XC-Series Cordless Hydraulic Pump Instruction Manual 3
General Safety Contents General Safety Electrical Safety Installation Use Operation Disconnecting Oil Fill Pressure Setting Technical Specifications Troubleshooting Important 4 6 7 8 9 10 11 12 13 14 Safety First Read all instructions, DANGER, WARNING and CAUTION paragraphs carefully. Follow all safety precautions to avoid personal injury or property damage during system operation. Save these instructions.
General Safety WARNING Indicates a potential danger that requires correct procedures or practices to avoid possible serious personal injury or death. Immediately replace worn or damaged parts with genuine ENERPAC parts. Non genuine ENERPAC parts may break, causing personal injury and property damage. ENERPAC parts are designed to fit properly and withstand high loads. Stay clear of loads supported by hydraulics. A cylinder, when used as a load lifting device, should never be used as a load holding device.
Electrical Safety WARNING Additional Warnings for Battery Operated Electric Pumps. Do not operate the pump in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The pump creates sparks which may ignite the dust of fumes. Do not expose the pump to rain or wet conditions. Water entering the pump will increase the risk of shock.
Installation 1 2 11/16" & 15/16" 4 3/8” NPTF 3 60 - 70 Nm 44 - 53 ft lb 5 6 60 Min = 100% 7 Gauge Recommended
Use 1 2 3 Optional Strap Shown 8
Operation 1 2 3 P 4 9 5 6
Disconnecting P 1 4 10 2 3
Oil Fill P 1 2 3 4 5 6 1/4" 11 < Ø13mm Pour slowly 4.5 - 5.
Pressure Setting Factory Setting User Adjustable PMAX = 700 bar/10,000 psi/70 MPa 1 Flat head screwdriver PMAX = 700 bar/10,000 psi/70 MPa 3 Pmin = 150 bar / 2,175 psi / 15 MPa 12 2 7/32" x 6"
Technical Specifications Cylinder / Tool Charger Voltage 1 PH, 50/60Hz * Valve 115 V Single acting 230 V Manual 3 way, 2 position --- Usable Oil Capacity Litres Weight in³ kg lb Model Number 1,0 60 9,9 21.9 XC-1201MB 2,0 120 10,8 23.8 XC-1202MB 1,0 60 9,9 21.9 XC-1201ME 2,0 120 10,8 23.8 XC-1202ME 1,0 60 9,9 21.9 XC-1201M** 2,0 120 10,8 23.8 XC-1202M** * For more information visit www.milwaukeetool.com ** Batteries and Charger not included.
Troubleshooting Problem Pump will not start. Pump clicks when trigger is depressed, but does not start. Low fluid output. Cylinder will not advance or retract. Pump slows down and stops. Cylinder advances and retracts erratically. Pump pulses and/or stops during prolonged or heavy operation. Possible Cause Solution Battery pack not installed. Install battery pack. Electrical contacts dirty or corroded. Clean contacts on the battery, pump and charger. Battery pack discharged. Charge battery.
xxxxx Australia and New Zealand Actuant Australia Ltd. Block V Unit 3, Regents Park Estate 391 Park Road, Regents Park NSW 2143 (P.O. Box 261) Australia T +61 297 438 988 F +61 297 438 648 sales-au@enerpac.com Brazil Power Packer do Brasil Ltda. Rua Luiz Lawrie Reid 548 09930-760 - Diadema (SP) T +55 11 5687 2211 F +55 11 5686 5583 Toll Free: 0800 891 5770 vendasbrasil@enerpac.
