USER MANUAL Robot Vacuum Cleaner iQLEAN-LR01 Thank you for choosing your electriQ robot vacuum cleaner. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
CONTENTS SAFETY 3 PARTS LIST 5 PRODUCT OVERVIEW 6 INITIAL SETUP 8 OPERATION 11 APP CONTROL 13 CLEANING AND MAINTENANCE 18 TROUBLESHOOTING 22 TECHNICAL SPECIFICATIONS 23 SUPPORT 23 2
SAFETY PRECAUTIONS IMPORTANT • • • • • • • • • • • • • • • • • • • • • Carefully read the instructions before operating the unit. Please retain the manual for future reference. This appliance is for indoor use only. Rating: This unit must be only connected to a 220-230 V earthed outlet. Always check the rating label against your electrical supply. If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, retested by a qualified electrician.
• • • • • • Do not use in an environment where there is a risk of fire or explosion. Do not use to clean printer toner spilled on the floor as this could cause fire. Before using the robot cleaner, remove any fragile objects from the floor e.g. glasses, bottles, candles, lamps. Also removes any sharp metals, needles, nails, sharp glass pieces or any other objects that could block or damage the robot. Do not place any object on the top of the robotic cleaner.
PARTS LIST Please familiarise yourself with this list before commencing operation.
PRODUCT OVERVIEW Your robot vacuum cleaner is designed for cleaning homes, small offices and other small rooms. It provides excellent cleaning for a variety of floor types including: • Wooden floors • Tiled floors • Stone floors • Short-pile carpets (less than 1.
DUST BOX HEPA Filter HEPA Filter Cover Primary Filter Filter retaining clip Electrical contacts Dust Box Side Cover CHARGING STATION Signal Indicator DC socket Charging Contacts WATER TANK Water Filler Cap Mop 7
INITIAL SET UP DUST BOX ASSEMBLY 1. Assemble the dust box side cover. Press the side cover firmly into position as shown above. 2. Close the dust box side cover: pivot the cover as shown by the arrow opposite. 3. Insert the dust box Finally, remove the protective bumper strip.
CHARGING YOUR ROBOT 1. Place the charging station against a wall on flat, level ground. Keep the charging station free of obstructions 0.5m to the left and right and 1.5m in front. 1. Connect the power supply 2. Install the side brushes paying attention to the ‘L’ and ‘R’ markings 3. Turn on Power Switch 4. Charge. There are two ways to charge the robot: a. On the charging station b. Charging directly from the power adapter When charging, the indicator light flashes.
During cleaning the robot monitors its own charge level and returns to the charging station when required. You can also put the robot into recharging mode by pressing the button on the remote control or on the app. Please note: • Do not operate the charging station in areas with strong reflections such as direct sunlight or mirrors. If this is unavoidable please cover the reflective surfaces up to 7cm from the bottom. • Please fully charge the robot before first use. Charging time is approximately 6 hours.
OPERATION The product has number of different cleaning modes to cater for different cleaning needs. The cleaning mode can be chosen on the robot host, on the remote control or on the app. AUTOMATIC CLEANING PARTIAL CLEANING ZONED CLEANING The robot will scan the immediate environment and generate a map. It will then partition the map and create a cleaning path, first of all cleaning around the perimeter and then filling in the shape with S-shape cleaning patterns.
REMOTE CONTROL On/Off Home Automatic Cleaning Forward Start/Pause Turn Left Turn Right Back Suction Power Adjustment Signal Indicator Border Cleaning (Optional) Please insert 2 x AAA batteries, not included Before using your robot vacuum cleaner: o Arrange your furniture so that your robot move around freely. o Block off hazards such as stairways and bannisters to prevent your robot from danger.
