Instruction v.7 Owner manual

ManualsBrandsEcho ManualsGardening equipmentLS21160

Instructions

PN 36323-00

Rev. 120112

SUBJECT: QUICK SPLIT (PN

75896-00) AND THROTTLE DOWN

(PN 75899-00) KITS

FITS MODELS: ALL LOG

SPLITTERS*

Before inspecting or servicing any part of this machine,

shut off power source, remove key, disconnect the

battery cables and make sure all moving parts have

come to a complete stop.

WARNING

1. Install the channel and angle mount assembly on the

right side of the log splitter in the channel with two

3/8 x 3/4" self-tapping hex bolts. IMPORTANT: If your

log splitter does not have the hex bolt holes already

pre-drilled, see Appendix 1 on page 8 for drilling

instructions.

2. Do not completely tighten bolts at this point. Allow

enough movement to assist in completion of

assembly

3. Pull knob on angle mount assembly out to install slider

plate into channel mount as shown in Figures 3 and

INSTALLATION

NOTE

If the throttle down kit is installed on model LS21160,

you will first need to install a new Control Assembly.

Contact your local Honda dealer to order part #

16500-ZL8-800.

Figure 1. Channel and angle mount assembly

Figure 2. Channel and angle mount assembly

Figure 3. Pull knob out to install slider plate

Figure 4. Slider plate installed

*Throttle Down Kit #75899-00 is not designed for use on LS21 and LS21E Log Splitter models

Summary of content (8 pages)

PAGE 1
Instructions SUBJECT: QUICK SPLIT (PN 75896-00) and THROTTLE DOWN (PN 75899-00) KITS FITS MODELS: ALL LOG SPLITTERS* WARNING Before inspecting or servicing any part of this machine, shut off power source, remove key, disconnect the battery cables and make sure all moving parts have come to a complete stop. NOTE Figure 2. Channel and angle mount assembly 2. Do not completely tighten bolts at this point. Allow enough movement to assist in completion of assembly 3.
PAGE 2
4. Continue to hold knob out and push the slider plate through the channel and angle mount assembly, 7. Remove the existing valve handle by removing the two pins and cottter pins that attach it to the hydraulic valve. Figure 5. Push slider plate through channel mount Figure 8. Pins to be removed on existing handle 5. Put a 1/4 x 3/4" hex bolt and nylock nut through the hole on the end of the slider plate as shown in Figure 6. Figure 9. Pins to be installed on new handle 8.
PAGE 3
NOTE Steps 13 through 22 are not applicable to Log Splitter models LS21 and LS21E. CABLE CLAMP Figure 11. Reinstall lever knob 11. Pivot the end of the newly installed slide angle up and align it with the end of the new handle. Attach them using 5/16 x 1" hex head bolt, two washers and one nylock nut. Tighten nut and bolt to the point that it still allows proper operation of handle and slide angle. Figure 13. Throttle cable installed in cable clamp 14.
PAGE 4
20. Remove the wire stop from the throttle cable by loosening the bolt. Figure 17. Coated clamp for routing of throttle cable 21. Attach the cable stop with a screw supplied with the throttle cable, a #8 washer, and a 3/16" screw to the lever bottom sheet. Tighten with an Allen head wrench (the lever bottom must be in the vertical position). Figure 15. Throttle arm friction nut 17.
PAGE 5
23. Remove the existing bottom wedge plate(A) as shown in Figure 21, by removing the 1/2 nuts and washers from the three 1/2 x 1-3/4" bolts securing it to the wedge. 24. Install the new bottom wedge plate(B) that is supplied in the Quick Split kit by reinstalling the bolts and hardware, removed in step 23, and tighten securely. A Figure 19. Quick Split 22. Hook the spring between the lever bottom sheet and the mount angle.
PAGE 6
QUICK SPLIT KIT PARTS DIAGRAM 18 13 7 7 6 8 14 24 22 3 12 9 11 21 20 4 10 2 3 10 8 13 19 23 5 *Items 2, 6, 11 and 12 are not used in apllication on Log Splitter models LS21 and LS21E QUICK SPLIT KIT (PN 75896-00) Item Description Qty.
PAGE 7
THROTTLE DOWN KIT PARTS DIAGRAM 8 6 18 17 12 8 12 19 2 16 1 3 6 14 7 15 9 5 4 10 11 13 Throttle Down kit #75899-00 is not used on Log Splitter models LS21 and LS21E THROTTLE DOWN KIT (PN 75899-00) Description Qty. 11 36088-00 CABLE, THROTTLE LOG SPLITTER 1 12 36096-00 BOLT, 3/8 X 3/4 HEX SELF TAP ZP 4 13 36387-00 SPRING, EXTENSION 1/2 X 2.00 X .075 1 14 72985 SPACER, 1/2 X .
PAGE 8
APPENDIX 1 DRILLING HOLES IN THE MOUNT PLATE If your log splittter does not have the two holes in the channel used to complete Step 1, use the dimensions below to drill two .41" x .50" holes in the mount plate. Ø .41 x .50 3.25” 2.50” 1.25” 1.25” ECHO BEAR CAT www.bearcatproducts.com 237 NW 12th Street, West Fargo, ND 58078-0849 Phone: 701.282.5520 • Toll Free: 800.247.7335 • Fax: 701.282.9522 E-mail: service@bearcatproducts.com • sales@bearcatproducts.