 M6 ST2/35 ST2/34 ST2/37 ST2/28 ST2/27 ST2/36 ST2/32 ST2/30 FL FL FL FL FL FL FL FL VR VR VR VR VR VR
PAGE 7
EFKA AB220A/320A FP220A/320A Explanation of letter symbols of the previous page and chapter ”Timing Diagrams“ Outputs: FL VR FA FA2 FA-V FAU FSPL FW ML/NK RB KB MST PD≥1 PD=0 L-STL FZ IMP LFA = Sewing foot lifting = Backtacking = Thread trimmer = Thread trimmer pos. 1A...2 = Thread trimmer forward = Bobbin thread trimmer = Thread tension release = Thread wiper = Machine running / Needle cooling = Chain blowing in opposite direction = Chain blowing = Machine at standstill = Pedal steps 1...
PAGE 8
EFKA AB220A/320A FP220A/320A 4 Setting and Putting into Service with the Aid of the Fast Installation Routine (SIR) The Fast Installation Routine (SIR) passes through all parameters necessary for programming the functional sequence and the positions.
PAGE 9
EFKA AB220A/320A FP220A/320A 5 Operating Elements and Socket Connectors 5.1 Position of Operating Elements and Displays S1 S2 S3 S4 S5 LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Display 5.
PAGE 10
5.
PAGE 11
EFKA AB220A/320A FP220A/320A 11 Inputs switched to +24V ATTENTION! When connecting the outputs, ensure that a total power of 96VA constant load will not be exceeded! 1) 2) 3) 4) *) Nominal voltage 24V, no-load voltage max. 30V momentarily after power on Transistor output with open collector max.
PAGE 12
EFKA AB220A/320A FP220A/320A Connection of a HSM001 Hall sensor module or an IPG001 pulse encoder Connection of a LSM002 light barrier module Adapter cord 1113229 in case of multiple assignment of socket B18! POS2 OUT POS IN G1/G2 OUT TXD/RXD LSM IN LSM002 HSM... IPG... - Output for position 2 Input for positions Output of generator impulses Serial transmission lines Possibility of connecting a light barrier module to socket B18/8 (If parameter 239 = 0, the light barrier function is selected.
PAGE 13
EFKA AB220A/320A FP220A/320A EB.. Pedal step è Input A Input B Input C Input D 5.
PAGE 14
EFKA AB220A/320A FP220A/320A 6 Connection Scheme of SM210A Stepping Motor Control mot V810/V820 DC1500/1550 variocontrol 820 P E variocontrol 810 2 3 4 5 6 7 8 9 10 11 P 12 E + 1 2 3 4 5 6 1 2 3 4 M 1 1 4 SM 01 1 B41 B5 M B41 M B5 mot 1 B80 B2 B776 M B2 B776 EB... V8 . . B18 B19 control LSM... B18 B18 B776 LSM... V8 . . B18 B19 B80 B776 Nr.1113172 ST2 ST1 ST2 ST1 0 SM210.... I AB220A..../FP220A.... AB320A..../FP320A....
PAGE 15
EFKA AB220A/320A FP220A/320A 7 Adapter Cords Adapter cord for AISIN models AD3XX, AD158, 3310 and EK1 Setting the functional sequence Setting the functions of the keys è è è Thread trimming mode Input in1 Input in3 Nr.
PAGE 16
EFKA AB220A/320A FP220A/320A Adapter cord for BROTHER model FD3 B257 Setting the functional sequence Setting the functions of the keys è è è è è Thread trimming mode Input in1 Input in3 Input in4 Input in5 Set parameter 290 Set parameter 240 Set parameter 242 Set parameter 243 Set parameter 244 = 5 = 7 = 18 = 16 = 17 Nr.
PAGE 17
EFKA AB220A/320A FP220A/320A Adapter cord for BROTHER model B-891 Setting the functional sequence Setting the functions of the keys (Automatic setting) 2 +5V 3 R-N-EXT 4 0V 5 in5 6 in3 8 19 in4 20 SUB- D- 37 1 Nr.
