Installation Sheet

ManualsBrandsDXV ManualsPlumbingDXV Modulus Wall Mounted Elongated Chair Height Toilet Bowl Only - Seat Included

- 1 -

INSTALLATION INSTRUCTIONS

SAVE FOR FUTURE USE

Product names listed herein are trademarks of AS America, Inc.

7302314-100 Rev. B (6/17)

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing

supply stores. It is essential that the tools and materials be on hand before work is begun.

Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before you begin.

(Certain installations may require professional help.) Also be sure your installation conforms to local codes.

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly deﬁne contour of china and components.

DXV Modulus

™

Wall Hung Dual Flush

Toilet with Seat

Model D23040A Series

Regular Screwdriver

10'

Level

Closet Bolts

Putty Knife

Tape Measure

Hacksaw

SealantAdjustable Wrench

Flexible Supply Tube

ROUGHING-IN DIMENSIONS: for GEBERIT FRAME

ALL INSTALLATION PROCEDURES MUST COMPLY IN STRICT ACCORDANCE WITH APPLICABLE LOCAL

PLUMBING AND BUILDING CODES.

SUPPLY

AS REQUIRED

19-3/4"

(500 mm)

22"

(559 mm)

14-3/16"

(361 mm)

5-1/2"

(140 mm)

11-13/16"

(350 mm)

FINISHED RIM

HEIGHT (FRM)

FRM = X

PLUS 76

3" (76 mm)

(100 mm)

3-1/2"

(90 mm)

26-3/8"

(670 mm)

6-3/8"

(162 mm)

5-1/2"

MIN.

(140 mm)

2-13/16"

(72 mm)

1/2"

NPT

4" MIN.

(100 mm)

FINISHED

FLOOR

FINISHED

FLOOR

STUD FRONT

CENTER PIPE

4-1/4"

(108 mm)

18-1/2"

(470 mm)

13-3/4"

(350 mm)

7-1/8"

(180 mm)

0" - 7-7/8"

(0 - 200 mm)

12"-16"

(305-407 mm)

45"-49"

(1143-1249 mm)

OPTIONAL SUPPLY

FOR WASHLET SEAT

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS DXV Modulus™ Wall Hung Dual Flush Toilet with Seat Model D23040A Series Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE! NOTE: Pictures may not exactly define contour of china and components.
PAGE 2
1b ROUGHING-IN DIMENSIONS: for GROHE FRAME 19-11/16" (500 mm) 5-1/2" MIN. (140 mm) 1/2" NPT SUPPLY AS REQ’D 14-3/16" (361 mm) 5-1/2" (140 mm) 18-1/2" (470 mm) 44-1/2"-48-7/16" (1130-1230 mm) 7-1/16" (180 mm) 22" (559 mm) 11-13/16" (300 mm) X 13-3/4" (350 mm) 12"-16" (305-407 mm) FINISHED FLOOR 4" (100 mm) FINISHED RIM HEIGHT (FRM) FRM = X PLUS 76 3" (76 mm) FINISHED FLOOR 0" - 7-7/8" (0 - 200 mm) 4" MIN.
PAGE 3
6 6a BOWL INSTALLATION: Remove yellow protection plugs and seals from pipes. 6b Insert discharge pipe into the pipe hub in the wall. Place a straight edge flush against the wall and mark a line on the pipe. Fit finned rubber seal onto flush pipe. Repeat same procedure for discharge pipe. 6c Place discharge pipe with gasket into waste outlet of bowl. Also place flush pipe with fin gasket into inlet of bowl. Then mark a second line on both pipes. Add dimension X and 1/8" (3 mm).
PAGE 4
6f 6g Install both seals into the pipes in the wall. Lubricate seals with appropriate rubber seal lubricant. Remove protective sleeves from threaded mounting rods. Install rods with a protruding length of 1-3/8" (35 mm) from the finished wall. Then install the threaded nuts leaving approximately 3/8" (10 mm) of the threaded rod exposed. Also insure the concave portion of the nut is facing down! Install both pipes into the hubs in the wall.