Specifications

ManualsBrandsDux ManualsHome building and Decor26XL

Installation by a licensed tradesperson and in

accordance with:

• AS/NZS 3500.4 “National Plumbing &

Drainage Code Hot Water Supply Systems

– Acceptable Solutions”

• AS5601/AG601 Gas Installation

• Adherence to local authority and OH&S

regulations

• Victorian PIC Requirements

Installer’s Guide

For advice, repairs and service, call:

1300 365 115 (Australia)

0800 729 389 (New Zealand)



Read This Document First

On completion, sign and leave with owner

Gas continuous ow water heater

Models: 26XL

26XN

Part No: IG090701

Version: B

Specications and materials may change without notice

Effective for Endurance continuous ow water heaters manufactured and sold after 1st Sept 2009.

Summary of content (14 pages)

PAGE 1
Installer’s Guide Important INFORMATION Read This Document First On completion, sign and leave with owner Gas continuous flow water heater Models: 26XL 26XN Installation by a licensed tradesperson and in accordance with: • AS/NZS 3500.
PAGE 2
Installer’s Guide – Endurance six™ Installation Guide Step 1 • Arrive at site, park vehicle as close as allowable to installation, and conduct a safety audit. • Safety audits can also be known as Work Method Statements (WMS) or Job Site Analysis (JSA). Note – do not commence a job where the risks can’t be controlled. Step 2 • The existing water heater (if applicable) should be drained and removed in a responsible manner. Note: Do not drain on to grass or garden beds.
PAGE 3
Installer’s Guide – Endurance six™ Installation Guide • Refer to the Owner’s Manual and AG 601 for detailed installation instructions. • Plan hot water pipework to ensure optimum flow rates to all outlets. Step 4 • Check labels located on the unit’s side for: a. maximum inlet water pressure; a Pressure Limiting Valve may be required. b. gas supply pressure requirements (minimums = 1.13kPa for Natural Gas, 2.75kPa for LPG) c.
PAGE 4
Installer’s Guide – Endurance six™ Installation Guide Step 5 Water Connection • Using correct plumbing methods, connect the cold water pipe to the heater. Note: According to local regulations and the plumbing code, fit any and all valves that are necessary e.g. tempering valves, pressure limiting valves, duo valves, cold water expansion valves etc. We recommend the use of new valves for all Installation. Please refer plumbing code and/or local requirements.
PAGE 5
Installer’s Guide – Endurance six™ Installation Guide Step 7 Gas Connection • Fit a union to the water heater gas inlet for easy connection and removal. The thread diameter is R¾/20. • Fit an AGA approved isolating gas cock in the supply line adjacent to the water heater gas connection. Gas Valve • Ensure that the supply pipe and the gas pressure regulator (LPG or Natural Gas) has sufficient flow capacity for this and other appliances connected to the fitting line. Refer to AG 601 for size of pipe.
PAGE 6
Installer’s Guide – Endurance six™ Step 8 • This unit has a preset temperature of 50°C. • If controllers are installed, the maximum temperature setting will still be 50°C. Step 9 • Make sure there is water inside the unit prior to turning on the power. This can be achieved by turning on the tap. Step 10 • If the water heater has been installed correctly, when the power is turned on the heater will go through initialisation. This will take a few seconds.
PAGE 7
Installer’s Guide – Endurance six™ Installation Guide Step 11 Installation Of Main Remote Control • Detach the fitting bracket from Main remote controller by sliding it down. Bad examples • Attach the fitting plate to wall. • Install conduit inside of wall in advance and secure the wiring box. • Pass remote controller cables through conduit. Chemicals Do NotRemote Control Main Model CMR-2252 • Then pass the cables through the hole of the fitting bracket and pull them out.
PAGE 8
Installer’s Guide – Endurance six™ Installation Guide Step 12 Installation of Shower Remote Control • Drill a hole (more than diameter about 12mm) in a wall for the remote controller cables. • After passing the remote controller cables through the hole, remove the packing’s back paper of remote controller. Then attach the remote controller to the wall. • Detach both end covers of remote controller and fix the remote controller to the wall with wood screws (2 pcs) in the screw holes provided.
PAGE 9
Installer’s Guide – Endurance six™ Installation Declaration Location of Installation: ........................................................................................... ............................................................................................................................... ............................................................................................................................... Tank Serial Number: .........................................................
PAGE 10
Installer’s Guide – Endurance six™ 10 Part No: IG090701 Version: B
PAGE 11
Installer’s Guide – Endurance six™ Part No: IG090701 Version: B 11
PAGE 12
Installer’s Guide – Endurance six™ Gas continuous flow water heater Models: 26XL 26XN For advice, repairs and service, call: 1300 365 115 (Australia) 0800 729 389 (New Zealand) Part No: IG090701 Version: B
PAGE 13
INSTRUCTIONS FOR UNITS SUPPLIED SET AT 50℃ TO COMPLY WITH AS 3498-2009. PLEASE NOTE THIS 50℃ UNIT IS NOT TO BE USED IN CONJUNCTION WITH SOLAR WATER HEATERS. 1) This water heater is to be installed to comply with AS/NZS 3500.4 and AS5601 codes and any local by laws or regulations. 2) Please refer to the Installation / Operating instructions supplied with this water heater for details of the installation procedure.
PAGE 14
MR PLUMBER. PLEASE NOTE this Dux Endurance unit is supplied factory set at 50℃ outlet hot water temperature to comply with the requirements of AS 3498-2009. This Endurance hot water unit does not require a tempering valve to be installed. Installation instructions. Please follow all the installation instructions in the Dux Endurance Installation and operating instructions handbook and the following additional instructions for the Hot water outlet connection. 1.