Certification Exhibit FCC ID: TMAELK-6051 IC: 4353A-6051 FCC Rule Part: 15.247 ISED Canada’s Radio Standards Specification: RSS-247 TÜV SÜD Project Number: 72126638 Manufacturer: ELK Products, Inc.
Wireless Carbon Monoxide Alarm ELK-6051 ELK-6051 Wireless Carbon Monoxide Alarm Instruction s Read and retain carefully for as long as the product is being used. It contains vital information on the operation and installation of your Alarm. This booklet should be regarded as part of the product. If you are just installing the Alarm, this booklet must be given to the householder. This booklet is to be given to any subsequent user.
Table of Contents page 1. Read This First ................................................................... 3 2. Carbon Monoxide – The Silent Killer .................................. 4 3. Where to Place CO Alarms ................................................ 9 4. Installation .......................................................................... 15 5. Testing / Monitoring & Maintenance .................................... 17 6. What to do when the alarm sounds ...................
1. Read This First • Congratulations on becoming the owner of an Elk Carbon Monoxide Alarm. This product is designed to help protect you and your household from the dangerous effects of Carbon Monoxide- the silent killer. • The Carbon Monoxide Alarm (CO Alarm) is powered up by carefully rotating it onto the mounting plate which activates the on/off switch. The red, amber & green lights will immediately flash in sequence to show they are working.
2. Carbon Monoxide – The Silent Killer 2.1 What is Carbon Monoxide? Many people are killed each year, and many more suffer ill health from Carbon Monoxide (CO) poisoning. CO is an invisible, odorless, tasteless and extremely toxic gas. It is produced by appliances and vehicles burning fuels, such as coal, oil, natural/bottled gas, paraffin, wood, petrol, diesel, charcoal etc.
2.3 Symptoms of Carbon Monoxide Poisoning Table A Concentration of CO in Air ppm Inhalation Time (approx) and Symptoms Developed 35 The maximum allowable concentration for continuous exposure in any 8 hour period according to OSHA *. 150 Slight headache after 1.5 hours. 200 400 1,600 Slight headache, fatigue, dizziness, nausea after 2-3 hours.
Table B: CO Alarm Response Red Light Horn/Sounder 0 ppm to < 50 ppm OFF * >50 ppm 1 flash every 3 secs. >110 ppm 2 flashes every 3 secs. >250 ppm 3 flashes every 3 secs.
Pre-Alarm (before horn sounds): When the Alarm detects over 50 ppm CO the red light flashes in accordance with Table B. This helps locate CO leaks as the unit gives an indication straight away. (Without this feature the CO level would need to be at 50 ppm CO for typically 72 minutes for an alarm sound to be given). Note the Pre-Alarm signal may be triggered by CO coming for example, from cooking with gas, from car engines or from nearby barbecues.
Table C: CO Alarm Memory Indicators Red Light Response CO Gas Level 24 Hours On Demand (Button Press) ppm > 50 ppm 1 flashes every 50 sec 1 flashes ppm > 110 ppm 2 flashes every 50 sec 2 flashes ppm > 250 ppm 4 flashes every 50 sec 4 flashes Reset Memory: Hold down the test button until the red light stops and the green light starts flashing. Cover the horn with a cloth to muffle the alarm during this time. Please note that the memory will also be reset when the unit is switched off. 3.
IMPORTANT! Specific requirements for Carbon Monoxide Alarm installation vary from state to state and from region to region. Check with your local Fire Department for current requirements in your area. 3.1 Ideally a Carbon Monoxide Alarm should be installed in: - Every room containing a fuel burning appliance, and - Remote rooms where occupants spend a considerable amount of time - Every bedroom.
300mm CO Alarm 150mm 1.5 to 3 m DEAD AIR DON'T LOCATE HERE 1.
