Preface Copyright 2008 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Table of Content BEFORE YOU START ............................................................................... 2 LET YOUR COMPUTER ACCLIMATE ITSELF .............................................. 9 HEAT, COLD, HUMIDITY, AND GLARE .................................................... 9 SUITABLE PLACE TO WORK ................................................................. 10 INTRODUCTION...................................................................................... 12 FRONT VIEW ....................
SOUND CANNOT BE RECORDED .......................................................... 63 THE HARD DISK DRIVE DOES NOT WORK OR IS NOT RECOGNIZABLE ....... 64 THE HARD DRIVE IS MAKING ABNORMAL WHINING NOISES ..................... 64 THE HARD DISK DRIVE HAS REACHED ITS CAPACITY ............................. 64 THE HARD DISK TAKES LONGER TO READ A FILE ................................... 65 THE FILES ARE CORRUPTED ...............................................................
1
Before you Start Conventions of This Manual Use this manual will help you get the most from your notebook computer. If you are an experienced user of computers and/or Microsoft’s Windows operating systems, you might find it useful to read the Quick Start Guide that comes along with your accessories. If you are a less experienced user, you should through the manual carefully before using your system.
777... Make sure to use the right voltage for the power source when connecting the equipment to the power outlet. 888... Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord. 999... All cautions and warnings on the equipment should be noted. 111000... If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage. 111111...
The minimum specifications for the flexible cord are No. 18 AWG, (2) Type SPT-2, and (3) 2-conductor. B. For Japan: All components of the cord set must bear a “PSE” mark and in accordance with the Japanese Dentori Law. The minimum specifications for the flexible cord are .75m ㎡ conductors, (2) Type VCTR or VCTFK, and (3) 2-conductor. The cord set must have minimum rated current capacity of 7 A.
Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special instructions. Do not use the AC adapter near open water or other liquids. Never spill liquid into the AC adapter. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Class 1 Laser Product Appareil A Laser De Classe 1 Laserschutzklasse 1 Produkt Do not attempt to disassemble the cabinet containing the laser. The laser beam used in this product is harmful to the eyes. The use of optical instruments, such as magnifying lenses, with this product increase the potential hazard to your eyes. For your safety, have this equipment serviced only by an authorized service provider. Wichtige Sicherheitshinweise 111... Bitte lesen Sie diese Hinweis sorgfältig durch. 222...
111444... 111555... 111666... 111777... Stromnetz zu trennen und von einer qualifizierten Servicestelle zu Überprüfung.: a. Netzlabel oder Netzstecker sind beschädigt. b. Flüssigkeit ist in das Gerät eingedrungen. c. Das Gerät war Feuchtigkeit ausgesetzt. d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. f.
Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter. (2) Type VCTF oder VCTFK, und (3) 2conductor. Der Kabelsatz muss mindestens für eine Stromstärke von 7A geeignet sein. Der Wandstecker muss ein zweipoliger geerdeter Steckertyp gemäß dem Japanese Industrial Standard C8303 (15A, 125 VAC) sein. C. Für andere Länder: Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle, die in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen.
Verwenden Sie nur die in diesem Benutzerhandbuch angegebenen Stromkabel und Batterien. Werfen Sie die Batterien nicht ins Feuer, sie könnten explodieren. Informieren Sie sich über die örtlichen Bestimmungen bezüglich der Entsorgung. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird.
circulate around the case. Do not block the ventilation opening. Do not place your computer in direct sunlight. Suitable place to work Your computer will run well wherever you’re comfortable but extremes of temperature and humidity can be challenging to your system’s parts. There are some things you can tolerate that the computer can’t – things like static electricity, dust, water, steam and oil.
11
Introduction Preparing your Computer 111... 222... 333... 444... Install the battery pack Connecting the AC adapter Opening the display panel Turning on your computer Knowing your Computer With the LCD screen open, you will see several features important for operating your notebook computer.
