Labornetzgeräteserie PS 8000 2U 640W - 3000W 32V - 720V 4A - 120A PS 8032-20 2U: PS 8065-10 2U: PS 8160-05 2U: PS 8080-40 2U: PS 8080-60 2U: 09 230 130 09 230 131 09 230 132 09 230 133 09 230 134 PS 8080-120 2U: PS 8160-60 2U: PS 8360-15 2U: PS 8360-30 2U: PS 8720-15 2U: 09 230 135 09 230 136 09 230 137 09 230 138 09 230 139
DE Allgemeines Impressum Bedienungsanleitung Labornetzgerät Serie PS 8000 2U Elektro-Automatik GmbH & Co. KG Helmholtzstrasse 31-33 41747 Viersen Germany Telefon: +(49) 02162 / 37850 Fax: +(49) 02162 / 16230 Web: www.elektroautomatik.de Mail: ea1974@elektroautomatik.
DE Inhaltsverzeichnis 1. Einleitung 5 2. Technische Daten 2.1 Bedien- und Anzeigeeinheit 2.2 Gerätespezifische Daten 5 5 6 3. Gerätebeschreibung 3.1 Ansichten 3.2 Lieferumfang 7 7 8 4. Allgemeines zum Gerät 4.1 Vorwort / Warnhinweis 4.2 Kühlung 4.3 Gerät öffnen 8 8 8 8 5. Installation 5.1 Sichtprüfung 5.2 Netzanschluss 5.3 Anschluss DC-Ausgang 5.4 Anschlußklemme Fernfühlung 5.5 Slot für Erweiterungskarte 8 8 8 8 8 8 6. Bedienung 6.1 Die Anzeige- und Bedieneinheit 6.2 Tasten am Bedienfeld 6.
DE Über das Gerät 1. Einleitung Die Labornetzgeräte der Serie PS 8000 2U sind durch ihr 19“Einschubgehäuse besonders für Prüfsysteme und Industriesteuerungen geeignet. Über die gängigen Funktionen von Netzgeräten hinaus können 5 verschiedene Sollwertvorgabesätze eingestellt, gespeichert und bei Bedarf abgerufen werden. Weiterhin ist eine fest integrierte, analoge Schnittstelle, die die gängigen Spannungsbereiche 0...5V und 0...10V bedient, vorhanden.
* Bezogen auf den Nennwert Artikelnummer Schutzklasse Überspannungskategorie EMV-Normen Sicherheit Gewicht Abmessungen (BxHxT) Luftfeuchtigkeit rel. Lagertemperatur Umgebungsstemperatur Übertemperaturabschaltung Kühlung Einstellauflösung Verschiedenes Genauigkeit* Einstellbereich Nennleistung bei < 150V UE Ausgang - Leistung Nennleistung PNenn Ausregelzeit 10….
© 2009, Elektro-Automatik GmbH & Co.
DE Über das Gerät 3.2 Lieferumfang Bei Lastzuleitungen bis 1,5m empfehlen wir: 1 x Netzgerät bis 10A: 0,75mm² bis 15A: 1,5mm² 1 x Gedruckte Bedienungsanleitung bis 30A: 4mm² bis 40A: 6mm² 1 x Netzkabel bis 60A: 16mm² bis 120A: 35mm² 1 x Stecker für System Bus pro Anschlußleitung (Litze, frei verlegt) mindestens zu verwenden. 4. Allgemeines zum Gerät 4.
DE Über das Gerät Bild 3 Erläuterungen: 1- Anzeige links: Spannungsistwert oder Sollwert U, UVL, OVP 2- Statusfeld: Statusanzeigen wie CC, CV usw. 3- Anzeige rechts: Stromistwert oder Sollwert I, P 4- Steuerungstasten: Bedienung des Gerätezustandes u.a. 5- Drehgeber rechts: Sollwerteinstellung I, P, sowie im Setup Einstellwerte 6- Preset-Tasten: Umschalten auf Sollwertanzeige 7- Drehgeber links: Sollwerteinstellung U, UVL, OVP, sowie im Setup Parameter wählen 6.
