Replacement Part List

6
No. Description Part No
1. Air Cap Ring L0151
2. Air Cap L0152
3. Air Distributor Plate L0162
4. Fluid Tip, 0.08” L0157
5. Fluid Tip Seal L0159
6. Pivot Screw L0179
7. Washer L0195
8. Main Body L0180
9. Fluid Needle 0.08” L0166
10. Adaptor L0174
11. Spring L0175
12. Fluid Adjusting Screw L0176
13. Pivot L0178
14. Air Feed Tube L0182
15. Gland Nut L0173
16. Gland Washer (3 pcs) L0168
17. Paint Container L0190
No. Description Part No
18. Centre Bolt Nut L0189
19. Gasket L0188
20. Lid L0187
21. Shim L0186
22. Clamp Lever L0185
23. Yoke L0184
24. Centre Bolt & Pick-Up Tube L0183
25. Trigger L0177
26. Viscosity Cup SG243
27. Spanner L0191
28. Filter (not shown) L0058
29. Air Hose (13ft) L1107
30. Hose Clip L1349
31. Handle L0041 &
L0046
33. Screw x4 (Screwdriver not supplied) L2152
Needles and fluid tips of different sizes can be obtained as sets under the following accessory numbers. Please call
our toll free helpline to order these on 888-783-2612.
0.04”/ 1.0mm dia fluid tip, needle & seal
HV5ACC10USR
0.06”/ 1.5mm dia fluid tip, needle & seal
HV5ACC15USR
0.08”/ 2.0mm dia fluid tip, needle & seal
HV5ACC20USR
0.10”/ 2.5mm dia fluid tip, needle & seal
HV5ACC25USR
The following parts are available from Earlex Inc. Please call our toll free helpline: 888-783-2612
PARTS LIST
OPTIONAL EXTRAS
Questions? Call toll free: 888-783-2612
Your Earlex Spray Station
TM
can be used with a wide variety of paints, stains and coatings such as latex, deck and
fence stain, sealers, varnishes, wood preservatives, enamels, oil and water-based paints and automotive paints.
However, some materials cannot be sprayed so please check the recommendation of the manufacturer before buying
the paint. If a material refers to brush application only then it usually cannot be sprayed.
THIS UNIT CANNOT BE USED FOR TEXTURED PAINTS. USE OF THESE MATERIALS WILL CAUSE
PREMATURE WEAR, WHICH WILL VOID YOUR WARRANTY. TO OBTAIN THE BEST RESULTS FROM YOUR
SPRAY STATION, PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE.
SELECTING PAINT
Preparation of the surface and thinning of the paint are the two most important areas to be concerned with to obtain
the best results from your spray kit. Ensure all surfaces are free from dust, dirt, rust and grease. If necessary rub down
with sandpaper, or similar. Masking of areas is important to ensure you do not spray those areas you wish to remain
untouched.
SURFACE AND JOB PREPARATION
THINNING
Your Earlex Spray Station
TM
is supplied with a viscosity cup. Viscosity is a technical term used to indicate if a product
is very thin or very thick. If thin, the viscosity is said to be low, while if very thick the viscosity is said to be high. Viscosity
is measured in seconds. In order to spray some materials they need to be “thinned” (diluted). Thinning is very important
when spraying. Most paints, etc are supplied ready for brush application and may need to be thinned (diluted) for
spraying purposes
.
The Earlex Spray Station
TM
5500 has a viscosity rating of 160 seconds. If the paint has emptied the viscosity cup
in less than 160 seconds then you will not need to thin your paint or material. If it is above this then thinning will be
required.