To avoid damage to the display panel: 1. Try not to slam the display upon closing it. 2. Try not to place any object on top when it is closed or open. 3. Be sure the system is turned off or in suspend mode before you close the display panel. Front View 111... Camera Button (Optional) 222... LCD Display This LCD panel can only support up to a maximum opening of 115-120 degrees, please do not push it forcibly.
333... Internet Button 444... Silent Mode Button 555... Power / Suspend Button Press for 1~1.5 seconds to turn on the system. Press and hold for at least 4 seconds to turn off the system. Press the power / suspend button again to return from the suspend mode. 666... Speakers 777... Keyboard The keyboard differs for each territory 888... 999... 111000... 111111...
111... 222... 333... 444... Power Wireless Battery Status Hard Drive Left Views 111... CRT Port 222... USB Port 333... Microphone/Audio Line-in Jack 444... Stereo Headphone Jack 555...
Right View 111... 222... MMC/SD/MS/MS Pro Memory Card Slot (4 in 1) Enhanced USB 2.0 Port This strengthen USB power source for the USB port, the function lets users when using any other major big power consumption USB device in avoiding creating any harm to the USB port. When using any External USB Device, only use the approve cable provided by the manufacturer. Using other cable where it affect the current flow will cause undetermined damage. Not suitable to use any 3.5” or 5.25” USB ODD or HDD 333...
Connects to a TV for both 5.1 audio and video signals. When running Vista OS, there are times when you insert or unplug the HDMI cable, the system cannot recognize the HDMI device, you would not be able to hear a single sound coming out from the system, so we recommend you to make the following steps in solving this problem. Microsoft admited the problem that causing it thus provide a website that will guide you to solve this problem. 1.
2. After it is disabled, select the item once again and “Enable” it. Website: http://support.microsoft.com/kb/959458 DC In 666... 777... Kensington Lock Bottom View 111... 222... 333... 444...
19
Getting Started Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. To connect the computer to an external power source: Do not use inferior extension cords as this may result in damage to your notebook. The notebook comes with its own AC adapter.
Whenever possible, keep the AC adapter plugged into the notebook and an electrical outlet to recharge the battery. Never turn off or reset your notebook while the hard disk is in use status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your notebook before turning it back on; turning the power on and off in rapid succession can damage the notebook’s electrical circuitry.
batteries according to the manufacturer’s instructions or local laws.
To Remove the Battery Pack: Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance.
24
Using the Notebook Computer Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. Fn + F2 Fn + F7 Fn + F6 Changes Display Mode: LCD-only, CRT-only. Increases the brightness level. Decreases the brightness level. LCD Care LCD screens are delicate devices that need careful handling. Please pay attention to the following precautions: When you are not using the computer, keep the LCD screen closed to protect it from dust.
The Notebook’s Hot Key Controls Action Fn + F1 Fn + F2 Fn + F3 Fn + F4 Fn + F5 Fn + F6 Fn + F7 Fn + F8 Fn + F9 Fn + F10 Fn + F11 Fn + F12 System Control Enters Suspend Mode. Changes Display Mode: LCD-only, CRT-only. Mute/Unmute Audio/ PC beep to Output Decreases the speaker volume. Increases the speaker volume. Decreases the brightness level. Increase the brightness level.
Do not touch the TouchPad if your fingers are dirty. Do not rest heavy objects on the TouchPad or the TouchPad buttons. You can use the TouchPad with Microsoft Windows as well as nonWindows applications. Power Saving Modes This section contains information on the notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. The power system is comprised of two parts, the AC Adapter and the battery system.
Removing the Battery Pack To remove the battery pack from its compartment, please refer to Chapter 3, Inserting and Removing the Battery Pack. Preparing the Battery Pack for Use (Battery Calibration) Before using the battery pack for the first time, the Smart Battery IC within the battery pack should be calibrated in order to get accurate reporting of remaining battery life status. To calibrate the battery pack follows the instructions below: 1.