DE Bedienung des Gerätes In der Sollwertsatzauswahl (Memory Select) wird mit der Taste auch auf die zum Sollwertsatz gehörige Unterspannungs- bzw. Überspannungschwelle umgeschaltet, aber die hier eingestellten Werte werden nicht sofort übernommen. Die Anzeige sieht dann so aus: bzw. . Taste Preset Power Im Normalbetrieb dient die Taste zum Umschalten der Stromistwertanzeige auf den Leistungssollwert (Preset-Modus).
DE Bedienung des Gerätes c) Nur speichern 6.3 Ausgang aus, einen oder mehrere Sollwertsätze anwählen, Sollwerte einstellen, dann Druck >3s auf die Taste --> alle Sollwertsätze werden gespeichert, aber keiner übernommen. Der Ausgang bleibt aus, nach dem Speichern wird der MemoryModus beendet. Tasten Drehgeber Die Sollwertsätze können auch über die digitale Schnittstelle mittels entsprechender Befehle vorgegeben werden und werden dabei dabei gespeichert.
DE Bedienung des Gerätes 2. Fernsteuerbetrieb über analoge Schnittstelle Über die analoge Schnittstelle (kurz: AS) können Strom, Spannung und Leistung gestellt werden. Dies geschieht immer gleichzeitig. Das heißt, man kann nicht Spannung über die AS vorgeben und Strom und Leistung am Gerät mit dem Drehgeber einstellen oder umgekehrt. Bei Geräten unter 1kW Ausgangsleistung ist der Leistungssollwert PSEL (siehe „Analoge Schnittstelle“) nicht wirksam und muß nicht vorgegeben werden.
DE Bedienung des Gerätes 7.5 Übertemperatur Überhöhte Umgebungstemperatur >40°C ist unbedingt zu vermeiden! Sobald ein Übertemperaturfehler (OT) durch interne Überhitzung auftritt, wird der Ausgang abgeschaltet und der Status „OT“ erscheint im Statusfeld. Gleichzeitig blinkt die LED „Output On“ um anzuzeigen, daß sich der Ausgang nach dem Abkühlen automatisch wieder einschaltet.
DE Bedienung des Gerätes 8. Geräte-Setup Folgender Parameter für RS232-Schnittstelle IF-R1: Das Geräte-Setup dient zur Konfiguration einiger Parameter, die nicht ständig benötigt werden. Drei Grundparameter sind immer verfügbar. Weitere Parameter werden nur angezeigt, wenn sich eine Schnittstellenkarte im Slot befindet. Das Geräte-Setup kann nur bei Ausgang „aus“ durch gleichzeitiges Drücken der beiden Drehgeber-Tasten (siehe Abschnitt 6.3) >2s erreicht werden.
DE Bedienung des Gerätes • Der Eingang Rem-SB (Remote Standby, Pin 13) überlagert die Taste Output On. Das heißt, das Gerät kann dann nicht mit der Taste eingeschaltet werden, wenn der Pin das Signal „aus“ vorgibt (Not-Aus-Funktion). 10.2 Anwendungen Übersicht Sub-D-Buchse • Der Ausgang VREF kann genutzt werden, um Sollwerte für die Sollwerteingänge VSEL, CSEL und PSEL zu bilden.
DE Bedienung des Gerätes Ausgang aus (Not-Aus) Der Pin „REM-SB“ ist immer wirksam, also selbst als steuernder Pin nicht von REMOTE abhängig und kann daher ohne weitere Maßnahmen zum Ausschalten des Ausganges genutzt werden, auch für eine Not-Aus-Funktion. Hierbei muß der Anwender nur sicherstellen, daß der Schaltzustand des Pins gehalten wird. 11. Sonstiges 11.
