LS21160 - 21 ton hydraulic log splitter LS21160T - 21 ton towable hydraulic log splitter LS27270 - 27 ton hydraulic log splitter LS27270T - 27 ton towable hydraulic log splitter LS33340 - 33 ton hydraulic log splitter LS33340T - 33 ton towable hydraulic log splitter Manual P/N 36190-00 Rev.
Before You Begin DEAR ECHO BEAR CAT CUSTOMER Thank you for purchasing a ECHO Bear Cat product. The ECHO Bear Cat line is designed, tested, and manufactured to give years of dependable performance. To keep your machine operating at peak efficiency, it is necessary to adjust it correctly and make regular inspections. The following pages will assist you in the operation and maintenance of your machine. Please read and understand this manual before operating your machine.
LIMITED WARRANTY This warranty applies to all AG and Outdoor Power Equipment manufactured by Crary Industries. Crary Industries warrants to the original owner each new Crary Industries product to be free from defects in material and workmanship, under normal use and service. The warranty shall extend 1 year from date of delivery for income producing (commercial) applications and 2 years from date of delivery for non-income producing (consumer) use of the product.
TABLE OF CONTENTS DESCRIPTION PAGE SAFETY.......................................................................... 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 SAFETY ALERT SYMBOL......................................... 1 EMISSION INFORMATION........................................ 1 before operating............................................... 1 OPERATIon SAFETY............................................... 2 MAINTENANCE and storage safety............... 3 towing safety........................................
1 Section SAFETY The engine on your power equipment, like most outdoor power equipment, is an internal combustion engine that burns gasoline or diesel fuel (hydrocarbons). Therefore, your power equipment must be equipped with a spark arrester muffler in continuous effective working order. The spark arrester must be attached to the engine exhaust system in such a manner that flames or heat from the system will not ignite flammable material. 1.
SAFETY 7. Do not operate this equipment in the vicinity of bystanders. Keep the area of operation clear of all persons, particularly small children. It is recommended that bystanders keep at least 50 feet (15 meters) away from the area of operation. 8. Do not allow children to operate this equipment. Allow only adults to operate the Log Splitter. No one under the age of 18 should be allowed to operate the log Splitter. 9. Use only in daylight or good artificial light. 10.
SAFETY 23. When the ram of the log splitter is in the return mode, keep your hands off the machine—the log splitter is designed to automatically stop the ram when the cylinder is fully retracted. 24. Do not step across the log splitter while the engine is running. 25. Do not straddle or reach across the splitting area when operating the machine. 26. When splitting logs in the vertical position, stablize the log before engaging the control. Split as follows: a.
SAFETY 1.7 safety decal locations The numbers below correspond to the decals in Section 1.7. Familiarize yourself with all of the safety and operational decals on the machine and the associated hazards. See the engine owner’s manual or contact the engine manufacturer for engine safety instructions and decals. Make certain that all safety and operating decals on this machine are kept clean and in good condition. Decals that need replacement must be applied to their original locations.
SAFETY 1.8 safety decals See Section 1.6 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine and the associated hazards. See the engine owner’s manual or contact the engine manufacturer for engine safety instructions and decals. Make certain that all safety and operational decals on this machine are kept clean and in good condition. Decals that need replacement must be applied to their original locations.
2 Section ASSEMBLY 2.1 INSTALL THE HYDRAULIC CYLINDER The log splitter is shipped with the hydraulic cylinder moved forward on the main beam. To install the hydraulic cylinder: 1. Remove the right hand ledge tube by removing two 3/8" x 1-3/4" bolts and nylock nuts (Figure 1). 2. Remove the six 3/8" x 3/4" bolts that connect the cylinder cradle to the main beam. 3. Slide the hydraulic cylinder and valve assembly back until the ports at the ram end of the cylinder rest in the notches of the main beam. 4.
ASSEMBLY 2.3 FILL THE TANK WARNING Gasoline and diesel fuels are highly flammable and their vapors are explosive. To prevent personal injury or property damage: Store fuel only in approved containers, in well ventilated, unoccupied buildings, away from sparks or flames. A container with a capacity of 2 gallons or less with a pouring spout is recommended.
3 Section FEATURES & CONTROLS 3.1 LOG SPLITTER COMPONENTS Understanding how your machine works will help you achieve the best results when using your machine. The following descriptions define the features and controls of your machine. 1. Hitch safety chains: Safety chains are used during towing to prevent the machine from completely separating from the tow vehicle in the event the coupler detaches from the tow vehicle. Cross the safety chains under the hitch and connect to the towing vehicle. 6.
FEATURES & CONTROLS 3.2 ENGINE COMPONENTS NOTE Refer to the engine owner's manual for more detailed engine information. 1. Engine choke: Use when starting a cold engine. To use, push the lever to the left. Gradually turn off as the engine warms. Full choke may not be necessary when starting a warm engine. In this case, partial or no choke may work best. 2. Fuel cut-off switch: Push lever to the ON position to start and run engine. Push lever to OFF position when engine is not in use and during transport.
