ELK Products Wireless PIR Motion Detector Installation

ManualsBrandsELK Products ManualsHome AutomationELK Products Two-Way Wireless Home Monitoring Starter Kit

ELK-6030P PIR Installation Manual Page 1

ELK-6030P

Wireless PIR with Pet Immunity

For the latest downloadable version of this manual visit our website: http://www.elkproducts.com

Installation and Setup Guide

APPLICATION & OVERVIEW

The ELK-6030P Wireless PIR Motion Sensor features Pet Immunity for

small animals up to 40lbs. It is designed for use with control/transceivers

that accept Elk's two-way technology; such as the ELK-M1XRFTW. .

The dual element pyroelectric sensor in the 6030P detects movement

within a specific coverage area, by sensing the infrared energy that is

emitted from an intruder moving across the sensor's field of view. A

change in the infrared energy creates a temperature change in the

sensor's zones, which is then processed to determine if the occurrence

qualifies as a legitimate motion detect event. If it does then the built-in

radio will be triggered.

The two-way radio (RF) in the 6030P transmits alarm, tamper,

supervisory, and low battery messages to the control/receiver. Each

sensor has a unique TXID number which is enrolled into the control

during installation. With its two-way capability, the 6030P radio listens

after every transmission for a positive acknowledgment from the

control. This makes the sensor very energy efficient since it doesn't

waste battery power repeating transmissions unless they are not

acknowledged.

Like all battery powered motion detectors, the 6030P has a mandatory

sleep cycle function to help extend the battery life. After detecting

motion, the sensor's radio will transmit the event to the control and wait

for acknowledgment. Upon acknowledgment the sensor will enter the

mandatory sleep cycle. During the sleep cycle time it cannot transmit

additional events. There are two (2) time choices for the sleep cycle

selected via DIP Switch #4. After the sleep cycle expires the sensor will

once again be capable of transmitting a new event.

The 6030P introduces the industry's first Security/Convenience Light.

This bright white LED projects a beam of light out in front of the sensor.

The modes of activation/operation are: Quick blip when motion is

detected and walk test mode is active. Flash during an audible alarm

activation. On Solid for several seconds when Control is Armed Away

and motion is detected. On Solid for several seconds when motion is

detected (regardless of armed state) and Control Output #4 is On. Flash

for several seconds by command from Control (use as a special

attention grabber or general purpose indicator). On Solid for several

seconds by command from Control (can be used to help illuminate the

immediate area for cameras, etc.)

FEATURES

• Wireless two-way communication

• Dual element pyroelectric sensor

• Pet Immunity up to 40lbs

• Selectable pulse count

• Selectable Hi/Lo range

• Excellent immunity from white light, RF, and ESD interference

• Bi-Color RF Acknowledge LED (Green + Org/Red)

• Security/Convenience

LED (White)

• Long life Lithium batteries {supplied}

• Low battery trouble signal

• Sleep Cycle "Battery Saver" (2 time settings)

• Periodic (64 min.) Supervisory check-in

• Cover tamper protection

• Swivel mounting bracket included

• Optional deluxe 90° swivel bracket for ceilings sold separately

SPECIFICATIONS

• Dimensions: 2.8"W x 4.4"H x 1.9"D

• Mounting Height: 6 1/2 to 7 1/2 ft

• Sensor: Dual element pyroelectric

• Coverage: Hi Range = 40 ft x 40 ft (12.2m x 12.2m) @ 90°

Lo Range = 30 ft x 30 ft (7m x 7m) @ 90°

20 dual element zones (10 Long, 4 intermediate, 4 mid, 2 short)

• Pulse Count: 1-2 or 3-4, selectable

• Sleep Time: Selectable 30 sec. or 120 sec.

• RF Signal Acknowledge Indication: Bi-Color LED

• Security/Convenience Light: White LED

• Warm Up Period: 10 seconds

• Operating Voltage: 3.0 Volts DC

• Battery Type & Size: 2 x Lithium CR123A

• Quiescent Current: < 10 µA

• Operating Temp: 32° to +120° degrees F

• Humidity: 95% RH (max.), non-condensing

• Frequency: 902 - 928 Mhz channel hopping

PACKAGE CONTENTS

1 - 6030P PIR electronics assembly & back housing

1 - Standard swivel bracket, locking disc, screws & anchors

1 - Blanking plug

2 - CR123A Lithium Batteries

1 - Cover locking screw

1 - Bracket screw (#4 x 3/8", pan head, sheet metal)

UNIQUE 'INDUSTRY FIRST'

SECURITY/CONVENIENCE LIGHT

Pet Immunity

40 lbs.

Summary of content (4 pages)

PAGE 1
ELK-6030P Wireless PIR with Pet Immunity APPLICATION & OVERVIEW The ELK-6030P Wireless PIR Motion Sensor features Pet Immunity for small animals up to 40lbs. It is designed for use with control/transceivers that accept Elk's two-way technology; such as the ELK-M1XRFTW. . Installation and Setup Guide 40 lbs.
PAGE 2
GUIDELINES FOR USE INSTALLATION The 6030P Sensor is for indoor use only. It may be mounted directly on a wall or in a corner, with or without the supplied swivel bracket. 1. DETACHING THE BACKPLATE - Push in the retainer tab and lift the front away from the backplate. It is recommended that the 6030P be installed within 100 feet of the control/transceiver. An open-air range of 400 feet or more is possible, but environmental conditions can reduce the actual transmission range.
PAGE 3
4. SENSOR ENROLLMENT FROM ELKRP 5. DIP SWITCH OPTION SETTINGS 4.1 Launch the ElkRP PC software and open the desired Customer Account file. ON OFF 6 4.2 Click the "+" next to Zones (Inputs) to expand the view. Look to see if there are any existing wireless zone groups. If there are none then it will be necessary to add or create a new group. To create a wireless group, right click on Zones (Inputs) and click New Wireless Zones. Place a check mark in the box to be added, starting with Group 2.
PAGE 4
ANTI-TAMPER SWITCH This switch detects the separation of the front housing from the backplate, resulting in a signal being transmitted to the control/transceiver that will cause the associated zone to become violated. Snapping the front housing back onto the backplate will transmit a restoral. FUNCTIONAL 'SYSTEM' TESTING A system test should be done by physically walking across the 6030P coverage pattern while the system is fully armed. NOTE: Allow time for the Sleep Cycle Timer to expire before testing.