APP CONTROL Before you start: • Ensure your router provides a standard 2.4GHZ connection. • If your router is dual band ensure that both networks have different network names (SSID). The provider of your router / Internet service provider will be able to provide advice specific to your router. • Place the cleaning robot as close as possible to the router during setup. • Once the app has been installed on your phone, turn off the data connection, and ensure your phone is connected to your router via Wi-Fi.
ADD DEVICE 4. At the Device screen select the + symbol to add a device. 7. Reset the device by pressing the power switch. After restarting, press and hold the device button3-5 seconds. The device will make a confirmation tone. Click next on your phone. Note: do not attempt to connect from the charging base.Make sure that after the long press a network prompt tone is received. 5. You will now be prompted to scan the QR code which is located on the underside of your robot. 6.
10. Follow the prompts, enter the mobile phone Wi-Fi settings, connect the robot### hotspot, return to the app and wait for connection. 15 11. The WeBack home screen now lists your robot.
CONTROLLING YOUR DEVICE THROUGH THE APP THE DEVICE SCREEN The device screen is the main control screen for the cleaning robot, providing access to the controls to amend the functions and settings Status: the robot’s current activity. Back: Returns to the WeBack home screen. Settings e.g. adjust volume, set schedules, set up Alexa / Google, see following page. Constituency cleaning: Choose a specific room you want the robot to clean.
THE SETTINGS SCREEN This screen gives you the option to adjust the volume of the robot’s voice and update some of the device’s basic settings. Clear current map – clear map to start a new room. Crossing Obstacles – whether to allow robot to cross 1cm doorways and other obstacles. Breakpoint Cleaning – permit robot to break off from a cleaning job to recharge then continue the remaining clean. Voice Switch - adjust the volume of the robot’s voice. Set Remark – change the name of the Robot.
CLEANING AND MAINTENANCE DUST BOX AND FILTER CLEANING Press the dust box release button to remove the dust box Open the dust box side cover Open the dust box cover and empty contents into waste bin Open the filter cover and remove the primary filter and HEPA filter. It is not recommended to wash the HEPA filter in water.
Wash the primary filter Clean the dust box using a brush or damp cloth. Do not wash with running water as this may damage the electronics. Dry the dust box and filters. The primary filter should be washed every 15-30 days. The maximum service life of the HEPA filter is three months. Do not expose HEPA filter to direct sunlight Once dry, reassemble filters and close the dust box lid. WATER TANK MAINTENANCE Remove the water tank. Pour out any remaining water Remove the mop.
Clean the inside of the water tank. Allow the tank to air dry for 24 hours. CLEANING THE BRUSHES Open the roller brush cover assembly. Take out the roller brush Use the cleaning brush provided to cut of the haoir tangled on the roller brush.
Take off the side brush. Clean with a soft cloth. MAINTENANCE OF CHARGE TERMINALS AND WHEELS Note: the charging terminals on the charging station and the underside of the robot contain sensitive electronic components. Do not use water to clean them, use only a dry cloth. Clean the charge terminals Clean the ground sensors Clean the universal wheel Clean the drive wheels Please charge product fully before any expected long periods of inactivity.
TROUBLESHOOTING FAULT POSSIBLE CAUSE SOLUTION Robot does not charge. Poor connection between the electrodes on the base of the robot and the charging base. The charging base is switched off. Ensure contacts are clean and free from obstruction. Robot gets stuck. Robot returns to charging station without completing the cleaning. Robot does not perform cleaning work automatically as scheduled. The robot may get entangled by wires and cables on the floor, by hanging curtains and by rugs and carpets.
TECHNICAL SPECIFICATIONS Model name: iQlean-LR01 CHARGING STATION Description Parameter Size Input Output Rated Power Rated Frequency 155 x 150 x 80 mm 19V 19V 0.6A 11.4W 50/60Hz HOST ROBOT Description Parameter Size Battery Weight Rated Voltage Rated Power 330 x 96mm Lithium Ion 2.8kg 14V 32W electriQ UK SUPPORT www.electriQ.co.uk/support www.electriQ.co.