CO Alarm CO Alarm about 1 to 2m Figure 2 Figure 3 Location in rooms with sloped ceilings, the CO Alarm should be located at the high side of the room Location in bedrooms & other rooms remote from the appliance (i.e.
3.2 Unsuitable Locations Do not place the CO Alarm in any of the following areas. (1) In the immediate vicinity of a cooking appliance (keep it at least 1 metre horizontally from it). (2) Outside the building. (3) In an enclosed space (e.g. in or below a cupboard). (4) In a damp or humid area. (5) Directly above a sink or cooker. (6) Next to a door, window, air vent or anywhere that it would be affected by draughts. (7) Next to an extractor fan. (8) Over heat sources such as radiators or hot air vents.
3.31 If locating the CO Alarm in a room with a fuel burning appliance (see figure 1) • If it is mounted on a wall, it should be located at a height greater than the height of any door or window but still be at least 150mm from the ceiling. • If it is mounted on the ceiling it should be at least 300mm from any wall or light fitting. • The CO Alarm should be a horizontal distance of between 1.5m and 3m from the potential CO source.
4. Installation Warning: The Installations of this apparatus should not be used for a substitute for proper installation, use and maintenance of fuel burning appliances including appropriate ventilation and exhaust systems. 4.1 Installation Procedure 1. Select a location complying with the advice in Section 3. 2. Remove the mounting plate from the packaging/ Alarm. 3. Place the mounting plate on the ceiling/wall exactly where you want to mount the Alarm.
7. Carefully line up the Alarm on the base, gentle press home & twist on. (see figure 4) This connects the batteries and the red, amber & green lights will immediately flash in sequence to show they are working. 8. Wait 15 seconds and then press the Test button to ensure that the Alarm works (see figure 5). 9. Install all the other Alarms similarly. 4.2 How to Tamperproof the Alarm The Alarm can be made resistant to unauthorized removal. Break off the small pillar on the base as shown in figure 6a.
It is possible to further secure or tamperproof the Alarm by using a No.2 or No.4 (2 to 3mm diameter - not supplied) self-tapping screw 6 to 8mm long to firmly lock the Alarm and its mounting plate together (see figure 7). 5. Testing / Monitoring & Maintenance Testing NOTE: Always notify your Alarm Monitoring Center prior to performing any testing. Frequent testing of the system is a requirement to ensure its continued and safe operation. To test the Alarm, press the hold the test button.
Visual Status and Self-Test The CO alarm will self-check itself and give a status update every 50 seconds if there are any problems. The status of the Alarm can also be checked on demand by using the test button. The table below shows the visual status response to both the self-check and on demand testing.
Use the narrow nozzle of a vacuum cleaner to remove fluff and other contamination from the cover slots and gas entry holes. Caution: Do not paint the CO Alarm. Remove the CO Alarm when decorating. Do not allow water or dust to contaminate the Alarm. Warning: Do not open or tamper with the CO Alarm. There are no user serviceable parts inside and this can damage the Alarm. Battery Replacement Check the ‘Replace by’ label on the side wall - if it has been exceeded replace the entire unit.
AudioLINK AudioLINK feature allows an authorized person to download information from the Alarm through by way of a mobile App. For more information on using this feature, please refer to the relevant section on www.elkproducts.com. Warning! Constant exposures to high or low temperatures or high humidity may reduce battery life. Use only batteries specified in marking. Use of a different battery may have a detrimental effect on alarm operation.
OFF Position the power switch to the ON position (See fig 9). Fill a suitable size plastic bag with smoke from the joss stick or cigarette. Insert the Alarm into the smoke filled bag and seal it closed. Within seconds, the red light will begin to flash (as per Table B) to confirm that the Alarm has detected the CO gas in the bag. ON Position To check the Alarm sound, momentarily press the test button and within seconds the horn will sound briefly.
4) After following steps 1-3, if your Alarm reactivates within a 24 hour period, repeat steps 1-3 and call a qualified appliance technician (Telephone Number) to investigate for sources of CO from fuel burning equipment and appliances, and inspect for proper operation of this equipment. If problems are identified during this inspection have the equipment serviced immediately.
