LS21E - 21 TON ELECTRIC LS21160 - 21 ton LS21160T - 21 ton towable LS27270 - 27 ton LS27270T - 27 ton towable LS33340 - 33 ton LS33340T - 33 ton towable Manual P/N 36190-00 Rev.
Before You Begin DEAR ECHO BEAR CAT CUSTOMER Thank you for purchasing a ECHO Bear Cat product. The ECHO Bear Cat line is designed, tested, and manufactured to give years of dependable performance. To keep your machine operating at peak efficiency, it is necessary to adjust it correctly and make regular inspections. The following pages will assist you in the operation and maintenance of your machine. Please read and understand this manual before operating your machine.
LIMITED WARRANTY This warranty applies to all AG and Outdoor Power Equipment manufactured by Crary Industries. Crary Industries warrants to the original owner each new Crary Industries product to be free from defects in material and workmanship, under normal use and service. The warranty shall extend 1 year from date of delivery for income producing (commercial) applications and 2 years from date of delivery for non-income producing (consumer) use of the product.
TABLE OF CONTENTS DESCRIPTION PAGE SAFETY................................................................................................................. 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 SAFETY ALERT SYMBOL.....................................................................................1 EMISSION INFORMATION....................................................................................1 before operating...........................................................................................
1 Section SAFETY The engine on your power equipment, like most outdoor power equipment, is an internal combustion engine that burns gasoline or diesel fuel (hydrocarbons). Therefore, your power equipment must be equipped with a spark arrester muffler in continuous effective working order. The spark arrester must be attached to the engine exhaust system in such a manner that flames or heat from the system will not ignite flammable material. 1.
SAFETY 7. Do not operate this equipment in the vicinity of bystanders. Keep the area of operation clear of all persons, particularly small children. It is recommended that bystanders keep at least 50 feet (15 meters) away from the area of operation. 8. Do not allow children to operate this equipment. Allow only adults to operate the log splitter. No one under the age of 18 should be allowed to operate the log splitter. 9. Use only in daylight or good artificial light. 7.
SAFETY 23. Do not step across the log splitter while the engine is running. 1.6 towing safety 24. Do not straddle or reach across the splitting area when operating the machine. 1. Ensure the log splitter is locked in the horizontal position before towing. 25. When splitting logs in the vertical position, stablize the log before engaging the control. Split as follows: a. Place log on the end plate and turn until it leans against the beam and is stable. b.
SAFETY 1.7 safety decal locations Familiarize yourself with all of the safety and operational decals on the machine and the associated hazards. See the engine owner’s manual or contact the engine manufacturer for engine safety instructions and decals. Make certain that all safety and operating decals on this machine are kept clean and in good condition. Decals that need replacement must be applied to their original locations.
2 Section ASSEMBLY 2.1 INSTALL THE HYDRAULIC CYLINDER The log splitter is shipped with the hydraulic cylinder moved forward on the main beam. To install the hydraulic cylinder: 3/8” x 3/4” BOLTS CYLINDER CRADLE CYLINDER/VALVE ASSEMBLY 1. Remove the right ledge tube by removing two 3/8" x 1-3/4" bolts and nylock nuts. CYLINDER PORT 2. Remove the six 3/8" x 3/4" bolts that connect the cylinder cradle to the main beam. 3.
3 FEATURES & CONTROLS Section 3.1 LOG SPLITTER CONTROLS Understanding how your machine works will help you achieve the best results when using your machine. The following descriptions define the features and controls of your machine. 1. Hitch safety chains: Safety chains are used during towing to prevent the machine from completely separating from the tow vehicle in the event the coupler detaches from the tow vehicle. Cross the safety chains under the hitch and connect to the towing vehicle. 6.
FEATURES & CONTROLS 3.2 ENGINE CONTROLS NOTE Refer to the engine owner's manual for more detailed engine information. 1. Engine choke: Use when starting a cold engine. To use, push the lever to the left. Gradually turn off as the engine warms. Full choke may not be necessary when starting a warm engine. In this case, partial or no choke may work best. 2. Fuel cut-off switch: Push lever to the ON position to start and run engine. Push lever to OFF position when engine is not in use and during transport. 3.
44 Section OPERATION As with any other piece of outdoor equipment, getting the feel for how your machine operates and getting to know the best techniques for particular jobs are important to overall good performance. Move the machine to a clear, level area outdoors before starting. Do not operate in the vicinity of bystanders. WARNING 1. Check engine oil and hydraulic oil levels before starting. Move machine to a clear, level area outdoors before starting.