If system runs at heavy loading or in a high temperature environment, the battery may not be fully charged. You need to continue to charge it with the AC adapter plugged in until the charging LED turns off. Battery Status Windows XP has an applet in the Control Panel that will display an icon in the Windows taskbar indicating when the notebook is running on battery power or is attached to the AC adapter. This applet also displays a meter that indicates how much charge is remaining in the battery.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. Resetting the System After installing a software application package, you may be prompted to reset the system to load the changed operating environment.
Using the Windows Help Windows For Windows Vista help, click Start Help and Support icon will open the dialog box. Desktop Desktop may vary differently on the software installed in your notebook with different or additional shortcuts.
RReeccyyccllee BBiinn Used for storing deleted files in case you want to recover and save it in your system. The files will only be deleted from the Recycle Bin permanently only if you empty it by right clicking your mouse and select the “Empty Recycle Bin”. SSttaarrtt BBuuttttoonn Allows easy access to all Windows programs.
The Start menu allows you to adapt and show the programs used most frequently. If you wish to keep an item, right click the item and click Pin to Start menu. Log Off will enable the current user to log off and allows a new user to log on. Turn Off Computer allows you to shut down, restart, and Stand by modes for power saving purposes. TTaasskkbbaarr When you open a program, its icon is displayed at the taskbar for you to conveniently move between programs by clicking the relevant button.
Control Panel It is in this area that you can change how Windows looks and works. Click Start Control Panel dialog box. There are two interfaces – Classic View.
35
Internet Connection There are numerous ways to connect to the Internet. This may vary from the user’s working environment as well as system specifications.
Using a modem for Connection to Internet (optional) For more detail on the Network key, please refer to your local ISP provider and follow the procedures describe in the “ISP Installation Guide” to proceed with the installation.
Using a wired LAN for Connection to Internet 38
Using Wireless LAN Network for Connection to Internet Bluetooth Connection (optional) Bluetooth is a developing, world wide, open, short-range radio specification focused on communication between the Internet and Net devices, plus it defines communication protocols between devices and computers. It connects wirelessly to your world: In home, at work, in motion and at play. Access the internet or your e-mail account from anywhere, anytime.
This will be the display that will appear on your screen.
41
Running BIOS Setup The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). It runs and maintains a variety of hardware functions. It is menu-driven software, which allows you to easily configure and change the settings. The BIOS contains manufacture’s default settings for the computer’s standard operations. However, there are occasions when you may be required to modify the default settings in the BIOS.
BIOS Action Keys Function Key Command ESC Exit F1 General Help F10 Save and Exit ↑ ↓ + Select a field Select an item Select an item Lower value Higher value Description Leaves a sub-menu to return to the previous menu OR exits the BIOS setup while saving changes. Shows the Help Screen Saves changes and reboots the computer. Selects the next field. Selects the next upper item. Selects the next lower item. Selects the next value within a field. Selects the next value within a field.
Info Setup Advanced Setup 44
Intel Security 45
Power Setup Boot Setup 46
Exit Setup 47
48
VGA Utilities You can click the touchpad or mouse right button and select the “Properties” item. Select the “Display Settings” option to enter its window display. Click on the “Advanced Settings” tab to enter “Generic PnP Monitor on Mobile Intel ® 4 Series Express Chipset Family” window display.
50
51
52
53
54
Finger printer Application 1. Click on the Fingerprint icon located at the lower right end of the screen. 2. It is recommended that you need to setup windows password for security reason. Click on the “Yes” button to continue. 3. After you had set the “Username” and “Password”, click on the “OK” to continue. After entering on your password, click the ”Next” button to continue. 4.
Position your finger flat over the center of the sensor to achieve the best contact. Start swiping your finger smoothly and slowly from top to bottom with the fingertip press firmly as it pass the sensor. This would make the sensor read your fingertip clearly. Do not lift your finger as you swipe over the sensor.. 5. 6. You are given 3 times to practice in swiping on the fingerprinter. Click the ”Next” button to continue. Select on the above correct fingerprint.
57
3G Connection 3G is the third generation of mobile phone standards and technology. 3G enable users a wide range of more advanced service while achieving greater network capacity through improved spectral efficiency. Press the hot key combination of Fn + F12 or click the 3G application icon to start executing the application.