PAGE 18
EFKA AB220A/320A FP220A/320A Adapter cord for DÜRKOPP ADLER models 210, 270 Setting the functional sequence Setting the functions of the keys è è è è è Thread trimming mode Input in1 Input in3 Input in4 Input in5 Set parameter 290 Set parameter 240 Set parameter 242 Set parameter 243 Set parameter 244 = 0 = 16 = 1 = 3 = 17 Nr.
PAGE 19
EFKA AB220A/320A FP220A/320A Adapter cord for JUKI model 5550-6 Setting the functional sequence Setting the functions of the keys è è Thread trimming mode Input in2 Set parameter 290 Set parameter 241 = 14 = 16 Nr.
PAGE 20
EFKA AB220A/320A FP220A/320A Adapter cord for JUKI model LU1510-7 Setting the functional sequence Setting the functions of the keys (Automatic setting) Thread trimming mode Input in1 Input in3 Input in4 Input in6 Input in7 è è è è è è Set parameter 290 Set parameter 240 Set parameter 242 Set parameter 243 Set parameter 245 Set parameter 246 = = = = = = Nr.
PAGE 21
EFKA AB220A/320A FP220A/320A Adapter cord for JUKI model DNU1541-7 Setting the functional sequence Setting the functions of the keys (Automatic setting) Thread trimming mode Input in1 Input in2 Input in3 Input in4 Input in5 Input in6 Input in7 è è è è è è è è Set parameter 290 Set parameter 240 Set parameter 241 Set parameter 242 Set parameter 243 Set parameter 244 Set parameter 245 Set parameter 246 = = = = = = = = Nr.
PAGE 22
EFKA AB220A/320A FP220A/320A Adapter cord for JUKI model LU2210, LU2260 Setting the functional sequence Setting the functions of the keys (Automatic setting) SUB- D- 37 20 19 37 ZVR 1 3 R-N-EXT 0V 2 4 0V NHT 3 5 in5 VRU 4 6 in3 HP 5 7 in1 HP 6 8 in4 HP 7 11 in2 FL 8 13 in9 VR 9 14 i10 +24V 10 15 +15V +24V 11 16 +24V +24V 12 17 +24V 18 +24V 19 Set parameter 290 Set parameter 240 Set parameter 241 Set parameter 242 Set parameter 243 Set parameter 244 S
PAGE 23
EFKA AB220A/320A FP220A/320A Adapter cord for KANSAI model RX9803 Setting the functional sequence Setting the functions of the keys è è Thread trimming mode Input in1 ST2 2 SUB- D- 37 +5V +5V 1 LSP 2 0V 3 4 0V 7 in1 +24V 1 16 +24V FA 2 17 +24V +24V 3 18 +24V FW 4 20 +24V 5 ML 6 26 +24V 27 M3 32 M5 1 35 FL 2 37 M1 1 2 3 6 3 5 2 4 1 37 19 +24V 3 FL 4 1 2 3 4 *) = 5 = 7 Nr.
PAGE 24
EFKA AB220A/320A FP220A/320A Adapter cord for PFAFF model 1425, 1525 Thread trimming mode Input in1 Input in2 Input in3 Input in4 Input in5 Input in7 Input in8 Input in9 Input i10 Nr.
PAGE 25
EFKA AB220A/320A FP220A/320A Adapter cord for PEGASUS models W500/UT, W600/UT/MS with or without stitch condensing Setting the functional sequence Setting the functions of the keys è è Thread trimming mode Input in1 Set parameter 290 Set parameter 240 = 5 = 7 Nr.
PAGE 26
EFKA AB220A/320A FP220A/320A Adapter cord for PEGASUS model MHG Setting the functional sequence Setting the functions of the keys Set parameter 290 Set parameter 240 Set parameter 241 Set parameter 242 Set parameter 243 +5V in4 1 0V 2 1 ST2 20 SUB- D- 37 1 19 = = = = = Nr.
PAGE 27
EFKA AB220A/320A FP220A/320A Adapter cord for RIMOLDI model F27 Setting the functional sequence = 5 1 SUB- D- 37 20 16 +24V 17 +24V FW 1 18 +24V ML 2 FAO 3 27 M3 FAU 4 28 M2 FL 5 +24V 37 19 Set parameter 290 Nr.