OPERATION 4.7 operating the LOG SPLITTER CAUTION WARNING Read and follow all safety instructions in this manual. Failure to operate the machine in accordance with the safety instructions MAY RESULT IN PERSONAL INJURY! WARNING Obtain and wear safety glasses at all times when operating the machine. Do not wear loose fitting clothing. The operator should always wear heavy boots, gloves, and pants. Keep all body parts away from the cutting area while the splitting wedge is in motion. 1.
OPERATION CAUTION Depending upon the type of wood being split, a log may not always break into two pieces and fall to the ground. If a log sticks to the wedge and starts to return with the wedge during reverse, stop the cylinder retraction and remove the wood. Care should be taken to prevent the wood piece from falling on parts of your body.
OPERATION 4.8 vertical operation 4.9 STORAGE MODE The main beam of the log splitter can be flipped vertically to split wood. Perform the following steps for vertical operation: The log splitter can be adjusted for storing in tight spaces. Perform the following steps to transform the machine into storage mode: 1. Turn the engine off. 1. Turn the engine off. 2. Adjust the support leg to the highest position or remove. 2. Flip the main beam into vertical position (see Section 4.7). 3.
5 Section SERVICE & MAINTENANCE 5.1 maintenance schedule The items listed in this service and maintenance schedule are to be checked, and if necessary, corrective action taken. This schedule is designed for units operating under normal conditions. If the unit is operating in adverse or severe conditions, it may be necessary for the items to be checked and serviced more frequently.
SERVICE & MAINTENANCE WARNING Before inspecting or servicing any part of this machine, shut off power source, and make sure all moving parts have come to a complete stop. 5.3 filling HYDraulic FLUID The hydraulic tank is located in the back of the machine. Check the fluid level with the dipstick before each use. Check the fluid on level ground with the jack stand in the down position. The hydraulic pump requires premium hydraulic fluids containing high quality rust, oxidation, and foam inhibitors.
6 Section TROUBLESHOOTING Before performing any of the corrections in this troubleshooting chart, refer to the appropriate information contained in this manual for the correct safety precautions and operating or maintenance procedures. Contact your dealer or the factory for service problems with the machine. PROBLEM Engine will not start. Engine or rotor stalls or stops. Chipper does not chip. POSSIBLE CAUSES REMEDY Improper control settings. Use proper settings. Lack of fuel. Fill fuel tank.
7 Section SPECIFICATIONS 7.1 MACHINE specifications LS21E DESCRIPTION English Metric OVERALL SIZE 45.75" x 75.7" x 38.4" 116.2cm x 192.3cm x 97.5cm 380 lbs. 172.4 kg Direct Direct 4.8"-8" Pneumatic 12 cm-20 cm Pneumatic 1.5 hp Electric 1.5 hp Electric 5 gallons 18.9 liters 2 stage, 10 gal./min. 2 stage, 37.9 L/min. 21 tons 19 metric tons 24 in. 61 cm 2 in.
SPECIFICATIONS DESCRIPTION OVERALL SIZE OVERALL WEIGHT LS27270 LS27270T English Metric English Metric 45.75" x 75.7" x 116.2cm x 192.3cm x 116.2cm x 192.3cm 45.75" x 75.7" x 38.4" 38.4" 97.5cm x 97.5cm 415 lbs. 188 kg. 430 lbs. 195 kg. STARTER Recoil Recoil Recoil Recoil DRIVE TYPE Direct Direct Direct Direct 4.8"-8" Pneumatic 12 cm-20 cm Pneumatic 4.8"-8" Pneumatic 12 cm-20 cm Pneumatic 270cc Honda 270cc Honda 270cc Honda 270cc Honda FUEL TANK CAPACITY 1.4 gallons 5.3 liters 1.
SPECIFICATIONS 7.2 bolt torque The tables below are for reference purposes only and their use by anyone is entirely voluntary, unless otherwise noted. Reliance on their content for any purpose is at the sole risk of that person and any loss or damage resulting from the use of this information is the responsibility of that person. SAE Grade and Head Markings SAE - 2 BOLT DIAMETER SAE - 8 SAE - 5 A ENGLISH BOLT TORQUE * BOLT DIAMETER (A) SAE 2 SAE 5 SAE 8 N.m Ft-lb. N.m Ft-lb. N.m 1/4” 7.
ECHO BEAR CAT 237 NW 12th Street, West Fargo, ND 58078-0849 Phone: 701.282.5520 • Toll Free: 800.247.7335 Fax: 701.282.9522 • E-mail: service@bearcatproducts.com • sales@bearcatproducts.com www.bearcatproducts.
