Instructions / Assembly

12
INSTALL
CLOSER
(Right Hand)
12
1. Position base from installation kit onto door
jamb by touching front of base to back of
hinge rail (or as close as possible), and align
the bottom of the base with top of sweep.
Mark the hole locations on door jamb.
2. Using the 1/8” drill bit, drill holes in door
jamb at the marked locations.
3. Attach the base to door jamb with two 2”
screws from installation kit into the two
holes closest to the interior of the house.
1. Attach closer door bracket to the door
through the two pre-drilled holes using two
#12 x 5/8” screws.
1. Pin bump closer in place using the short pin
in the jamb bracket arm and the long pin in
the door bracket.
1. Attach the arm from the installation kit to
the base by inserting the tabs on the arm
into the slots in the base. Fasten with a 2”
screw from the installatio kit.
ba
d
c
OPPOSITE VIEW
OTRO PUNTO DE VISTA
VUE DE FACE
i
VIEW
i
VIEW
i
VIEW
i
VIEW
E
E
1/8”
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Tools needed:
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
x 4
5/8”
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
x 2
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
x 2
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
N
x 6
2”
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
a
1. Open the door and then let it close. Note the speed at which the
door closes.
2. Using a Phillips head screwdriver to adjust the closer to the
desired speed:
For a faster closing speed, turn the adjustment screw to the left
(counterclockwise).
For a slower closing speed, turn the adjustment screw to the
right (clockwise).
3. Test the speed at which the door closes after each adjustment.
Adjust the screw more, if needed, to achieve the desired door
closing speed.
ADJUST
CLOSING
SPEED OF
DOOR
Closer and door shown
are for reference only.
13
Tools needed:
Storm door will close more quickly when entry door is open. To achieve the proper closing speed, you will need to adjust
the closer(s) using the built-in adjustment screw. Check for safe closing speed with your entry door in both the closed and
the open position. To prevent injury, make sure people and/or pets are completely through the opening before allowing
the storm door to shut freely.
WARNING
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
i
VIEW