Bedienung des Gerätes 11.2 Funktionen der Klemme System Bus Die auf der Rückseite befindliche, 8polige Klemme System Bus dient zum Anschluß von Fernfühlungsleitungen, sowie zum Verbinden von Steuerleitungen zwischen gleichartigen Geräten zwecks Reihen- oder Parallelschaltung.
DE Bedienung des Gerätes 11.2.2 Parallelschaltung im Share-Bus-Betrieb Hinweis: diese Betriebsart eignet sich am besten für Spannungsregelbetrieb. Achtung! Es dürfen nur Geräte gleichen Typs zusammen geschaltet werden. Um den Ausgangsstrom zu erhöhen, können zwei oder mehrere Geräte zusammengeschaltet werden. Auf ausreichendem Querschnitt der Lastleitung ist zu achten. Vorzugsweise sollten bei der Parallelschaltung symmetrische Leitungslängen und Querschnitte angeschlossen werden.
Bedienung des Gerätes DE 11.3 Networking Die Grafiken unten zeigen Beispiele für die digitale Fernsteuerung von mehreren Netzgeräten gleichzeitig in sternförmiger (USB, RS232) oder busförmiger (CAN, GPIB) Vernetzung. Es gelten jeweils die für die Schnittstellen und Bussysteme vorhandenen Vorgaben und Beschränkungen. Über USB können von einem PC aus bis zu 30 Geräte angesteuert werden, entsprechende Hubs mit eigener Stromversorgung vorausgesetzt. Die gilt prinzipiell auch für RS232.
DE © 2006, Elektro-Automatik GmbH & Co. KG Irrtümer und Änderungen vorbehalten 20 © 2009, Elektro-Automatik GmbH & Co.
Laboratory Power Supply Series PS 8000 2U 640W - 3000W 32V - 720V 4A - 120A PS 8032-20 2U: PS 8065-10 2U: PS 8160-05 2U: PS 8080-40 2U: PS 8080-60 2U: 09 230 130 09 230 131 09 230 132 09 230 133 09 230 134 PS 8080-120 2U: PS 8160-60 2U: PS 8360-15 2U: PS 8360-30 2U: PS 8720-15 2U: 09 230 135 09 230 136 09 230 137 09 230 138 09 230 139
EN General About User instruction manual for power supply series PS 8000 2U Elektro-Automatik GmbH & Co. KG Helmholtzstrasse 31-33 41747 Viersen Germany Phone: +(49) 02162 / 37850 Fax: +(49) 02162 / 16230 Web: www.elektroautomatik.de Mail: ea1974@elektroautomatik.
EN Table of contents 1. Introduction 25 2. Technical specifications 2.1 Control panel and display 2.2 Technical specifications 25 25 26 3. Device description 3.2 Scope of delivery 27 28 4. General 4.1 Prologue / Warning 4.2 Cooling 4.3 Opening the device 28 28 28 28 5. Installation 5.1 Visual check 5.2 Mains connection 5.3 DC output terminal 5.4 Terminal „Sense“ (Remote sense) 5.5 Interface card slot 28 28 28 28 28 28 6. Handling 28 6.1 The display 28 6.2 Pushbuttons on the control panel 29 6.
EN About the device 1. Introduction The laboratory power supplies of the series PS 8000 2U are ideally suited for test systems and industrial control facilities by their 19“ draw-out case. Apart from standard functions of power supplies the user can define and recall 5 different presets of set values or make use of the integrated analogue interface, that can handle the common voltage ranges of 0...5V or 0...10V. This offers a way of easily monitoring the device as well as total remote control.
* Related to the nominal value Cooling Overtemperature shutoff Ambient temperature Storage temperature Humidity rel. Dimensions (WxHxD) Weight Safety EMC standards Overvoltage class Protection class Article number Accuracy* Adjustable range Resolution of adjustment Miscellaneous Ripple Accuracy* Resolution of display Transient recovery time 10….