To disconnect, click on the “Disconnect” icon will exit the 3G application. Another way for 3G connection is by clicking on the “Menu” button.
Select the “Setting” and click on the “Internet Connections” to enter the connection window display. Click on the “Add new Connection” in case you want to connect to other telecom company.
61
Troubleshooting Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter.
Be sure all the device drivers are installed properly. For example, without the audio driver properly installed, the speakers and microphone will not work. If external devices such as USB camera, scanner, printer do not function correctly when connected to the system, it is usually the device’s own problem. Consult the device’s manufacturer first. Some software programs, which have not gone through rigorous coding and testing, may cause problems during your routine use.
Click Options and select Properties. Select Recording and click the OK button. After Click OK button, the recording volume control panel will appear. Go to [Start > Settings > Control Panel] and double-click the Multimedia icon (or Sounds and Audio Devices icon). In the Volume or Audio page, make sure that the audio codec mentioned in the spec is the default recording device.
Many browsers store files in the hard drive as a cache to speed up the performance. Check the program’s Online Help for instructions on decreasing the cache size or on removing temporary Internet files. Empty the Recycle Bin to create more disk space. When you delete files, Windows saves them to the Recycle Bin. The hard disk takes longer to read a file If you have been using the drive for a period, the files may be fragmented.
Keyboard and Mouse Problems The built-in touch pad performs erratically Make sure there is no excess perspiration or humidity on your hand when using the touch pad. Keep the surface of the touch pad clean and dry. Do not rest your palm or wrist on the surface of the touchpad while typing or using the touch pad. The built-in keyboard accepts no input Please try to make sure the system doesn’t hang up and is still working.
Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory Certain brands of memory module may not be compatible with your system. You should ask your vendor for a list of compatible DIMM. The memory module may be defective. The O/S issues an insufficient memory error message during operation This is often a software or Windows-related problem. A program is draining the memory resources.
Windows crashes or freezes when you remove the PC card Make sure you have the PC card before removing it. Double-click the Safely Remove Hardware icon at the lower right corner of the task bar and select the card you wish to stop. When you click , in few seconds Windows will prompt you to remove the card. Performance Problems The computer becomes hot In a 35oC environment, the certain areas of the computer’s back case are expected to reach 50 degrees.
USB2.0 Problems The USB device does not work Check the settings in the Windows Control Panel. Make sure you have installed the necessary device drivers. Contact the device vendor for additional support. Unable to use the External USB Device Detach the external device; insert it into the Enhanced USB port. Separate the cable with the equipment; first insert the wire into the port, then connect the device with the cable that is inserted into the Enhanced USB port.
70
Specification O O..SS..
LLAAN N CCoonnttrroolllleerr Supports 10/100/1000 Mb/Sec. MII interface W Wiirreelleessss LLAAN N Mini Card w/ PCI-E interface Intel Shirley Peak - IEEE 802.11a/g/draft-n standard compliant Lite-On/MSI - IEEE 802.11b/g standard compliant CCaam meerraa CCCCD D Support 1.3M Camera KKeeyybbooaarrdd 87 keys KB support PPooiinnttiinngg D Deevviiccee PS2 Touch Pad with 2 buttons Support gesture function (optional) LLCCD D 14.0”(16:9), LED type panel, resolution 1366 x 768 14.
SSppeeaakkeerr//M MIICC Build-in 2 speakers Internal Microphone support BBIIO OSS Supports PnP, ACPI 3.0 Support external USB flash memory card boot up. With Phoenix BIOS and 1MB flash ROM PPoowweerr M mooddee)) Maannaaggeem meenntt ((ddeeffaauulltt:: SSiilleenntt m “Smart Power II” Power Management PPhhyyssiiccaall O Ouuttlliinnee Dimension: 342 mm * 248mm * 31~35.7mm(w/ Battery) Weight: 2.4 Kg w/ 6 cell bat.