PAGE 28
EFKA AB220A/320A FP220A/320A Adapter cord for UNION SPECIAL models CS100 and FS100 Setting the functional sequence Setting the functions of the keys è è è Thread trimming mode Input in1 Input in3 Set parameter 290 Set parameter 240 Set parameter 242 = 4 = 6 = 6 Nr.
PAGE 29
EFKA AB220A/320A FP220A/320A Adapter cord for UNION SPECIAL model 34700 with stitch lock Setting the functional sequence Setting the functions of the keys è è è Thread trimming mode Input in8 Input in9 Nr.
PAGE 30
EFKA AB220A/320A FP220A/320A Adapter cord for UNION SPECIAL models 34000 and 36200 Setting the functional sequence Setting the functions of the keys è è è è è Thread trimming mode Input in1 Input in3 Input in4 Input in5 Nr.
PAGE 31
EFKA AB220A/320A FP220A/320A Adapter cord for YAMATO chainstitch machines VC/VG series Setting the functional sequence Setting the functions of the keys è è Thread trimming mode Input in1 Set parameter 290 Set parameter 240 = 5/21 = 7 Nr.
PAGE 32
EFKA AB220A/320A FP220A/320A Adapter cord for YAMATO backlatch machine model ABT3 Setting the functional sequence Setting the functions of the keys (Automatic setting) è è è Thread trimming mode Input in1 Input in3 Set parameter 290 Set parameter 240 Set parameter 242 = 9 = 6 = 10 Nr.
PAGE 33
EFKA AB220A/320A FP220A/320A 8 Timing Diagrams Mode 0 (lockstitch) 1 1/2 0 -1 -2 + n3 n n2 n1 n2 0 1 2 3 1 2 3 POS.1 n4 0 1 2 n7 1 2 3 ST2/20 POS.
PAGE 34
EFKA AB220A/320A FP220A/320A Mode 2 (lockstitch) - 1 1/ 2 0 -1 + -2 n6 n n3 n2 n1 n4 0 1 2 3 POS.1 0 1 2 n7 n7 n1 n1 3 ST2/20 SSc POS.
PAGE 35
EFKA AB220A/320A FP220A/320A Mode 3 and/or 26 (lockstitch) - 1 1/ 2 0 -1 + -2 n n3 n2 0 1 2 3 1 2 3 POS.1 n10 n2 1 2 3 4 5 6 7 n4 n7 0 1 2 1 2 n7 3 ST2/20 tFA POS.
PAGE 36
EFKA AB220A/320A FP220A/320A Mode 4 (chainstitch) - 1 1/ 2 0 + -1 -2 n n3 n2 0 1 2 3 4 5 6 7 POS.1 ST2/20 n1 n4 n7 012 3 4 5 POS.
PAGE 37
EFKA AB220A/320A FP220A/320A Mode 5 (chainstitch) - 1 1/ 2 0 -1 + -2 n6 n 0 1 POS.1 n3 n2 n1 n4 23 n7 0 1 2 3 1 2 ST2/20 SSc POS.
PAGE 38
EFKA AB220A/320A FP220A/320A Mode 5 (chainstitch) Union Special, bag sewing machine - 1 1/ 2 0 -1 + -2 n6 n 0 1 POS.1 n2 n1 2 ST2/20 SSc POS.2 ST2/21 t3 FL ST2/35 t4 t5 kdF STV ST2/34 M2 (IMP) ST2/28 kt2 kd3 M3 (BR) ST2/27 kt3 M5 (ML) ST2/32 M6 (MST) ST2/30 in1...i10 ST2/.. 0256/ MODE- 5a Mark FAm SSt SAk in1...
PAGE 39
EFKA AB220A/320A FP220A/320A Mode 4, 5, 6 or 7 (function “unlocking the chain” with light barrier) 1 - 1/ 2 0 + -1 -2 n n2 POS.1 n5 n1 n1 0 3 4 5 6 7 ST2/20 POS.2 drd ird ST2/21 t3 FL ST2/35 LS t4 t5 STV ST2/34 M5 (ML) ST2/32 M6 (MST) ST2/30 LS ENTK 0256/ ENTK- 1 Mark FAm drE Frd LS mEk in7 in8 in..