© 2009, Elektro-Automatik GmbH & Co.
EN About the device 3.2 Scope of delivery The outputs “+” and “-“ are not grounded, so that one of them may be grounded if necessary. 1 x Power supply unit Attention! When grounding one of the output poles always check if one of the poles of the load (eg. electronic load) is also grounded.
EN About the device Figure 3. Control panel Legend: 1- Left display area: Actual voltage or set value U, UVL, OVP 2- Status area: status display like CC, CV etc. 3- Right display area: Actual current or set value I, P 4- Control buttons: Setting the device condition etc.
EN Operating the device In memory selection mode the button is also used to switch to the UVL or OVP value of the selected memory set, but in this mode the values are not valid yet. The left display area will then show like this: resp. . During remote control by analogue or digital interface the preset mode can be used to check the current set value that is given from remote. The button may be locked by the condition LOCK. See below.
EN Operating the device The memory sets can also be defined by remote control and corresponding commands using a digital interface (except GPIB). They‘re stored immediately. 6.3 Further control elements Pushbuttons Rotary encoder The button may be locked by the condition LOCK. See below. Pushbutton Local Both of the rotary encoders have a push button function. Pushing any or both of these will effect following: a) Fine adjustment mode (Fine) This pushbutton activates or deactivate the LOCAL mode.
EN Operating the device 2. Remote control by analogue interface The analogue interface (short: AI) allows to remotely control current, voltage and power (models from 1kW), always in combination. It means, that it‘s not possible to adjust voltage by the AI and the current with the rotary encoder on the front at the same time, or vice versa. Because the OVP threshold can not be adjusted via the AI, it‘s required to set it manually on the device before using the remote control.
EN Operating the device Simultaneously, the LED „Output On“ will flash, indicating that the output will automatically switch on again as soon as the device has cooled down. In case this is not wanted, the output can be manually switched off. Then the LED stops flashing and the output won‘t switch automatically on. OT errors have to be acknowledged.
EN Operating the device 8. Device setup Following settings only with RS232 interface IF-R1: The device setup is intended to set parameters that are not constantly altered. Three elementary settings are always available, other settings only if a digital interface card is equipped. The device setup can be accessed while the output is switched off and by pressing both pushbuttons of the rotary encoders (see section 6.3) simultaneously >2s.
EN Operating the device • The input REM-SB (remote standby, pin 13) overrides the pushbutton Output On. It means, the output can not be switched on by the button if the pin defines the output state as „off“ So it can be as emergency power off. 10.2 Example applications Overview D-Sub socket • The output VREF can be used to build set values for the set value inputs VSEL, CSEL and PSEL. For example, if only current control is required, pin VSEL and PSEL can be bridged to VREF.
EN Operating the device Output off (emergency off) Pin „REM-SB“ is always operative and does not depend on the remote mode. It can thus be used to switch off the output without extra means, for example as an emergency power off function. All the user has to do is to ensure the level of the input is held. 11. Miscellaneous 11.
EN Operating the device It is recommended to define one unit as master that controls voltage and current of the system. At any slave the set values of voltage, current and power (if available) should be set to 100%. All units displays their actual values, there will be no totals formation of the system output current. In order to control the whole system remotely, it is sufficient to control the master via its analogue or digital interface.
EN Operating the device Figure 6. Parallel connection with Share Bus Figure 7. USB or RS232 networking © 2006, Elektro-Automatik GmbH & Co. KG Irrtümer und Änderungen vorbehalten Figure 8. CAN networking example, also applies to GPIB 38 © 2009, Elektro-Automatik GmbH & Co.
EA-Elektro-Automatik GmbH & Co. KG Entwicklung - Produktion - Vertrieb Helmholtzstraße 31-33 41747 Viersen Telefon: 02162 / 37 85-0 Telefax: 02162 / 16 230 ea1974@elektroautomatik.de www.elektroautomatik.