User manual

Page 3
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
www.elektroautomatik.de
[e-mail]
PSI 9000 DT Series
TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty ......................................................... 5
1.3 Limitation of liability ........................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................7
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical Data ...............................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ................................... 9
1.8.3 Specictechnicaldata .................................10
1.8.4 Views ............................................................22
1.9 Construction and function ............................ 26
1.9.1 General description ...................................... 26
1.9.2 Block diagram ..............................................26
1.9.3 Scope of delivery .........................................27
1.9.4 Optional accessories ...................................27
1.9.5 The control panel (HMI) ...............................28
1.9.6 USB port (rear side) .....................................31
1.9.7 Ethernet port ................................................31
1.9.8 Analog interface ...........................................31
1.9.9 Sense connector (remote sensing) .............31
2
INSTALLATION & COMMISSIONING
2.1 Storage ......................................................... 32
2.1.1 Packaging ....................................................32
2.1.2 Storage ......................................................... 32
2.2 Unpacking and visual check ........................ 32
2.3 Installation ....................................................32
2.3.1 Safety procedures before installation and
use ................................................................32
2.3.2 Preparation ................................................... 32
2.3.3 Installing the device .....................................32
2.3.4 Connection to AC supply .............................37
2.3.5 Connection to DC loads ...............................37
2.3.6 Grounding of the DC output ........................38
2.3.7 Connection of remote sensing ....................38
2.3.8 Connecting the analog interface .................38
2.3.9 Connecting the USB port (rear side) ...........39
2.3.10 Initial commission .........................................39
2.3.11 Commissionafterarmwareupdateora
long period of non-use .................................39
3
OPERATION AND APPLICATION
3.1 Personal safety ............................................40
3.2 Operating modes .........................................40
3.2.1 Voltage regulation / Constant voltage .........40
3.2.2 Current regulation / constant current / current
limiting ..........................................................41
3.2.3 Power regulation / constant power / power
limiting ..........................................................41
3.2.4 Internal resistance regulation ......................41
3.3 Alarm conditions ..........................................42
3.3.1 Power Fail ...................................................42
3.3.2 Overtemperature .......................................... 42
3.3.3 Overvoltage protection.................................42
3.3.4 Overcurrent protection .................................42
3.3.5 Overpower protection ..................................42
3.4 Manual operation .........................................43
3.4.1 Switching on the device ...............................43
3.4.2 Switching off the device ...............................43
3.4.3 CongurationviaMENU ..............................43
3.4.4 Adjustment limits (Limits) ............................. 50
3.4.5 Changing the operating mode ..................... 50
3.4.6 Manual adjustment of set values .................51
3.4.7 Switching the main screen view ..................52
3.4.8 The meter bars ............................................. 52
3.4.9 Switching the DC output on or off ................53
3.5 Remote control ............................................. 54
3.5.1 General .........................................................54
3.5.2 Control locations ..........................................54
3.5.3 Remote control via a digital interface ..........54
3.5.4 Remote control via the analog interface
(AI) ................................................................55
3.6 Alarms and monitoring ................................. 59
3.6.1 Denitionofterms ........................................59
3.6.2 Device alarm and event handling ................ 59
3.7 Control panel (HMI) lock ..............................61
3.8 Loadingandsavingauserprole ...............62
3.9 The function generator.................................63
3.9.1 Introduction...................................................63
3.9.2 General .........................................................63
3.9.3 Method of operation ..................................... 64
3.9.4 Manual operation .........................................64
3.9.5 Sine wave function ....................................... 65
3.9.6 Triangular function .......................................65
3.9.7 Rectangular function .................................... 66
3.9.8 Trapezoidal function .....................................67
3.9.9 DIN 40839 function ......................................67
3.9.10 Arbitrary function ..........................................68
3.9.11 Ramp Function .............................................72
3.9.12 Remote control of the function generator....72
3.10 Other applications ........................................73
3.10.1 Series connection ........................................73
3.10.2 Parallel operation .........................................73
3.10.3 Operation as battery charger .......................73