PAGE 40
EFKA AB220A/320A FP220A/320A Mode 4, 5, 6 or 7 (function “unlocking the chain”) + 1 1/ 2 0 -1 -2 n n2 n1 n2 n1 n1 n1 POS.1 ST2/20 POS.2 drd Ird drd Ird ST2/21 t3 FL ST2/35 STV ST2/34 M5 (ML) ST2/32 M6 (MST) ST2/30 ENTK 0256/ ENTK- 2 Mark FAm drE Frd in7 in8 in..
PAGE 41
EFKA AB220A/320A FP220A/320A Mode 6 (chainstitch with fast scissors) parameter 232 = 1 - 1 1/ 2 0 -1 + -2 n6 n 0 1 POS.1 n3 n2 n6 n7 23 0 1 n3 n2 n7 23 ST2/20 SSc POS.
PAGE 42
EFKA AB220A/320A FP220A/320A Mode 7 (overlock) parameter 232 = 0 (tape cutter) / parameter 018 = 0 (seam end with stop) - 1 1/ 2 0 + -1 -2 n n3 n2 n1 n2 012345678 POS.1 n5 n4 n7 1 3 4 5 1 2 3 4 5 6 7 ST2/20 POS.
PAGE 43
EFKA AB220A/320A FP220A/320A Mode 7 (overlock) parameter 232 = 1 (fast scissors) / parameter 018 = 0 (seam end with stop) - 1 1/ 2 0 -1 + -2 n n3 n2 n1 n2 012345678 POS.1 n5 n4 n7 1 3 4 5 1 2 3 4 5 6 7 ST2/20 POS.
PAGE 44
EFKA AB220A/320A FP220A/320A Mode 7 (overlock) parameter 232 = 0 (tape cutter) / parameter 018 = 1 (seam end without stop) - 1 1/ 2 0 -1 + -2 n n3 n2 0123456 POS.1 ST2/20 n4 n3 1234567 n2 n1 n7 0123456 POS.
PAGE 45
EFKA AB220A/320A FP220A/320A Mode 8 (backlatch Pegasus) - 1 1/ 2 0 -1 + -2 n6 n 0 1 POS.1 n2 n12 n1 n6 2 0 1 n2 n1 2 ST2/20 SSc POS.
PAGE 46
EFKA AB220A/320A FP220A/320A Mode 9 (backlatch Yamato) - 1 1/ 2 0 -1 + -2 n6 n POS.1 ST2/20 0 1 POS.
PAGE 47
EFKA AB220A/320A FP220A/320A Mode 10 (lockstitch) - 1 1/ 2 0 + -1 -2 n n3 n2 0 1 2 3 4 5 6 7 POS.1 ST2/20 n1 n4 n7 012 3 4 5 POS.
PAGE 48
EFKA AB220A/320A FP220A/320A Mode 13 (lockstitch / Pfaff 1425, 1525) - 1 1/ 2 0 + -1 -2 n n3 n11 n2 0 1 2 3 1 2 3 POS.1 ST2/20 n4 n7 0 1 2 1 2 VR ST2/34 t3 n7 3 tFA POS.
PAGE 49
EFKA AB220A/320A FP220A/320A Mode 14 (lockstitch) - 1 1/ 2 0 -1 + -2 n n3 n2 n1 n2 0 1 2 3 1 2 3 POS.1 n4 0 1 2 n7 1 2 3 ST2/20 POS.
PAGE 50
EFKA AB220A/320A FP220A/320A Mode 15 (Pegasus SSC100) sequence when high lift for walking foot is Off / start of seam with light barrier covered - 1 1/ 2 0 + -1 -2 n n2 POS.1 n1 1 3 4 5 6 7 ST2/20 POS.
PAGE 51
EFKA AB220A/320A FP220A/320A Mode 15 (Pegasus SSC100) sequence when high lift for walking foot is Off / start of seam with light barrier uncovered 1 - 1/ 2 0 + -1 -2 n n2 n1 n2 n1 POS.1 1 3 4 5 6 7 ST2/20 POS.
PAGE 52
EFKA AB220A/320A FP220A/320A Mode 15 (Pegasus SSC100) sequence when high lift for walking foot is On - 1 1/ 2 0 + -1 -2 n n2 POS.1 n1 1 3 4 5 6 7 ST2/20 POS.
