EZSTLG8WS*1B LZSTLG8WS*1B INSTALLATION & USE MANUAL Manual de instalación y uso Manuel d’installation et d’utilisation EZ ™ & LZ™ Series Versatile Bottle Filling Stations & Coolers EZ™ & LZ™ Serie versatil Botella Bombas y Enfriadores EZ™ & LZ™ Stations versatile de Remplissage de Bouteille Série et Refroidisseurs *Versatile Cooler Model LZSTLG8WSLK alternate installations *Versatile Cooler Model LZSTLG8WSLK configuration as shipped *Versatile cooler design allows units to be installed either left-hand
EZSTLG8WS*1B LZSTLG8WS*1B Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. En la foto, la unidad sólo sin relleno botella. Sur la photo, est une unité seulement sans remplissage de la bouteille.
Fig.
1000001714 (Rev.
Page 5 OPTIONAL FILTER E B CL 7” (178mm) 2” (51mm) 5-3/4” (146mm) 7” (178mm) FINISHED FLOOR D (ALT.
1000001714 (Rev. M - 09/20) E OPTIONAL FILTER A (ALT.
EZSTLG8WS*1B HANGER BRACKETS INSTALLATION 1) Remove hanger brackets fastened to back of cooler by removing one (1) screw. 2) Mount the hanger brackets as shown in Figures 2, 3, 4 or 5. NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Anchor hanger securely to wall using all six (6) 1/4 in. dia. mounting holes. INSTALLATION OF COOLER 3) Hang the cooler on the hanger bracket.
EZSTLG8WS*1B LZSTLG8WS*1B Service Instructions Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
EZSTLG8WS*1B LZSTLG8WS*1B 7/16” BOLT HOLES FOR FASTENING UNIT TO WALL UNIT CENTER LINE TOP COVER Fig. 8 MOUNTING SCREWS 29 Fig. 9 BRACKET & SCREWS Fig. 10 Fig. 11 Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 9). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. 2) Remove wall mounting plate from Bottle Filler.
EZSTLG8WS*1B LZSTLG8WS*1B BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1) To verify the software program of the control board the unit will need to be shut down and restarted. The chiller (if present) does not need to be shut down and restarted. 2) The units lower panel must be open to access the power cord and wall outlet. 3) Shut down the unit by unplugging the power cord from the wall outlet. 4) Restart the unit by plugging the power cord back into the wall outlet.
EZSTLG8WS*1B LZSTLG8WS*1B INSTRUCTIONS TO MOVE THE BOTTLE FILLER & BASIN TO THE LEFT SIDE (NON-REFRIGERATED) FOR ALTERNATE MOUNTING VERSATILE BI-LEVEL Using a 5/16" socket, remove the (4) screws from the bottom of each cooler to remove the wrappers. Using a #T20 (6 point star bit), loosen the shroud screws. Both sides, both coolers. ONLY move the filler panel and j-clip to the refrigerated (right) side if right side will be mounted 'high'.
EZSTLG8WS*1B LZSTLG8WS*1B INSTRUCTIONS CONTINUED..... Swap drain parts in shroud: Loosen each hose clamp retaining the drain pieces. Remove each drain piece and swap to other basin. Tighten each hose clamp. Refrigerated Cooler side: Carefully tip the shroud/basin assembly toward the cooler frame. Connect one of the black wires to the solenoid valve and one wire to the cold control. Re-connect the water line at the solenoid valve. Reference (Fig. 17, p.17) for the operation of the quick connect fittings.
EZSTLG8WS*1B LZSTLG8WS*1B Versatile Wrapper and Trim Kit Installation Instructions Left Hand Wrapper (High Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Screw trim piece to wrapper with (2) screws (provided) 3) Re-install wrapper with (4) screws. 4) Dispose of unused Right Hand Wrapper (Low Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Clip cover plate, sliding until plate sits flush with the wall. 3) Re-install wrapper with (4) screws.
EZSTLG8WS*1B LZSTLG8WS*1B PLUMBING DIAGRAMS VERSATILE BI-LEVEL Barb capped when not used Bottle Filler Drain Bottle Filler Drain Barb capped when not used Bottle Filler Drain Barb capped when not used Bottle Filler Drain Barb capped when not used 1000001714 (Rev.
Page 15 Solenoid Valve Tee Solenoid Valve 3/8” Water Inlet Evaporator 3/8” Water Line from Bottle Filling Unit R.H. Refrig. unit EZ Bi-Level Plumbing Diagram after Filter Installation & Bottle Filler Water Line Addition H Water Inlet Bubbler L.H. Non-Refrig unit Solenoid Valve H Tee 1/4” Union Filter Assembly Bubbler L.H. Non-Refrig unit 3/8” Water Inlet Bubbler Standard EZ Bi-Level Pressurized Plumbing Diagram Solenoid Valve Evaporator R.H. Refrig.
EZSTLG8WS*1B LZSTLG8WS*1B NOTE: When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten. 11 NOTA: Basin Estanque Bassin Locknut Tuerca de Fijación Écrou de Blocage BUBBLER DETAIL DETALLE DEL GRIFO DETAIL DU BARBOTEUR Al instalar el grifo y pedestal de reemplazo, apriete la tuerca unicamente para mantener las piezas en una posicion adjustada. No dede apretarse demasiado.
EZSTLG8WS*1B LZSTLG8WS*1B OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSHIN IN SIMPLY PUSH TUBE TO TUBE TOATTACH ATTACH A A TUBE TUBEIS IS SECURED SECURED INPOSITION POSITION IN PUSH PUSHIN IN COLLET COLLET TORELEASE RELEASE TUBE TUBE TO B C PUSHING BEFORE PUSHINGTUBE TUBE IN IN BEFORE PULLING TO PULLING IT IT OUT OUT HELPS HELPS TO RELEASE RELEASE TUBE TUBE Note: Screw the locknut hand tight to seal Fig. 16 Fig. 17 WALL MOUNTING PLATE BOTTLE FILLING UNIT 3 3/8” Water Inlet 2 2 1 Fig.
EZSTLG8WS*1B 115V PARTS LIST/ 115V LISTA DE PIEZAS/ 115V LISTE DES PIÈCES ITEM PART NO. NO.