- Family members (including pets) exhibiting the “flu-like” symptoms of CO poisoning described above. If any of these signs are present get the appliance checked out by an expert before further use. If family members are ill get medical help. (2) Choose all appliances and vehicles which burn fossil fuels such as coal, oil, natural/bottled gas, paraffin, wood, petrol, diesel, charcoal etc. with care and have them professionally installed and regularly maintained.
in modern houses reduces ventilation and can allow dangerous gases to build up. (10) Install CO Alarms in all the areas recommended in this booklet. (11) Recognize that CO poisoning may be the cause when family members suffer from “flu-like” symptoms when at home but feel better when they are away for extended periods. 8.
9. Getting the CO Alarm Serviced If your CO Alarm fails to work after you have carefully read all the instructions, checked the unit has been installed correctly, and ensured that it has good batteries connected, return it for repair or replacement. This should be where it was purchased, or alternatively return it in a padded box to “Customer Assistance and Information” at the nearest address given on the CO Alarm or in this leaflet. (Remove the Alarm from the mounting plate before shipping the product).
Some states or jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitations on how long an implied warranty last so the above limitation may not apply to you. Do not interfere with the Alarm or attempt to tamper with it. This will invalidate the guarantee, but more importantly may expose the user to shock or fire hazards. This guarantee is in addition to your statutory rights as a consumer. 11.
(4) CO Alarms don’t last indefinitely. CO Alarms are sophisticated electronic devices with many parts. Although the Alarm and its component parts have undergone stringent tests, and are designed to be very reliable, it is possible that parts can fail. Therefore, you should test your CO Alarm weekly. The CO Alarm must be replaced after 10 years of operation. (5) CO Alarms are not a substitute for life insurance. House-holders are responsible for their own insurance.
WARNING: THIS CO ALARM IS DESIGNED TO PROTECT INDIVIDUALS FROM THE ACUTE EFFECTS OF CARBON MONOXIDE EXPOSURE. IT WILL NOT FULLY SAFEGUARD INDIVIDUALS WITH SPECIFIC MEDICAL CONDITIONS. IF IN DOUBT CONSULT A MEDICAL PRACTITIONER. 12. Troubleshooting ALARM DOES NOT WORK WITH THE TEST BUTTON: (1) Wait 15 seconds after connecting the power before button testing. (2) Hold button down firmly for at least 5 seconds. (3) Check the Alarm is secured correctly on the mounting plate. (4) Replace batteries.
(4) Ensure there is no source of hydrogen such as batteries being charged (e.g. on boats or in Uninterruptable Power Supplies (UPS)). (5) Ensure there is not excessive smoke or fumes from devices such as Egyptian shisha, hookah or hubbly bubbly pipes, especially those that use coal or charcoal to heat the tobacco. (6) If the Alarm is fitted with an RF Module, ensure that there are no problems with the other RF interconnected Alarms and that all Alarms are housecoded correctly.
ELK-6051 Service Diagnostics Diagnostics Modes Action Red LED Yellow LED Sounder Action Low battery Press & hold button Off 1 flash 1 beep with flash Replace Batteries Faulty Sensor Press & hold button Off 2 flashes 2 beeps with flashes Replace Alarm End of Life (EOL) Press & hold button Off 3 flashes 3 beeps with flashes Replace Alarm Action Red LED Green LED Sounder LCD Display Flashes as per Table C Off Off Off Fault Checks Alarm Memory 24 hours after event Long term me
FCC AND IC COMPLIANCE STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: ELK PRODUCTS IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATION NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Contact Us Customer Service Elk Products, Inc. 3266 Hwy 70W Connelly Springs, NC 28612 Telephone: (828) 397-4200 web: www.elkproducts.com © Elk Products, Inc.