PAGE 53
EFKA AB220A/320A FP220A/320A Mode 16 (feed-off-the-arm machine) without automatically unlocking the chain with tape cutter (232 = 0) - 1 1/ 2 0 -1 + -2 n n3 n2 n1 n2 012345678 POS.1 n5 n4 1 3 4 5 1 2 3 4 5 6 n7 7 ST2/20 POS.
PAGE 54
EFKA AB220A/320A FP220A/320A Mode 16 (feed-off-the-arm machine) automatically unlocking the chain with tape cutting / 8 key on V820 On - 1 1/ 2 0 + -1 -2 n n2 n1 n2 n5 n4 n7 1 3 4 5 1 2 3 4 5 1 POS.1 2 3 ST2/20 drd ird POS.
PAGE 55
EFKA AB220A/320A FP220A/320A Mode 17 (stitch lock Pegasus) - 1 1/ 2 0 -1 + -2 n n2 n7 n7 n2 n1 n7 POS.1 ST2/20 dr POS.
PAGE 56
EFKA AB220A/320A FP220A/320A Mode 20 (lockstitch Juki LU1510-7 / DNU1541-7) - 1 1/ 2 0 -1 + -2 n n3 n2 n11 n9 n10 n2 0 1 2 3 1 2 3 POS.1 n4 n7 0 1 2 1 2 3 ST2/20 dr POS.
PAGE 57
EFKA AB220A/320A FP220A/320A Mode 21 (stitch lock) - 1 1/ 2 0 -1 + -2 n3 n n2 n1 n4 0 1 2 3 POS.1 n7 n7 0 1 2 3 ST2/20 tFA POS.
PAGE 58
EFKA AB220A/320A FP220A/320A Mode 22 (lockstitch Brother B-891) - 1 1/ 2 0 -1 + -2 n n3 n2 n11 n2 0 1 2 3 1 2 3 POS.1 n4 n7 0 1 2 1 2 n7 3 ST2/20 tFA POS.
PAGE 59
EFKA AB220A/320A FP220A/320A Mode 23 (lockstitch) - 1 1/ 2 0 -1 + -2 n n3 n2 0 1 2 3 1 2 3 POS.1 n10 n2 1 2 3 4 5 6 7 n4 n7 n7 0 1 2 1 2 3 ST2/20 tFA POS.
PAGE 60
EFKA AB220A/320A FP220A/320A Mode 24 (Pegasus MHG-100) “bottom hemming“ On Power on 1 1/ 2 0 + -1 -2 n n2 n1 n2 n1 n2 0 POS.1 ST2/20 n5 n7 3 4 5 6 POS.
PAGE 61
EFKA AB220A/320A FP220A/320A Mode 24 (Pegasus MHG-100) “sleeve hemming“ On Power on 1 1/ 2 0 + -1 -2 n n2 n1 n2 n1 n2 0 POS.1 ST2/20 n5 n7 3 4 5 6 POS.
PAGE 62
EFKA AB220A/320A FP220A/320A Mode 25 (lockstitch Juki LU2210/LU2260) - 1 1/ 2 0 -1 + -2 n n3 n2 0 1 2 3 1 2 3 POS.1 n10 n2 1 2 3 4 5 6 7 n4 n7 0 1 2 1 2 n7 3 ST2/20 tFA POS.
PAGE 63
EFKA AB220A/320A FP220A/320A 9 List of Parameters 9.1 Preset Values Depending on Mode The preset values which are different in the various modes are listed in the table below. When switching the mode by means of parameter 290, these values change automatically.
PAGE 64
EFKA AB220A/320A FP220A/320A Supplier Level Mode è Parameter 200 201 202 203 204 ** 205 206 207 208 209 210 211 212 213 220 234 240 241 242 243 244 245 246 247 248 249 250 ** 251 ** 252 ** 253 255 260 262 269 270 271 272 ** 274 ** 275 ** 280 ** 281 ** 282 ** 283 ** 284 ** 285 ** 286 ** 287 ** 288 291 292 293 294 296 297 0 2 3 4 5 6 7 8 9 10 x x x x x x x - x 0 x x x x x - 13 7 1 22 16 19 33 31 28 17 x x x x x x x - 160 350 100 12 6 3 25 100 0 200 x x - 5 3 - - 100 - 200 0 0 0 0 0 5 8 3
PAGE 65
EFKA AB220A/320A FP220A/320A 9.2 Operator Level The preset values of the following list of parameters refer to the setting of parameter 290 = 0.
