Emulex Drivers, Software and Manuals LP9402DC Installation and Reference Manual Table of Contents Installation Compatability Prerequisites Install HBA Attach Media Apply Power View LEDs Reference Specifications FCC and Regulatory Notices Declaration of Conformity Laser Safety 1
Emulex Drivers, Software and Manuals Chapter 1 − Installation Table of Contents Compatability Prerequisites Install HBA Attach Media Apply Power View LEDs 2
Emulex Drivers, Software and Manuals Installation Caution Emulex LightPulse ® Host Bus Adapters (HBAs) contain electronic components that can be damaged by static electricity through an electrostatic discharge (ESD) event. To prevent ESD damage, maintain constant contact with any grounded metal surface. A grounding wrist strap is useful for this purpose. Handle the card carefully at all times and preferably by the edges.
Emulex Drivers, Software and Manuals Install the Host Bus Adapter Board 1. Record IEEE and serial numbers. Each host bus adapter port is shipped with a unique address identifier called the IEEE address. Since this adapter has two ports, there are two IEEE addresses. The IEEE address is used when configuring your system. The serial number is used when communicating with Emulex. All numbers are clearly marked on the board. We recommend that you record these numbers before installing the adapter. 2.
Emulex Drivers, Software and Manuals Attach Media Note The host bus adapter will not allow normal data transmission on an optical link unless it is connected to another similar or compatible laser product (that is, multimode to multimode.) Use multimode fiber optic cable used with short−wave lasers, that adhere to the following specifications: Fiber Optic Cable Maximum Length Minimum Connector Length 62.5/125 µm (multimode) 300 meters at 1.0625 Gb/s 150 meters at 2.
Emulex Drivers, Software and Manuals Apply Power 1. Verify that the host bus adapter is securely installed in the computer. 2. Verify that correct media is attached. 3. Observe LEDs for Power On Self Test (POST) results. View LEDs An LED is located on the upper rear corner of the board. This LED indicates 3.3v power. Green and yellow light emitting diodes (LEDs) can be seen through openings in the host bus adapter's mounting bracket.
Emulex Drivers, Software and Manuals Chapter 2 − Reference Table of Contents Specifications FCC and Regulatory Notices Declaration of Conformity Laser Safety 8
Emulex Drivers, Software and Manuals Reference Specifications Parameter Range Media Interface Dual LC connector Physical Dimensions PCI Short form factor (full height) 6.875" x 4.2" Power Requirements 16 watts (typical) @ + 3.
Emulex Drivers, Software and Manuals FCC and Regulatory Notices CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A` LASER DE CLASSE 1 The above statement applies to products marketed in the European Union. Model LP9002 / LP9002L / LP952L / LP9002S / LP9002DC / LP9002C / LP9402DC (2x5 SFF Models) This device complies with Part 15 of the FCC Rules.
Emulex Drivers, Software and Manuals This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Paul Folino, President & CEO, Emulex Corporation, 3535 Harbor Blvd.
Emulex Drivers, Software and Manuals Translation: This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. LP9002/LP9002L/LP952L/LP9002S/LP9002DC/LP9002C/LP9402DC (2x5 SFF models) Translation: This is a Class A product.
Emulex Drivers, Software and Manuals Declaration of Conformity LP9002 / LP9002L / LP952L / LP9002S / LP9002C / LP9002DC / LP9402DC−F2 (2x5 SFF models) Note Changes or modifications not expressly approved by Emulex Corporation could void the user's authority to operate this equipment. This equipment complies with CISPR22/EN55022 Class A. Warning This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures.
Emulex Drivers, Software and Manuals EMC: FCC Rules, CFR Title 47, Part 15, Subpart B, Class A Industry Canada, ICES−003, Class A EN55022 (1998) / CISPR−22 (1997), Class A EN55024 (1998) AZ/NZS 3548: Class A and VCCI, Class A Supplementary Information: 1. The product was tested in a typical configuration with shielded cables. 2.
Emulex Drivers, Software and Manuals Laser Safety Notice This laser safety information contains certification and product information covering laser products known as optical Gigabaud Link Modules (GLMs), Gigabit Interface Converters (GBICs), 1x9 and small form factor transceivers sold as accessories to or incorporated in Emulex LightPulse host adapters. The GLM, GBIC, 1x9 and small form factor transceiver are the primary cable connection mechanisms for any optical port on the host adapter and hub.
Emulex Drivers, Software and Manuals In Europe, all optical GLMs, GBICs, 1x9 and small form factor transceivers sold by Emulex are certified as Class 1 laser component assemblies that conform to the requirements contained in the CENELEC (European Committee for Electrotechnical Standardization) standard EN60825−1:1994 (including amendment 11) and EN60825−2:1994.
Emulex Drivers, Software and Manuals Product Information GLM GBIC 1 x 9 Transceiver Small Form Factor Transceiver GLM The optical GLM is a single port communications card. Each communication port consists of a transmitter and receiver optical subassembly. The transmitter subassembly contains a semiconductor laser diode of gallium aluminum arsenide (GaAlAs).
Emulex Drivers, Software and Manuals maintenance, service operations or adjustments can be performed the GBIC. Small Form Factor Transceiver The small form factor transceiver is an integrated duplex data link for bi−directional communications over multimode or single mode optical fiber. Each small form factor transceiver consists of a transmitter and receiver optical subassembly.
Emulex Drivers, Software and Manuals GLM The GLM is designed and certified for applications using point−to−point optical fiber links only. Use of the product with multiple input or multiple output optical links (for example, star couplers) is prohibited since it is incompatible with the GLM’s certification. The GLM will not allow normal data transmission on the optical link unless it is connected to another similar GLM or compatible laser product.
Emulex Drivers, Software and Manuals Class 1 laser product. Any system level product that incorporates the small form factor transceivers must provide power supply protection that guarantees a voltage of 5.0 volts or less at the small form factor transceivers. The functional power supply range of the small form factor transceivers product is specified as 3.135 to 3.465V typically. Operation outside of this range may degrade the performance and lifetime of the transceiver.
Emulex Drivers, Software and Manuals System Level Certification All GLMs and GBICs sold as accessories by Emulex or host adapters containing embedded 1x9 or small form factor transceivers are certified as Class 1 laser products within the U.S. and Class 1 laser component assemblies outside of the U.S. Manufacturers of products properly incorporating the GLM, GBIC, 1x9 or small form factor transceiver do not need to recertify their product for laser safety.
