PE 9038-m Fully automatic espresso coffee machine Operating and Installation Instructions
ENGLISH CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 2/35 Safety instructions Description of the coffee machine Description of the control panel: touch control Instructions for the first use of the machine Making Coffee Hot water Steam Programming the amount of coffee beans to be grinded Programming the volume of coffee dispended in the cup If you wish to reset the standard values Signals and alarms Coffee menus Cleaning Installation Something not working....
1. SAFETY INSTRUCTION Please read this instruction book before using the appliance and retain for future reference. These warnings are provided in the interests of your safety, ensure you understand them fully before using the appliance. Intended use • • The appliance is intended for use in the home. If the appliance is used for purposes other than those intended or used incorrectly, no liability can be accepted by the manufacturer for any damage or injury that may be caused.
FOR INSTALLATION AND SERVICING Keep this instruction manual together with the machine for any future reference. If the machine is sold or transferred to another person, make sure that this instruction manual is given to the new user, so that he/she can become familiar with the machine’s functions and with the recommendations given. • • • This machine must be installed and connected to the mains by a COMPETENT PERSON.
CE This machine complies with the directive BT 73/23 Electrical safety rules EN 60335-1 (August 1995 - Safety for electrical household and similar appliances – General Standard) and EN 60335-2-15 (April 1996 – Specific Rules concerning the equipment for heating liquids).
THE PLUG MUST STILL BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN INSTALLED. THE APPLIANCE SHOULD NOT BE CONNECTED TO THE ELECTRICAL SUPPLY BY MEANS OF AN EXTENSION CABLE PERMANENT CONNECTION In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations.
2. DESCRIPTION OF THE COFFEE MACHINE 1. 2. 3. 4. 5. 6. 7. 8. 9.
3. DESCRIPTION OF THE CONTROL PANEL: TOUCH CONTROLS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
4 INSTRUCTIONS FOR THE FIRST USE OF THE MACHINE FILLING UP THE WATER RESERVOIR • Squeeze together the unlocking levers found under the drip tray • Gently pull the coffee machine forward from the housing by sliding it along the telescopic runners.
Hardness of water: • Before filling up the water reservoir, make sure that the decalcifying Brita filter has been soaked in cold water for at least 30 min. Follow the instructions printed on the filter package. After this operation insert the filter into position inside the water reservoir as shown in the figure. • If the machine will not be used for long periods, empty the water from tank.
• Ensure the mains ON/OFF switch(at rear) is ON • push the machine back into the housing until a “CLICK” can be heard. This indicate that the machine has been locked in position. FILLING UP THE CONTAINER WITH COFFEE BEANS • Press the unlocking levers located under the drip tray and pull the machine as it is shown in the figure. • pull the coffee machine forward from the housing along the telescopic runners .
• Pour approximately 200g of coffee beans into the container on the top as shown in the figure. • Push the machine back into the housing until a “CLICK” can be heard. This indicate that the machine has been locked in position. INITIAL START-UP • • Put the main switch in position 1 The led corresponding to the ON-OFF control will blink rapidly for 3 minutes.
• • The machine is be in stand-by mode when the ON-OFF LED is blinking slowly, it is then ready to be switched on. • Ensuring the water reservoir and the coffee beans container are full, switch the coffee machine on by pressing the on-off control and the corresponding LED stops flashing and remains lit. ADJUSTING THE TEXTURE GROUND COFFEE CAUTION • This machine is calibrated in the factory for an optimum level of ground coffee. Too “coarse” ground coffee will result in a weaker coffee.
• Pull the coffee machine forward from it’s housing by sliding it along it’s telescopic runners. • Turning the knob will adjust the coffee texture. Before adjusting, make a note of the original setting so that the machine can be reset, if required, to the factory settings. Turning the knob in the clockwise direction will lead to a fine texture for a stronger coffee. Turning the knob anti-clockwise will lead to a coarse texture for a weaker coffee.
STAND-BY MODE • Once powered and inserted into the cabinet, the machine is in stand-by mode: this will be signaled by the on/off LED blinking. • Press the start control to switch on the machine: the start LED will be illuminated. • To come back to the stand-by mode, press the start control once again. CAUTION: On start-up, the machine initiates the pre-warming phase for the first 3 minutes. During this phase the ON/OFF LED will blink quickly and the machine will be not able to execute any operation.
5 MAKING COFFEE • Press the control corresponding to the desired selection. • Press the start control within 10 seconds and the machine will make the coffee selected. The machine will stop automatically • CAUTION: the desired function will be disabled if the start control is not pressed within 10 seconds. It will then be necessary to repeat the procedure. HOW TO OBTAIN AN EXCELLENT ESPRESSO • The brewing time for an excellent espresso will be about 15 - 25 seconds.
6 HOT WATER • The steam/water pipe can be moved to the back of the cabinet when not in use. Pull forward when required. Do not touch when HOT! • To dispense hot water, place a container under the steam/water nozzle; then press the water control. • Press and hold the start control within 10 seconds until the desired amount is dispensed. To stop the water flowing, simply release the control. CAUTION: the desired function will be disabled if the start control is not pressed within 10 seconds.
7 STEAM • Press the steam control and the corresponding indicator blinks for 20 seconds. The machine will be ready to make steam when the indicator stops blinking and remains lit. • • Place a jug with the liquid to be heated under the steam nozzle. Press and hold the start control within 10 seconds and wait for the steam function to commence. HEATING LIQUIDS CAUTION: the desired function will be disabled if the start control is not pressed within 10 seconds.