PAGE 66
EFKA AB220A/320A FP220A/320A Operator Level Parameter Designation Unit 019 -Pd 0 = Pedal in pos. –1 disabled in the seam. With pedal in pos. –2 in the seam, only sewing foot lifting is possible. (Function only if parameter 009 = 1) 1 = Pedal in pos. –1, sewing foot lifting disabled in the seam. 2 = Pedal in pos. –2, thread trimming disabled. (Function only if parameter 009 = 1) 3 = Pedal in pos. –1 and –2 enabled in the seam. 4 = Pedal in pos. –1 and –2 blocked in the seam.
PAGE 67
EFKA AB220A/320A FP220A/320A 9.3 Technician Level Code no. 190 with control operation Code no.
PAGE 68
EFKA AB220A/320A FP220A/320A Technician Level Code no. 190 with control operation Code no. 1907 with control panel operation Parameter 132 LSS 0 = 133 LSE 134 135 136 SSt SrS FAr 137 139 141 hP nIS SGn 142 SFn 143 kSA 144 kSE *) Designation Unit Machine start possible with light barrier uncovered or covered. 1= Machine start blocked with light barrier uncovered if parameter 131 = 1. Machine start blocked with light barrier covered if parameter 131 = 0.
PAGE 69
EFKA AB220A/320A FP220A/320A Technician Level Code no. 190 with control operation Code no.
PAGE 70
EFKA AB220A/320A FP220A/320A Technician Level Code no. 190 with control operation Code no.
PAGE 71
EFKA AB220A/320A FP220A/320A Technician Level Code no. 190 with control operation Code no.
PAGE 72
EFKA AB220A/320A FP220A/320A Technician Level Code no. 190 with control operation Code no. 1907 with control panel operation Parameter Designation Unit 195 LSc Stitches for light barrier monitoring stitches (light barrier monitoring is off, when set to “0”).
PAGE 73
EFKA AB220A/320A FP220A/320A 9.4 Supplier Level Code no. 311 with control operation Code no. 3112 with control panel operation Parameter Designation Unit 200 t1 Delay until speed release after start backtack ms 201 t2 Sewing foot lift switch-on delay with half ms heelback 202 t3 Start delay after disabling the sewing foot ms lift signal 203 t4 Time of full power of sewing foot lifting ms 204 t5 Holding power for sewing foot lifting % 1...
PAGE 74
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no. 3112 with control panel operation Parameter Designation Unit 234 PdO New start after machine run blockage 0= New start after disabling machine run blockage without influence by the pedal (e. g. with automats) 1= New start after disabling machine run blockage only if pedal in pos.
PAGE 75
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no. 3112 with control panel operation Parameter Designation Unit Handwheel running in the opposite direction of rotation according to the setting of parameter 161 22 = Speed limitation n11 (flip-flop 2). Output ST2/29 is enabled according to setting of parameter 186 23 = No function 24 = Needle to position 2 (see instruction manual) 25 = Speed limitation with ext.
PAGE 76
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no.
PAGE 77
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no. 3112 with control panel operation Parameter Designation Unit 263 ihP 0 = Signal “high lift for walking foot” (M6), when key is closed. 1 = Signal “high lift for walking foot” (M6), when key is open. (Function only if parameter 137 = 1) 264 iS1 0 = Signal “manual stacker” (M7), when key is closed. 1 = Signal “manual stacker” (M7), when key is open.
PAGE 78
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no. 3112 with control panel operation Parameter Designation Unit 270 PGm Connection of a sensor e. g. light barrier sensor to light barrier socket B18/7. Selection of the desired function! 0 = Function as in table on previous page! 1 = Setting the sensor to position 2. Set position 1 using parameter 271, starting from trailing edge position 2. 2 = Setting the sensor to position 2.
PAGE 79
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no.
