Installation & Assembly

ManualsBrandsEbern Designs ManualsCandle-Style ChandeliersAliehs Candle Style Globe Chandelier

1of3

(4)CandelabraBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Assembly Instructions for Pendant Light

(Step 1A - Step 7A)

Hardware Contents

Package Contents

Crossbar Assembly

Supply Wires

and Ground Wire

STEP 3A Install Crossbar Assembly-

A. Pass the supply wires through the Crossbar

Assembly (AA). Attach the Crossbar

Assembly (AA) to the Outlet Box with the

head of the Green Ground Screw facing

you. Secure it with Outlet Box Screws (not

included). Tighten until snug.

STEP 4A Fit Ceiling Canopy to

Crossbar Assembly

Ceiling Canopy A to the

Ceiling Canopy A

ceiling

Remove mounting balls from the

Crossbar Assembly (AA). Fit the

()

Crossbar Assembly (AA) and

secure with mounting balls. Note:

The ( ) should be

snug against the and the

mounting balls. If Not, adjust the

length of the nipple on the

Crossbar Assembly (AA) by

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 2A

Figure 3A

Figure 4A

unscrewing the preassembled hex nut and lock washer and then

screwing the mounting screws in or out of the crossbar until the

correct length is achieved. Once the Ceiling Canopy (A) is secure,

remove the mounting ball and Ceiling Canopy (A) and proceed to

Step 5A.

6” Rod

Ceiling Canopy

12” Rod

Socket Assembly

Swivel

Hex Nut

Flat Washer

Nipple

STEP 1A Assemble Swivel and Ceiling

Canopy together

A. Thread the Nipple (F) onto the Swivel (D).

B. Place the Ceiling Canopy (A), the Flat

Washer (G) and the Lock Washer (H) over

the Nipple (F). Secure them with the Hex

Nut (E) and tighten until sung.

Figure 1A

STEP 2A Assemble the Rods and the Ceiling Canopy-

A. Determine the Rods (B/C) to be assembled to the Socket Assembly

(J) according to your hanging height.

B. Pass the supply wires and ground wire through the chosen rods

(B/C) and the Ceiling Canopy (A). Thread the Socket Assembly (J),

the chosen Rods (B/C) and the Ceiling Canopy (A) together. Hand

tighten until snug.

Crystal Bobeche

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

(Step 2A Continued)

Suggested rods for Ceiling

height :

8’ ceiling : use (2) 6” rods

9’ ceiling : use (2) 6” rods and

(1) 12” rod

10’ ceiling : use (2) 6” rods

and (2) 12” rods

Lock

Washer

Assembly Instruction

Summary of content (3 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) Candelabra Base Bulbs 60W Maximum Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 5A - Wire Connections STEP 2B - Install Crossbar Assembly A. Use standard wire connectors (not included) to make all wire connections. (Connectors are not included with fixture.) Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. A. Pass the supply wires through the Crossbar Assembly (AA).
PAGE 3
FINISH: WESTERN BRONZE FINISH: BRUSHED NICKEL 5” Dia. PENDANT LIGHT 58” OVERALL HEIGHT (2) 6” AND (2) 12” RODS INCLUDED 2 19.5” 3 1 18” SEMI-FLUSH 5” Dia. 22” 3 18” NO. PART NUMBER REPLACEMENT PART QTY.