EW-7208APC Quick Installation Guide 09-2014 / v1.
Package Contents Before you start using this product, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s): EW-7208APC Ethernet Cable Antenna x 3 Quick Installation Guide 1 CD-ROM Power Adapter
Installation 1. Screw in the included antennas to the back of the EW-7208APC, taking care to attach the two 2.4GHz antennas to the outside and the 5GHz antenna to the center. Each antenna is labeled on the base with “2.4GHz” or “5GHz”. 2. Plug the included power adapter into the device’s DC power port and the other end into an electrical socket. 3. Ensure that the Wi-Fi On/Off switch is set to on and that three LEDs (power, 2.4GHz & 5GHz Wi-Fi) display on.
. Use a Wi-Fi device (e.g. computer, tablet, smartphone) to search for a Wi-Fi network with the SSID “edimax.setup” or “edimax.setup5G” and connect to it. iOS 4 or Android 4 and above are required for setup on a smartphone or tablet. 5. Open a web browser and if you do not automatically arrive at the “Get Started” screen shown below, enter the URL http://edimax.setup and click “Get Started” to begin the setup process. If you cannot access http://edimax.
6. Choose if you want to use your EW-7208APC in its default access point mode or in a different mode. The EW-7208APC’s five available modes are outlined below: Access Point Mode The device connects to an existing router via Ethernet cable and provides 2.4GHz and/or 5GHz Internet (wireless and Ethernet) access for your network devices. Range Extender The device connects wirelessly to your existing Mode 2.4GHz and/or 5GHz network and repeats the wireless signal(s).
7. Follow the on-screen instructions to complete setup. Refer to the user manual if you need more help.
Browser Based Configuration Interface After setup you can access the browser based configuration interface to configure or change the settings of the EW-7208APC. To access the browser based configuration interface, enter http://edimax.setup into the URL bar of a web browser on a network device which is connected to the EW-7208APC. If you can not access edimax.setup, connect the EW-7208APC to a computer using an Ethernet cable and try again. You will be prompted for a username and password.
Troubleshooting 1. In range extender mode, is my EW-7208APC dual-band? a. Yes. The EW-7208APC can extend 2.4GHz & 5GHz Wi-Fi signals concurrently, but you must connect your EW-7208APC to each (2.4GHz & 5GHz) network separately during iQ setup. During iQ Setup, you will be asked to select both a 2.4GHz & 5GHz Wi-Fi network to extend, as well as specify a new SSID (name) and password for each of the networks that your EW-7208APC’s will broadcast/extend. You can disable either 2.
Wi-Fi network name Range extender SSID Encryption Enter the SSID (network name) of your existing, hidden network. Enter an SSID for the EW-7208APC or leave it blank to use a default which consists of your existing router’s SSID (above) +"_2EX". Select and enter the encryption information for your existing, hidden network. 4. What do the LEDs mean? The LEDs can be identified by icons on the underside of the EW-7208APC.
LED Color Power LED Status Description On EW-7208APC is on. Off EW-7208APC is off. On Internet connection is ready. Factory default state, or Ethernet cable not connected, or no Internet connection. 2.4GHz Wi-Fi wireless activity (transferring/receiving data). 2.4GHz WPS is active. 2.4GHz Wi-Fi not active. White Internet Blue Flashing On 2.4GHz Wi-Fi Blue 5GHz Wi-Fi Blue Flashing Off On 5GHz Wi-Fi wireless activity (transferring/receiving data). Flashing Off 5GHz WPS is active.
7. How do I reset my device to factory default settings? a. To reset the device back to its factory default settings, press and hold the WPS/Reset button for over 10 seconds, until the white power LED begins to flash. Please wait a few minutes for the product to restart. When the device restarts, all settings will be reset.
8. I forgot my password. a. Reset the router to its factory default settings and use the default username admin and default password 1234. Default settings are displayed on the product label on the bottom of the device, as shown above. 9. My EW-7208APC has a weak wireless signal. Weak signals are usually caused by interference from other devices or obstacles blocking the EW-7208APC’s wireless signal: a. Keep the device away from other radio devices such as microwaves or cordless phones. b.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, 2009/125/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 1999/5/CE, 2009/125/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 1999/5/ES, 2009/125/ES.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: AC750 Multi-Function Dual-Band Wi-Fi Access Point Model No.: EW-7208APC The following European standards for essential requirements have been followed: Directives 1999/5/EC Spectrum : EMC : Safety (LVD) : ETSI EN 300 328 V1.8.1 (2012-06); ETSI EN 301 893 V1.7.1 (2012-06) EN 301 489-1 V1.9.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
18