PAGE 80
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no. 3112 with control panel operation Parameter Designation Unit Lockstitch mode: Juki (LU1510-7 /DNU1541-7) »Slide-in strip for V810 and V820 = 1« 21 = Chainstitch mode with stitch lock: Yamato (VG2730-156M) »Slide-in strip for V810 = 5« »Slide-in strip for V820 = 3« 22 = Lockstitch mode: Brother (B-891) »Slide-in strip for V810 and V820 = 1« 23 = Lockstitch mode: Dürkopp Adler (271...
PAGE 81
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no. 3112 with control panel operation Parameter Designation Unit 296 M08 Functions of signal M8 0 = Signal M8 Off 1 = Signal hemmer foot On at the start of the seam with pedal in pos. -1 or –2 and in the seam with machine running 2 = Signal hemmer foot On at the start of the seam with pedal in pos.
PAGE 82
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no.
PAGE 83
EFKA AB220A/320A FP220A/320A Parameter A1 301 302 303 304 305 308 309 A2 311 312 313 314 315 318 319 [ms] [ms] [St] [St] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 100 0 0 1 0 1 100 100 0 0 3 0 0 0 0 0 10 3 0 2 0 0 10 10 3 0 1 100 0 0 10 1 0 2 0 100 10 0 2 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 1 100 0 0 0 0 0 2 0 0 10 0 1 3 0 0 100 0 0 1 3 1 100 100 0 0 3 3 0 0 0 0 10 3 3 2 0 0 10 10 3 3
PAGE 84
EFKA AB220A/320A FP220A/320A Parameter A1 301 302 303 304 305 308 309 A2 311 312 313 314 315 318 319 [ms] [ms] [St] [St] 0 1 0 0 0 0 0 0 1 1 100 0 0 0 0 1 2 0 0 10 0 1 1 0 0 100 0 0 1 1 1 100 100 0 0 3 1 0 0 0 0 10 3 1 2 0 0 10 10 3 1 1 100 0 0 10 1 1 2 0 100 10 0 1 2 0 0 100 0 0 1 2 1 100 100 0 0 NA LS NE FA-E P=0 100 10 100 100 100 10 10 10 100 10 10 100 100 100 100 0256/ BILD4 See previous page f
PAGE 85
EFKA AB220A/320A FP220A/320A Supplier Level Code no. 311 with control operation Code no.
PAGE 86
EFKA AB220A/320A FP220A/320A 10 Error Displays General Information On the control On the V810 On the V820 Signification A1 InF A1 InF A1 Pedal not in neutral position, when turning the machine on A2 -StoP- blinking -StoP- blinking + symbol display Machine run blockage A3 InF A3 InF A3 Reference position is not set A6 InF A6 InF A6 Light barrier monitoring A7 Symbol blinking Symbol blinking Bobbin thread monitor Programming Functions and Values (Parameters) On the control On the
PAGE 87
EFKA AB220A/320A FP220A/320A 11 Slide-in Strips for the V810/V820 Control Panels Slide-in strips for the V810 control panel Slide-in strips for the V820 control panel 1 R F R F R F 3 R F 4 2 F1 R 1 2 F2 F1 F2 F1 F2 5 F 6 INSERT F1 DELETE F2 7 F1 1 1 1 2 2 2 F F F F2 8 INSERT F1 DELETE F2 INSERT F1 DELETE F2 9 10 INSERT F1 DELETE F2 KL2256e Note When changing the setting of parameters 291 / 292, the V810 / V820 functions change as well, save function keys
PAGE 88
FRANKL & KIRCHNER GMBH & CO KG SCHEFFELSTRASSE 73 – D-68723 SCHWETZINGEN TEL.: +49-6202-2020 – TELEFAX: +49-6202-202115 email: info@efka.net – http://www.efka.net OF AMERICA INC. 3715 NORTHCREST ROAD – SUITE 10 – ATLANTA – GEORGIA 30340 PHONE: (770) 457-7006 – TELEFAX: (770) 458-3899 – email: efkaus@efka.net ELECTRONIC MOTORS SINGAPORE PTE. LTD. 67, AYER RAJAH CRESCENT 05-03 – SINGAPORE 139950 PHONE: +65-67772459 – TELEFAX: +65-67771048 – email: efkaems@efka.