Installation Instructions

P/N: A13957501 (1804)
For support in the U.S. call 1-877-4ELECTROLUX (1-877-435-3287) or visit www.electroluxappliances.com. For support in Canada call 1-800-265-8352 or visit www.electroluxappliances.ca.
1
Unpacking and Handling
DO NOT cart
from front
DO NOT cart
from side
Cart from rear
only with 7" min.
cart forks
2-Person carrying
straps, front-to-back
recommended
DO NOT use knee
in cabinet side to
move unit
DO NOT use open
door to lift or tip
the unit
1. Empty drum
contents.
2. Carefully
tip onto
left side.
Protect
Floor
Remove
and Save
3. Remove packing insert.
4. Return
upright.
2
Connect Water Line (Steam Dryer Only)
If this is not a steam dryer, skip to step 3.
1. Turn off water supply
to washer.
2. Remove cold water hose
from cold water supply.
Rubber Washer
3. Inspect supply hose rubber
washer, replace if worn.
4. Run water from
cold outlet to clear
contaminants.
7. Connect “Y” fixture or
extension hose to cold
supply. Tighten by hand.
5. Inspect for rubber wash-
ers. (Assembly Hose Kit P/N
5304495002 is not included
with purchase of steam model).
8. Tighten additional 2/3 turn
with pliers.
Rubber Washers
MUST BE PRESENT
6. Tighten all connections by
hand, then tighten additional
2/3 turn with pliers.
9. Turn on water and check
for leaks.
Short Hose
Water Inlet
on Dryer
Cold Water Supply
Hose to Washer
“Y” Connector
3
Connect Heat Source
Gas Dryer
Electric Dryer
IMPORTANT
Please read all safety instructions before using your new front-loading dryer. For best drying results
with your new dryer, remember to review:
 INSTALLATION INSTRUCTIONS
 USE & CARE GUIDE
WARNING
• Dryer must be properly grounded at all times.
• Vent dryer through free-flowing, outdoor-vented, metal duct system.
• Improper gas installation or LP conversion could result in injury or even death.
• Avoid back or other injury. Use more than one person to move, lift or tip the dryer.
TO INSTALLER: Leave these instructions with the customer.
*Please refer to the Installation Instruction booklet provided with this dryer for more details.
Quick Installation* for Electrolux Front Load Dryer
1. Apply approved thread sealant.
2. Wrench-tighten gas line.
3. Turn on gas.
IMPORTANT
Refer to Installation Instructions provided with
the dryer for more detailed information.
WARNING
L.P. systems must use coversion kit installed by qualified
technician.
Open
Close
Manual Shutoff
Don’t Move
White Wire
Move
White Wire
White
Wire
Green
Wire
Black
or
Red
Wire
Install
U.L.-Approved Strain Relief
30 AMP 30 AMP
4
Vent Exhaust
• Use only 4 inch (10.2 Cm) rigid metal or
semi-rigid metal ducting
• Replace plastic or foil ducts with metal
• Clean lint from present duct system before
adding on
• See chart to the right for acceptable num-
ber of 90° turns in system
• Do not use screws to connect ducts
• Do not use regular duct tape to connect
ducts, only metal foil tape
• 4" (10.2 Cm) clamp recommended for con-
nection between dryer & exhaust system
• Exhaust system must be vented outside
with approved vent hood
Number of 90° turns
MAXIMUM LENGTH*
of 4” (102 mm) Rigid Metal Duct
VENT HOOD TYPE
(Preferred)
4” (10.2 cm)
louvered
2.5” (6.35 cm)
0 125 ft. (38 m) 110 ft. (33.5 m)
1 115 ft. (35 m) 100 ft. (30.5 m)
2 105 ft. (32 m) 90 ft. (27.5 m)
3 95 ft. (29 m) 80 ft. (24.5 m)
4 85 ft. (26 m) 70 ft. (21.5 m)
IMPORTANT
For pedestal, stacked or closet installations, see
detailed installation instructions enclosed.
Correct
Incorrect
5
Level and Connect
1. Raise or lower leveling
legs.
2. Level in both directions.
3. Check stability corner to corner.
4. Connect power.
5. Open gas
valve and
check for
leaks with
soapy
water.
CAUTION
ELECTRICAL SHOCK HAZARD
DO NOT use prong adapter.
DO NOT remove ground prong.
DO NOT use extension cord.
6
Operate
IMPORTANT
Prior to using the sanitize feature (if avail-
able) on your dryer for the first time, internal
dryer parts must be conditioned to ensure
a complete sanitization of your laundry.
1. Place a wet load of towels or other durable
fabrics suitable for high temperatures into
the dryer.
2. Set the dryer for the 75 minute time
dry cycle and adjust the temperature to
sanitize.
* DO NOT install plastic or foil ducting.
If installing semi-rigid ducting, DO NOT
exceed 8 ft. (2.4m) total duct length.
• Do not screen the exhaust ends of the
vent system. No screen or grate of any
mesh size is allowed to cover the exhaust
opening.
• To vent left or right from dryer, use 90°
quick-turn elbow
• For installation in a recessed area or closet,
see complete installation instructions
• For mobile home installation, see complete
installation instructions
WARNING
Clean lint after every
load.
3. Once the cycle is
complete, remove
the load.
Your dryer is now
conditioned and
ready to sanitize
your laundry. It is not
necessary to repeat
internal dryer part
conditioning.