8 PROGRAMMING THE AMOUNT OF COFFEE BEANS TO BE GRINDED • • This espresso machine has already been calibrated in factory to dispense the ideal measure of ground coffee for one cup of espresso. However this quantity of ground coffee can be increased or reduced, then the selected measure is stored. The programmable measure of ground coffee refers to both the espresso selection and to regular coffee selection. Put the machine on stand-by mode as described. • Keep the start control pressed for 10 seconds.
• Once you have modified the coffee ground quantity, press the start control for 10 seconds and the machine will automatically save the quantity desired and it will return to stand-by mode. CAUTION: the correct grinding time can change if a different kind of coffee is used. If any unpressed coffee powder is found when emptying the “used” coffee drawer, it means that the grinding time is too long and should be decreased.
9 • • PROGRAMMING THE VOLUME OF COFFEE DISPENSED IN THE CUP The volume of coffee dispensed can be adjusted as desired as follows: Press the espresso control. • Keep the start control pressed until the programme starts (approximately 5 seconds); the start control LED flashes. • When the desired quantity of coffee has been dispensed, press the start control. The machine will stop the cycle and the coffee measure will be stored automatically on the correspondent selection.
10 IF YOU WISH TO RESET THE STANDARD VALUES RESETTING STANDARD VALUES • This coffee machine is calibrated in the factory to make the optimum Italian espresso, the values set for the espresso coffee distribute 30 cc, the values set for the regular coffee is 80 cc. • if the standard values have to be reset from the stand-by control switch on the machine then press both the on/off and hot-water controls at the same time for 5 seconds.
11 SIGNAL AND ALARMS WATER REFILL INDICATOR • This machine has a sensor which detects when the water reservoir is empty. the reservoir empty led will illuminate. The machine will not operate until the water reservoir is refilled. VOLUMETER COUNTER FAULT • This machine has a volumeter counter which detects the amount of water distributed by the machine. If the water reservoir is empty or if the volumeter counter is faulty the reservoir empty led will blink and the machine will not operate.
FAULT INDICATOR • The machine incorporates an automatic system that, detecting a fault in operation, will illuminate all the LEDS. Switch OFF the machine and contact the nearest Service Force Centre. 12 COFFEE MENUS ITALIAN CAPPUCCINO This is a normal espresso with steam-heated milk giving the coffee a milder flavour and a rich, delicious frothy topping. Serve in a large cup. Pour some cold milk into a deep jug and heat using the steam jet.
13 CLEANING OUTER PARTS • Clean the stainless steel parts of the machine with a soft cloth without using aggressive detergents. Never use any abrasive sponges nor steel wool to clean the parts of steel. Dry well with a soft cloth. STEAM NOZZLE • Remember to clean the steam nozzle periodically as it can get internally dirty when frothing the milk. Remove the nozzle as shown in figure above and wipe it, together with its cap, using a sponge and hot water.
DRIP TRAY • • Remove the drip tray from the machine as it is shown in the figures above. Make sure that the drip tray is periodically drained to prevent any liquid from seeping out and dirtying/damaging the underlying furniture. Drip tray and relevant grill can be washed in a dishwasher. TO EMPTY THE “USED” COFFEE DRAWER It is necessary to remove the drip tray as it is shown in the figure, and drain it.
Pull open the door and remove the drawer and empty it. The drawer can be washed in a dishwasher or simply with hot water. Replace the drawer and close the door. Replace the drip tray.
WATER RESERVOIR • • • • If the machine is not used for long periods, change the water in the reservoir and drain the boiler by pressing the coffee button several times. Clean the water reservoir periodically . The water reservoir can be washed in a dishwasher. When using the Brita filter, replace it after approximately 2000 cups of coffee or at least every three months.
14 INSTALLATION BUILDING-IN Installing the machine into kitchen furniture with proper characteristics will ensure a correct operation of the equipment. Complying with the safety rules, ensure a proper protection against any contact with the electric components and with the parts protected only by functional insulation, by housing the machine correctly into the furniture.
ELECTRICAL CONNECTION • Fix the power cable onto the left side of the cabinet using one of the self-threading screws of the equipment and the proper cable clamp as shown in the figure. • Unscrew the cable clamp available on the machine. • Fix the power cable onto the machine as shown in the figure.
• Connect the power cable as shown in the figure. This machine is designed for a single phase voltage of 230V. The power supply requires only outlets of 13A fuse and a double pole isolation switch with at least 3 mm between contacts. INSTALLING THE MACHINE • Lay the U base plate of the machine on the shelf of the cabinet. • Ιnsert the L plates, compensating for any space. The width of the housing unit the coffee machine depends on the thickness of the cabinet’s sides.
• Τhey should be used to compensate for the internal width of the compartment, leading to a width of 560/570 mm. • Fix the U base plate inserting 4 selfthreading screws into the 4 front holes of the same plate. Then screw the telescopic runners to each side with the remaining 8 self-threading screw. • Insert the machine into the housing by coupling the machine to the runners fixed to the sides of the carcass.
• Slide the machine into the cabinet until the “click” indicates that it is locked into Position. 15 SOMETHING NOT WORKING..... If this machine does not work, please make sure that the fault is not due to: 1. 2. no power no water in the reservoir. If the power cable is damaged or the machine needs servicing, please contact the nearest SERVICE FORCE CENTRE 16 TECHNICAL SPECIFICATIONS • Width 594 mm • Depth 475 mm • Height 378 mm • Capacity of water reservoir 2.
17 AFTER-SALES SERVICE, SPARE PARTS AND GUARANTEE SERVICE & SPARE PARTS If you wish to purchase spare parts or require an engineer, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your telephone call will be automatically routed to the Service Centre covering your postcode area. For the address of you local Service Force Centre or for further information regarding Service Force, please visit the website as www.serviceforce.co.
GUARANTEE CONDITIONS AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 24 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
04501150 AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg Http://www.aeg.hausgeraete.
