Installation Sheet

ManualsBrandsDXV ManualsBathroom FaucetsOak Hill 1.2 GPM Wall Mounted Bridge Bathroom Faucet

- 1 -

INSTALLATION INSTRUCTIONS

SAVE FOR FUTURE USE

In the United States:

DXV by American Standard

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV by American Standard

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV by American Standard

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials which are available from hardware and plumbing

supply stores. It is essential that the tools and materials be on hand before work is begun.

ROUGHING-IN DIMENSIONS:

• For reference

Product names listed herein are trademarks of AS America, Inc.

M965648

Thank you for selecting DXV by American Standard.

To ensure that your installation proceeds smoothly,

please read these instructions carefully

before you begin.

Oak Hill

™

Wall-Mount Lavatory Faucet

Model D35155450

Adjustable Wrench Channel Locks Sealing Tape Level

8 mm

Hex wrench

(203 mm)

2-3/16" DIA.

(58 mm)

14-1/8"

(359 mm)

(102 mm)

4-3/16"

(106 mm)

6-15/16"

(176 mm)

6-1/2"

(165.2 mm)

15˚

3-1/16"

(78 mm)

SINK INSTALLATION

WALL INSTALLATION

4-3/16"

(106 mm)

6-15/16"

(176 mm)

15˚

CROSS BRACE

FINISHED WALL

HOLE SIZE IN WALL

1-5/16" MIN. (33 mm)

1-1/4

" MAX. (45 mm)

13/16" MIN. (19.5 mm)

" MAX. (32.2 mm)

1/2" ELBOW WITH

MOUNTING FLANGE

WALL STUDS

6-1/2"

(165.2 mm)

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Oak Hill™ Wall-Mount Lavatory Faucet Model D35155450 Most of the procedures require the use of common tools and materials which are available from hardware and plumbing supply stores. It is essential that the tools and materials be on hand before work is begun. Adjustable Wrench Channel Locks Sealing Tape ROUGHING-IN DIMENSIONS: • For reference Level 8 mm Hex wrench SINK INSTALLATION 8" (203 mm) 6-15/16" (176 mm) 4" (102 mm) 4-3/16" (106 mm) F O R 2-3/16" DIA.
PAGE 2
DXV SINK INSTALLATION 1 INSTALL MOUNTING WASHERS • Install METAL WASHER (1) and RUBBER WASHER (2) onto each SUPPLY SHANK (3). 3 1 2 3 1 2 2 INSTALL SUPPLY SHANKS TO LAVATORY • From behind the sink, insert SUPPLY SHANKS (3) with washers into the faucet holes. • Install ESCUTCHEON (4) and ADAPTER NUT (5) onto each SUPPLY SHANK (3). Hand tighten. These parts must be installed loosely and should be able to move around within the two sink holes. Keep Inlet Holes on SUPPLY SHANKS (3) facing down.
PAGE 3
DXV SINK INSTALLATION 4 REALIGN MOUNTING PARTS • Make sure both inlet holes on SUPPLY SHANKS (3) are still facing downward. • Check that the faucet is level and make sure both MOUNTING NUTS (6) are fully threaded against the ESCUTCHEONS (4). Align faucet body with the DXV logo on sink. — To fully tighten MOUNTING NUTS (6): turn faucet nut clockwise while holding SUPPLY SHANKS (3) nut. 4 6 3 DXV Logo INLET HOLES DOWN 5 INSTALL SUPPLY HOSES 3 • Thread SUPPLY HOSES (7) into SUPPLY SHANK (3) inlet holes.
PAGE 4
WALL-MOUNT INSTALLATION 1 WALL MOUNT INSTALLATION • Determine where the finished wall location will be. This measurement is very important! Note: The rough-in measurement from the end of the elbow to the finished wall is a minimum of 13/16" (19mm) and a maximum of 1-1/4" (32.2mm). • Determine the height of the faucet from the finished floor and mark the center line of each ELBOW (9) exactly 8" apart on the wood support. Attach the two ELBOWS (9) to the wood support with wood screws on each center line.
PAGE 5
WALL-MOUNT INSTALLATION 3 ALIGN OFFSET SHANKS • Turn off water supplies. Remove the two PIPE PLUGS. Apply SEALING TAPE to the end of each OFFSET SHANK (10) and thread into each ELBOW (9) with a 8mm HEX WRENCH. • Check that the OFFSET SHANKS (10) are level and centers are 8" (203mm) apart. Distance needs to be maintained accurately. • Adjust each OFFSET SHANK (10) if needed with the 8mm HEX WRENCH until OFFSET SHANKS (10) are level.
PAGE 6
WALL-MOUNT INSTALLATION 4 INSTALL ESCUTCHEONS AND ADAPTER NUTS • Install ESCUTCHEON (4) and ADAPTER NUT (5) onto each OFFSET SHANK (10). Gradually tighten ADAPTER NUTS (5) until ESCUTCHEONS (4) are flush against the finished wall. 4 10 4 4 5 5 5 5 INSTALL FAUCET • Insert faucet inlets into ADAPTER NUTS (5) and OFFSET SHANKS (10). • Gradually tighten MOUNTING NUTS (6) evenlty.
PAGE 7
Oak Hill™ Wall-Mount Lavatory Faucet MODEL NUMBER D35155450 Replace the “YYY” with appropriate finish code M964987-YYY0A MOUNTING KIT POLISHED CHROME 100 BRUSHED NICKEL 144 PLATINUM NICKEL 150 SATIN BRASS 427 M964986-0070A SET SCREW AND SEAL KIT H960136.191 1/2" CARTRIDGE (CLOCKWISE ON) H960104.