Manualshelf

User Manual

ManualsBrandsEnerdrive ManualsBattery ChargersePOWER 24V 30A DC to DC Battery Charger
123
Press SEL
to change
battery type
Press SEL
to change
battery type
Press SEL
to change
battery type
Press SEL
to return to
battery type
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press SET to keep the
current setting and
toggle to the next menu
Press and hold MENU button for
3 seconds to enter the
Charger Function Menu
For Lithium and Program
Battery Types refer to
Appendix A2
Press SEL
to enter low
current menu
Press SEL
to enter
mode menu
Press SEL
to enter
temp menu
Press SEL
to change
current
Press SEL
to change
mode
Press SEL
to change
temp
Press SEL
to change
temp
Press SEL
to return
to change
current
Press SEL
to return to
change mode
Press SEL
to return to
change temp
Press SEL
to return to
change current
Appendix A1
VERSION: REV. 1.0
Charger conguration is a simple step by step process as shown below.
For Tech Support call Enerdrive on 1300 851 535
NOTE: The current setting below is based on the EN3DC30-24 battery charger.
NOTE: At any function setting, pressing the MENU button will exit the function mode.
WARNING: FIRE HAZARD
When choosing the battery type and setting the charging parameter, please consult the battery manufacturer on all the voltage and
current settings. Using the wrong setting to charge a battery may overcharge, damage the battery and may cause a re.
* Disregard the
Temp Select
setting if the
Temperature
Sensor is NOT
connected.
Display will show recent setting.
CH1 BATTERY TYPE
CH1 BULK
CURRENT
CH1 CHARGE MODE
CH1 TEMP. SELECT
CH1 ABSORPTION
TO FLOAT CURRENT
Display shows GEL & Bulk
Voltage as currently set.
Display shows Bulk Current as
currently set.
Display shows Absorption to
Float as currently set.
Display shows
Charge Mode as
currently set.
Shows Temp Mode
current setting.
Press SEL
to enter high
current menu
Press SET to keep the
current setting and return
to the top level menu
Press SET to keep the
current setting and return
to the top level menu
Press SET to keep the
current setting and return
to the top level menu
Press SET to keep the
current setting and return
to the top level menu
Press SET
to keep the
current setting
and toggle to
the next menu
Press SET
to keep the
current setting
and toggle to
the next menu
CH1 Battery Type
Please choose the type of battery to be charged.
Your choices are GEL, AGM, Flooded, Lithium or
Custom Program
CH1 Absorption to Float Current “L” Setting
This setting is used to determine when the battery
is full. Once the current ow reaches this number or
below, the charger deems the battery to be full and
will shift the charger to the oat state. If running
constants loads i.e. Fridge etc, set the charger to the
highest “L” number: Choose between.3 to 6A
(Subject to H setting see page 12)
Press SEL
to change
current
CH1 Bulk Current “h” setting
This setting is used to determine the maximum
output current that the charger is capable of.
Choose between 5 to 30A
LEAD ACID MODE

Summary of content (3 pages)