Installation Instructions

ManualsBrandsEngenius ManualsOtherENS1200

Quick Installation Guide

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wiabc.com

Disclaimer: Information may be subject to changes without prior notication.

https://www.linkedin.com/company/engeniuseurope

https://plus.google.com/+EngeniusEuropeBVDeMeern

https://www.youtube.com/user/engeniuseuropebv

https://twitter.com/engeniuseu

ENS1200

Package content

Unpack the box and verify the content:

- ENS1200

- PoE injector

- Power adapter

- Quick Start Guide

- Wall mount screw set

- 2* Pole mounting strap

Minimum requirements

- Broadband Internet Service (cable or DSL modem)

- Internet browser (Internet Explorer, Safari, Firefox, Chrome)

Connecting the ENS1200

1. Remove the rear bottom panel.

2. Connect one end of the Ethernet cable into the LAN(PoE) port of the access

point and the other end to the PoE Ethernet port on the PoE injector.

3. Connect the power adapter to the DC-IN port of the ENS1200 and plug the

other end into an electrical outlet.

4. Connect the second Ethernet cable into the LAN port of the PoE injector and

the other end to the Ethernet port on the computer.

5. Place the panel removed from step 1 back into the device.

Note: The ENS1200 should ONLY be powered via Ethernet cable connected to

the included PoE Injector.

Computer setup

1. After ensuring the EnGenius device is powered on and plugged in, ensure

that your computer is on.

2. For the next steps, refer to your operating system user manual.

3. Once your computer is on, ensure that your TCP/IP is set to ‘ON’ or

‘ENABLED’. In the control panel, double click network connections and then

double click on the connection of your Network Interface Card (NIC). Select

Internet Protocal (TCP/IP) and then click on the properties button.

4. If your PC is already on a computer network, ensure that you have set it to a

Static IP adress on the interface (or Ethernet card that will use the ENS1200).

Set it as 192.168.1.21 and set the Subnet Mask address as

255.255.255.0. Select ‘Use the following IP address’-radio button. Once the

computer has been prepared, proceed to setting up the ENS1200.

Summary of content (4 pages)

PAGE 1
ENS1200 Quick Installation Guide Package content Unpack the box and verify the content: - ENS1200 - PoE injector - Power adapter - Quick Start Guide - Wall mount screw set - 2* Pole mounting strap Minimum requirements - Broadband Internet Service (cable or DSL modem) - Internet browser (Internet Explorer, Safari, Firefox, Chrome) Connecting the ENS1200 1. Remove the rear bottom panel. 2.
PAGE 2
ENS1200 Quick Installation Guide ENS1200 setup 1. To configure the ENS1200, open a web browser (example: Microsoft Internet Explorer, Mozilla Firefox, Google Chrome, etc.) 2. In the adress bar of the web browser, enter: 192.168.1.1 (the default IP address of the ENS1200) and hit ENTER. 3. A login screen will appear. By default, the username of the ENS1200 is admin and the password is admin. Enter the current username and password of the ENS1200 and then click ‘Login’.
PAGE 3
ENS1200 ENS1200 Wall mounting A. Attach the location sticker to the desired location on the wall and use a 6mm drill bit to drill the two holes. Quick Installation Guide C. Align the ENS1200 over the keyhole mounting slots and insert both screw heads into each keyhole slot. Then slide the ENS1200 downward until it’s firmly hooked in place. B. Insert the screw anchors into the 6mm holes then insert the screws and tighten. EnGenius Europe | Veldzigt 28, 3454 PW De Meern, Netherlands | 0900-WIFIABC | www.
PAGE 4
ENS1200 Quick Installation Guide ENS1200 Pole mounting A. Use a flathead screwdriver to unfasten the screw on the pole mounting ring and thread it through the middle tab on the rear of the ENS1200. B. Mount the ENS1200 onto the pole by wrapping the ring around the pole and fastening the screw. EnGenius Europe | Veldzigt 28, 3454 PW De Meern, Netherlands | 0900-WIFIABC | www.wifiabc.com Disclaimer: Information may be subject to changes without prior notification. Follow us https://www.linkedin.