44 Section OPERATION As with any other piece of outdoor equipment, getting the feel for how your machine operates and getting to know the best techniques for particular jobs are important to overall good performance. WARNING Move machine to a clear, level area outdoors before starting. Do not operate in the vicinity of bystanders. 4.2 STOPPING THE LOG SPLITTER 1. Move the throttle to the SLOW position. 2. On 160cc engines, stop the engine by pushing the throttle all the way down to the STOP position.
OPERATION 4. Stand behind the cutting area on the control lever side of the log splitter. 4.3 operating the LOG SPLITTER WARNING Read and follow all safety instructions in this manual. Failure to operate the machine in accordance with the safety instructions MAY RESULT IN PERSONAL INJURY! CAUTION Obtain and wear safety glasses at all times when operating the machine. Do not wear loose fitting clothing. The operator should always wear heavy boots, gloves, pants and a long-sleeved shirt.
OPERATION WARNING If necessary, you may support the log on the main beam by placing your hand on the side of the log. Do not place your hand between the log and splitting wedge. Only support the log with your hand until the splitting wedge makes contact with the log. Then, remove your hand from the cutting area, stand clear and resume operation.
OPERATION 4.4 vertical operation WARNING To prevent personal injury or property damage: shut off engine and make sure that all moving parts have come to a complete stop before servicing, adjusting or repairing. Disconnect the spark plug. The main beam of the log splitter can be flipped vertically to split wood. Perform the following steps for vertical operation: 1. Turn the engine off. 2. Pull the spring-loaded pin located under the main beam (see Figure 3). 3.
5 Section SERVICE & MAINTENANCE 5.1 maintenance schedule The items listed in this service and maintenance schedule are to be checked, and if necessary, corrective action taken. This schedule is designed for units operating under normal conditions. If the unit is operating in adverse or severe conditions, it may be necessary for the items to be checked and serviced more frequently.
SERVICE & MAINTENANCE WARNING Before inspecting or servicing any part of this machine, shut off power source, and make sure all moving parts have come to a complete stop. 5.2 lubrication NOTE Lubricate the machine periodically with a lithium-based grease. Extreme working conditions will require more frequent greasing. Repack the wheel bearings with grease after every 20-25 hours of use (see Figure 6): Do not over grease bearings. Overfilling can lead to excessive heat and/or unseating of the seals.
SERVICE & MAINTENANCE WARNING Before inspecting or servicing any part of this machine, shut off power source, and make sure all moving parts have come to a complete stop. 5.3 filling HYDraulic FLUID Check the fluid level with the dipstick before each use. The hydraulic pump requires premium hydraulic fluids containing high quality rust, oxidation, and foam inhibitors.
6 Section TROUBLESHOOTING Before performing any of the corrections in this troubleshooting chart, refer to the appropriate information contained in this manual for the correct safety precautions and operating or maintenance procedures. Contact your dealer or the factory for service problems with the machine. PROBLEM Engine will not start. Engine or rotor stalls or stops. Chipper does not chip. Engine overheats. Hard to feed chipper; requires excessive power to chip.
7 Section SPECIFICATIONS 7.1 MACHINE SPECIFICATIONS LS21160 LS21160T DESCRIPTION OVERALL SIZE OVERALL WEIGHT STARTER DRIVE TYPE TIRE SIZE ENGINE FUEL TANK CAPACITY HYDRAULIC OIL TANK CAPACITY HYDRAULIC PUMP TYPE HYDRAULIC CYLINDER FORCE HYDRAULIC CYLINDER STROKE HITCH TYPE English 45.75" x 75.7" x 38.4" 380 lbs. Recoil Direct 4.8" x 8" 160cc Honda 0.48 gallons Metric 116.2cm x 192.3cm x 97.5cm 172.4 kg. Recoil Direct 12.2cm x 20.3cm 160cc Honda 1.8 liters English 45.75" x 75.7" x 38.4" 395 lbs.
SPECIFICATIONS 7.2 bolt torque The tables below are for reference purposes only and their use by anyone is entirely voluntary, unless otherwise noted. Reliance on their content for any purpose is at the sole risk of that person and any loss or damage resulting from the use of this information is the responsibility of that person. SAE Grade and Head Markings SAE - 2 BOLT DIAMETER SAE - 8 SAE - 5 A ENGLISH BOLT TORQUE * BOLT DIAMETER (A) SAE 2 SAE 5 SAE 8 N.m Ft-lb. N.m Ft-lb. N.m 1/4” 7.
ECHO BEAR CAT 237 NW 12th Street, West Fargo, ND 58078-0849 Phone: 701.282.5520 • Toll Free: 800.247.7335 Fax: 701.282.9522 • E-mail: service@bearcatproducts.com • sales@bearcatproducts.com www.bearcatproducts.
