Instruction v.8

ManualsBrandsEcho ManualsGardening equipmentLS21160

Instruction Sheet

Instructions

PN 36278-00

Rev. 042013

SUBJECT: FENDERS WITH LIGHTS KIT

# 75908-00

FITS MODELS: LS27270, LS27270T,

LS21160, LS21160T, LS21170, LS21170T,

LS33340, LS33340T, LS21E

SN: B08086 AND BELOW

Before inspecting or servicing any part of this machine,

shut off power source, remove key, disconnect the

battery cables and make sure all moving parts have

come to a complete stop.

WARNING

These instructions will describe how to install fenders with

lights and a license plate light on a log splitter.

INSTALL FENDERS AND LIGHTS

1. Attach the fender, RH tail light angle, and clamp to the

right side fender mount as shown below with three (3)

1" hex bolts, washers, and nuts.

2. Repeat for the other side of the machine using the LH

tail light angle.

RH TAIL

LIGHT ANGLE

FENDER

MOUNT

CLAMP

INSTALL LICENSE PLATE LIGHT

1. Plug the light plug into the license plate light.

2. Attach the license plate light to the license plate angle

using one (1) 3/4" screw and 10/24 nylock nut.

3. Screw the white wire (ground) of the light plug to the

license plate light with the other 3/4" screw while

fastening it to the license plate angle (see picture

following).

LICENSE

PLATE ANGLE

LIGHT PLUG

LICENSE

PLATE LIGHT

NOTE

Enclose all exposed wire in conduit.

INSTALL LIGHT HARNESS

1. Cut the wire harness at 106" from the end of the plug.

The excess wire will be used later.

2. Cut the 103" piece of conduit into three pieces that

are 40", 48", and 15" long (see Fig. 10).

3. Bolt the clamp to the hitch as shown below by

removing the nut, adding the clamp to the bolt, and

screwing the nut back on.

4. Thread the GREEN/BROWN and YELLOW/BROWN

wires through the hitch pole leaving 24" of wire at the

hitch.

5. Ground the WHITE wire to a bolt on the hitch.

6. Run the wire out of the hitch pole and through the

clamp, as shown below.

Fig. 1. Attach the tail light angle and fender to the fender mount

Fig. 2 Attach the license plate light and angle to the log splitter

Fig. 3 Attach clamp to hitch post

4. Attach the license plate angle to the machine with (2) 1"

carriage bolts, 5/16" washers, and 5/16" nylock nuts.

Summary of content (4 pages)

PAGE 1
Instructions SUBJECT: FENDERS WITH LIGHTS KIT # 75908-00 FITS MODELS: LS27270, LS27270T, 4. Attach the license plate angle to the machine with (2) 1" carriage bolts, 5/16" washers, and 5/16" nylock nuts. LS21160, LS21160T, LS21170, LS21170T, LS33340, LS33340T, LS21E SN: B08086 AND BELOW LICENSE PLATE LIGHT WARNING Before inspecting or servicing any part of this machine, shut off power source, remove key, disconnect the battery cables and make sure all moving parts have come to a complete stop.
PAGE 2
7. Wrap the 48" length of conduit around the wires. 8. Mark the conduit at 17" from the point at which the harness and conduit exit the hitch pole. 9. Run the harness through the hole in the machine frame (see Fig. 3). 16. Where the conduit around the YELLOW wire runs out, route the YELLOW wire into the conduit with the GREEN/BROWN wire. Run this conduit to the fender (see Fig. 6). 10. At the 17" point that you marked in Step 8, take the GREEN/BROWN wire out of the conduit.
PAGE 3
HT RIG 17" 24" FT LE Fig. 9 Diagram of wiring the log splitter tail lights and license plate light 19. Run the YELLOW/BROWN wire to the left tail light the same way as the GREEN/BROWN wire went to the right tail light. 20. Strip the ends of all wires. 21. Wire the harness wires to the tail lights as follows: • • • • 24" Yellow to LH tail light (STOP & TURN) Yellow/brown to LH tail light (TAIL) Green to RH tail light (STOP & TURN) Green/brown to RH tail light (TAIL) H 48" I T 22.
PAGE 4
14 16 4 8 6 8 19 15 1 13 7 17 2 3 5 OEM NUT 10 9 20 12 18 ITEM PART NUMBER 11 DESCRIPTION QTY 1 14048-00 CLAMP, 9/16 COATED 3 2 14367-00 PLUG, 12 VOLT LIGHT 1 3 14368-00 LIGHT, LICENSE PLATE 1 4 14775-00 TIE, DOME FIR TREE 1 5 15219 BOLT, 5/16” X 1” GR5 HHCS NC ZP 6 6 15250 WASHER, 5/16” FLAT ZP 2 7 15301 BOLT, 5/16” X 1” GR5 CRG ZP 2 8 15356 NUT, 5/16” NE NYLOCK ZP 8 9 15397 NUT, 10/24 NYLOCK TYPE NM, ZP 2 10 15416 WASHER, 5/16” SAE FLT ZP 10 11