Installation Guide

2
eaton www.cooperwiringdevices.com
Technical Data
Effective February 2014
Aspire RF switch
Catalog No. Switch RF9501
Performance Maximum Amperage: 15A
Rating: 120V/AC, 60Hz
Uses 300 Series Z-Wave Chip @ 40Kbs
Performance Consideration An Aspire RF Z-Wave enabled device must be within 60 feet of another Z-Wave enabled device to participate in a Z-Wave wireless mesh network.
Any one dimmer or switch can be associated with up to 5 devices (dimmers, switches, receptacles, or plug-in modules)
Installation & Programming Please reference the Instruction Sheet included with the product for wiring installation. For programming of the device, see the Aspire RF User
Manual, which is provided with either the handheld (RFHDCSG) or tabletop (RFTDCSG) controllers and are also accessible online at
www.cooperwiringdevices.com/AspireRF
Testing & Code Compliance cULus Listed 244A. NOM Certified. Complies with FCC Part 15, Class B. Z-Wave Compliant Certified
Terminations Switch has four 6” wire leads for line, load, ground and neutral
Material Characteristics Flammability: Meets UL94 requirements; V2 rated
Temperature Rating:
32°F to 104°F (0°C to 40°C)
Warranty 2-year limited product warranty
Parameter Description Value range
1 Delayed OFF *0 to 127
-128 to -1
2 Panic ON time *0 to 127
-128 to -1
3 Panic OFF time *0 to 127
-128 to -1
4 Basic set value *0 to 127
-128 to -1
5 Power up state 1=OFF, 2=ON, 3=Last state
6 Panic mode enable 0=OFF, 1=ON
7 Not used Not used
*The configuration value is a signed single byte number. This value may represent a value with no units or may represent a value such as time. 0 to 127 (decimal) represents 0 to 127
seconds of time. -128 to -1 (negative decimal numbers) represents 128 to 255 seconds as calculated by this formula.
Config value = desired time in seconds (or desired value) -256
For an example of 172 seconds: config value = 172 - 256 = -84 (decimal) or 0xAC (hex)
For Parameter 4 , this value is the value that will be sent in a Basic Set command as a result from association to another device.
The Aspire RF 15A switch replaces regular switches or dimmers (where a neutral is present) to provide local and remote ON/OFF control for
LED, CFL, incandescent, magnetic low-voltage, electronic low-voltage, and fluorescent lighting loads. The Aspire RF switch provides other
programmable functions (scenes, events, association, child lockout, etc.) when used with Aspire RF or other Z-Wave® compliant control-
lers*. Each switch can be manually and remotely controlled by commands sent from an Aspire RF controller or other Z-Wave compatible
controllers or programs. An Aspire RF switch utilizes existing 120V/AC 60Hz standard house wiring and fits in a standard-sized wallbox.
Neutral wire required for installation. No new wiring needed. *Note: some specific Aspire RF features may not be programmable.
Applications for Aspire RF switch
Project Name: Prepared By:
Project Number: Date:
Catalog Number: Type:
Table 2. Specifications
Table 3. Color Ordering Information
Table 4. Device Configuration Parameters
For ordering devices, include Catalog No. followed by the Color Suffix: AW (Alpine White), DS (Desert Sand),
Silver Granite (SG), WS (White Satin), DBK (Decorator Black), DLA (Decorator Light Almond), DW (Decorator White).
Designer series color options:
Decorator series color options:
DBK DLA DW
Decorator
Black
Decorator
Light Almond
Decorator
White
AW AW DS DS SG SG WS WS
Alpine White Desert Sand Silver Granite White Satin
Compliances, specifications and availability are subject to change without notice.