User's Manual

ManualsBrandsELK Products ManualsElectronicsGLASS BREAK

ELK-6040 Glass Break Installation Manual Page 1

ELK-6040

Wireless Glass Break Sensor

For the latest downloadable version of this manual visit our website: http://www.elkproducts.com

Installation and Setup Guide

APPLICATION & OVERVIEW

The ELK-6040 Wireless Glass Break Sensor is designed for use with

control/transceivers that accept Elk's two-way technology; such as the

ELK-M1XRFTW. It incorporates many features designed to ensure its

reliable performance.

The 6040 listens for actual patterns of breaking glass across the full

audio band using Pattern Recognition Technology

. The factory set

recognition patterns make it possible to detect the difference between

breaking glass of framed perimeter windows in a building vs. a drinking

glass breaking within a room.

The built-in two-way radio (RF) transmits alarm, tamper, supervisory,

and low battery messages to the control/receiver. Each sensor has a

unique TXID number that is enrolled into the control during installation.

With its two-way capability, the sensor listens after every transmission

for a positive acknowledgment from the control. This makes it very

energy efficient since it does not waste energy repeating transmissions

unless they are not acknowledged.

The product is suitable for use in quiet occupied areas on a perimeter

defined zone. It features a 25-ft. (7.6m) range from sensor to glass and

its low-profile housing conceals the wireless transmitter and battery.

A simple hand clap test feature lets the user confirm that the sensor is

operational. A handheld glass break tester (not supplied) can be used

to place the sensor into range and functional test mode.

This wireless Glass Break sensor complies with the ANSI/UL 639

standard for Intrusion products. It is intended for residential indoor

dwelling unit applications and other areas approved by the authority

having jurisdiction (AHJ). It is not intended for use in industrial applications.

ABOUT THIS GUIDE

This Guide describes the installation, operation, and maintenance of this

product. Keep this document in a handy location and refer to it for

answers regarding the products functions or features. Reading this

guide is the only way to learn how to use your product wisely and to

know how to react in the event of an alarm.

PACKAGE CONTENTS

6040 Wireless Glass Break sensor

CR123A Lithium Battery

Mounting Screws and Anchors

Installation Guide

FEATURES

• Pattern Recognition Technology

• Wireless two-way communication

• Operation Alarm LED - RED (viewable from front)

• RF Acknowledge LED - Bi-Color (viewable with cover off)

• Long life Lithium battery {supplied}

• Low battery trouble signal

• Periodic Supervisory check-in

• Cover tamper protection

SPECIFICATIONS

• Dimensions: 4.25"W x 3.13"H x 1.31"D

• Sensor: Omni-directional Microphone, 360° Detection Range

• Detection Range: 25 ft. (7.6m) x 360°

• Min. Distance from Glass: 4 ft. (1.2m)

• Glass Thickness:

Plate 3/32 to 1/4 in. (2.4 to 6.4mm)

Tempered 1/8 to 1/4 in. (3.2 to 6.4mm)

Wired 1/4 in. (6.4mm)

Laminated 1/8 to 1/4 in. (3.2 to 6.4mm)

• Power: One CR123 3.0 VDC Lithium Bttery

• Quiescent Current: 25 µA (typically)

• Battery Life: 5 years

• RF Frequency: 902 - 928 Mhz channel hopping

• Supervisory check-in interval: ~64 minutes

• Storage temperature: -4 to +140° F (-20 to 60° C)

• Operating Environment: 32° to +120° F (0 to 49° C)

• Relative Humidity: 93% RH (max.), non-condensing

Pattern Recognition Technology is a registered trademark of Edwards,

a UTC Fire and Security company.

Summary of content (6 pages)

PAGE 1
ELK-6040 Installation and Setup Guide Wireless Glass Break Sensor APPLICATION & OVERVIEW The ELK-6040 Wireless Glass Break Sensor is designed for use with control/transceivers that accept Elk's two-way technology; such as the ELK-M1XRFTW. It incorporates many features designed to ensure its reliable performance. The 6040 listens for actual patterns of breaking glass across the full audio band using Pattern Recognition TechnologyTM.
PAGE 2
1. GUIDELINES FOR USE This sensor is a member of a reliable, high-quality product family using the latest technology available. Please review the information in this section to ensure you get the most out of the product. The sensor must always be in direct line of sight of all windows to be protected. It is not possible for the sensor to consistently detect breaking glass around corners or in another room.
PAGE 3
Cover Tamper Switch RF Ack (Status) RF ACKnowledge LED ELK-6040 Tamper Sensor Microphone CR123 Lithium Battery Lithium Battery Alarm / Activity LED RF ACKNOWLEDGE LED This bi-color LED IS located on the bare circuit board near the upper left side. It provides visual confirmation of the two-way acknowledge (response) from the control/transceiver and can only be viewed by removing the sensor cover.
PAGE 4
ENROLL SENSOR INTO THE CONTROL USING ONE OF THE TWO METHODS BELOW 6. ENROLLING A SENSOR USING THE M1 KEYPAD 6.1 Make sure the M1XRFTW Transceiver is powered and enrolled with the M1 Control. 6.2 Enter M1 Keypad Installer Programming and go to Menu: 14Wireless Setup 6.3 Scroll up to sub-menu:3:Learn Sel Wireless Transmtr and press Select (right arrow). 6.4 Scroll to and select an unassigned WZone (wireless zone) and press Learn (right arrow) to enroll. 6.
PAGE 5
8. TESTING It is imperative that this sensor be tested during and after installation. In addition, it should be tested in its installed location at least annually. E. The LED on the sensor will blink for the one (1) minute duration of the glass break tester mode. The one (1) minute time will restart with each activation of the glass break tester. WARNING: The M1 Control should be placed into the Walk Test mode prior to conducting any sensor tests.
PAGE 6
9. MAINTENANCE This product is design for a long service life. While the Control generally provides indications when it is time to service this product, several annual and random checks or tests are recommended. Annual - Perform a Glass Break Functional Test Random - Visually check that the Alarm LED flashes when activated by the Walk Up Test Besides Alarm indications the Control also provides Missing Transmitter and Transmitter Low Battery indications.