Electrolux Outdoor Products Via Como 72 23868 Valmadrera (Lecco) ITALIA Phone +39 0341 203111 - Fax +39 0341 581671 www.electrolux.com Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and trademarks in several countries. © Electrolux Outdoor Products Italy The Electrolux Group. The world’s No.
5 A 23 11 28 22 3 18 2 Strokes Engine totally sintetyc oil or Partner oil 14 7 16 10 6 15 4 17 2 D 9 27 26 29 32 31 1 30 13 24 33 McCulloch oil 50:1 1 ltr 5 10 15 20 40:1 2% 20 cm3 100 200 300 400 1 ltr 4 5 10 20 2,5% 25 cm3 100 125 250 500 E1 E2 12 20 19 8 5 21 A B B 5 10 E3 11 11 11 E4 m 12 13 14 c 36 m c 11
E6 E5 F1 F2 B F3 H1 42cc-46cc A H B F H2 H3 A D F4 42/46/52cc C B L F5 C I 52cc 0,095" 2,4 mm 3,0 mm STOP A H4 197" 5000 mm H5 538249344 538248960 G A 4T G 9" 230 mm C B L 538026134 538248960 4T D E I1 E7 I2 10" 255 mm I3 538026135 538248960 8T 9" 230 mm 538036711 538248960 a a b b c 8T c E9 d e f 10" 255 mm 538248960 L d e f g H 538036713 24T 9" 230 mm 80T 9" 230 mm E8 538040998 538240936 538240553 A A H H 538040953 538240936 538240553
A.
15 m Minimum safety distance 15m. Danger of kickback. The blade is capable of amputating arms and legs. Emergency stop. CAUTION! Danger of serious leg injuries. Take scrupulous care to follow the instructions in the manual. Maximum shaft speed. CAUTION! The cutting parts and muffler may get very hot and cause burns. Wait a few minutes before touching them. Use of the manual • Anyone who uses the machine should have read the entire manual with extreme care.
• possible contact with flying debris. Never use a brush cutter without its safety pole guard correctly in place. Only use blades or nylon string heads clearly marked with a maximum speed of at least 10,500 min-1. Use only original or approved accessories and spare parts, which you can purchase from our official distributors. The use of other accessories and spare parts increases the danger of injury and in this case the manufacturer has no liability for damage to persons or property.
obstacles. Use the machine holding it to the right of your body so that the exhaust fumes can escape freely without obstruction from your clothing. While working, grip the brush cutter firmly with both hands. Stand in a stable position on your feet. Keep the grips clean and dry. Do not use the brush cutter while standing on a ladder or other unstable support. You should always be able to control your balance.
Shaft fastener 1 2 3 the cutting device, or the grass itself, from flying up and striking the operator. 4 12 Use the shaft fastener every time you start the machine, fastening the connector to the supporting device. This way, the shaft will be held in place while your hands are busy with the starting procedure. Antivibration device The machine is equipped with an antivibration device (fig. A no. 30) which serves to reduce the vibrations transmitted to the operator.
Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and reach a fire, candle, burner or furnace pilot light, water heater, dryer, etc. Never store excessive quantities of fuel. E. Assembly/disassembly E1. Setting the motor on the frame 4 Position the motor so that the fuel cap faces upward and the bracket for fastening it to the frame is on one side. Screw pin A onto the motor as shown in the figure and tighten it securely.
Lower washer - e) Spacer - f) Rotating mower gauge - g) Blade locking screw (length mm 34,5). Assembly of sawtooth blade and blade guard 2 3 4 10 When using the sawtooth blade, remove guard for the line cutter head and the grass cutting blade and replace the Saw tooth blades (24 - 80 tooth) have a central base diametre of 20mm and therefore require the use of the appropriate size top flange to ensure a correct fit. The part number is detailed in the cutting attachment summary chart.
H. Routine maintenance 1 2 3 4 7 9 10 After every use In order to avoid overheating the motor, remove any dust and dirt from the slots on the cylinder cover and finds of the cylinder using a wooden scraper. Clean the backpack (if you wish, you can wash the padding after removing it from the frame). Store the machine in a dry place. After 25 hours of use Remove the filter as shown in the figure and clean it using a gentle jet of compressed air.
Drawing out the string During cutting, the nylon string wears naturally causing an increase in the speed of the engine and a reduced cutting capacity. When this happens, to bring out more string bump the head against the ground: release the throttle trigger to reduce the engine speed to less than 8000 rpm. Tap gently on the ground with the button (A) as shown in the figure and the string will come out automatically. Accelerate again.
N. Declaration of conformity The undersigned, authorized by E.O.P., declares that the following products model: type BC011 BC012 starting from the serial numbers produced from 2003 on, manufactured by E.O.P., Valmadrera, Italy, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) & 89/336/EEC (Electromagnetic Compatibility Directive), directive 2000/ 14/EEC (Enclosure V). Valmadrera, 15.12.03 Pino Todero (Technical Manager) Electrolux Outdoor Products Italy S.p.
