Installation Guide

ManualsBrandsEnviroLite ManualsCommercial Lighting2 ft. x 4 ft. 5000 Lumens Integrated LED White Honeycomb Backlit Recessed Panel Light 4000K

WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN

POWER AT FUSE OR CIRCUIT BREAKER BEFORE

INSTALLING OR SERVICING THE FIXTURE.

LED PANEL

INSTALLATION INSTRUCTIONS

MODEL PHC24BL50

QUESTIONS? CALL TOLL

FREE

1-855-573-6156

Please read carefully and save these instructions as

you may need them at a later date.

GENERAL: All electrical connections must be in accordance with local

and National Electrical Code (N.E.C.) standards. If you are unfamiliar

with proper electrical wiring connections obtain the services of a

qualified electrician.

Remove the fixture from the box and make sure that no parts are missing

by referencing the PARTS illustrations.

WARNING- RISK OF FIRE OR ELECTRIC SHOCK

• Do not alter, relocate, or remove wiring, lampholders, power supply,

or any other electrical component.

If not qualified, do not

attempt installation. Contact a

qualified electrician.

• Do not make or alter any open holes in an enclosure of wiring or

electrical components during kit installation.

• To prevent wiring damage or abrasion, do not expose wiring to

edges of sheet metal or other sharp objects.

____________________________

ASSEMBLY AND INSTALLATION

Fig. 1

Fig. 2

Fig. 3

1. Place the Panel in the ceiling (Fig 1)

2. From above the ceiling, secure the fixture to the T-Bar by bending the

built-in four T-bar clips (Fig 2).

3. If local code requires, tie a wire to at least two of the four T-bar clips

located near each corner of the fixture to a structural member of the

ceiling (Fig 2).

1. Remove the access plate located on back of the fixture (Fig 3).

Locate the black fixture wire, the white fixture wire and green ground

wire with connectors.

2. Remove one knockout in the access plate

3. Thread the power supply wires through the knockout hole in the

access plate.

4. Connect the black supply wire to the black fixture wire connector.

5. Connect the white supply wire to the white fixture wire connector.

6. Connect the supply ground wire to the fixture ground wire connector.

1. Remove the access plate located on the back of the fixture. Locate

the purple fixture wire and the pink fixture wires.

2. Remove one knockout in the access plate

3. Thread the 0-10V dimmer pink & purple wires through the knockout

hole in the access plate.

4. Connect the fixture pink wire to dimmer pink wire. Connect the fixture

purple wire to dimmer purple wire. Replace the access plate when

finished.

Securing the fixture

Connecting the wires

Connecting the dimming wires (optional)

Summary of content (6 pages)

PAGE 1
LED PANEL INSTALLATION INSTRUCTIONS MODEL PHC24BL50 Please read carefully and save these instructions as you may need them at a later date. Fig. 1 GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician. Remove the fixture from the box and make sure that no parts are missing by referencing the PARTS illustrations.
PAGE 2
________ DIMMING For an up-to-date list of compatible dimmers, look up item number at www.envirolite-LED.com. . ____________________________ FIVE-YEAR LIMITED WARRANTY Envirolite warrants this product to be free from defects in material and workmanship for five years from the original date of purchase by the consumer. This warranty is limited to the counter replacement at the time of purchase, with the original purchase receipt.
PAGE 3
INSTRUCCIONES PARA LA INSTALACIÓN PANEL DEL MODELO PHC24BL50 Lea cuidadosamente y guarde estas instrucciones ya que podría necesitarlas más adelante. ¿PREGUNTAS? LLAME GRATIS AL 1-855-573-6156 Fig. 1 GENERAL: Todas las conexiones eléctricas deben realizarse conforme a las normas locales y al Código Eléctrico Nacional (N.E.C. por sus siglas en inglés). Si no está familiarizado con las conexiones adecuadas de cableado eléctrico obtenga los servicios de un electricista calificado.
PAGE 4
_________________________________ REGULADOR DE INTENSIDAD DE LA LUZ Para una lista completa de atenuadores compatibles, por favor a el numero de articulo que en www.envirolite-LED.com. . . _________________________________ GARANTIA LIMITADA DE CINCO AÑOS Envirolite garantiza este producto contra defectos en sus materiales y mano de obra por un plazo de cinco años a partir de la fecha de compra.
PAGE 5
MODE D’INSTALLATION POUR GARNITURE DE PANNEAU DEL MODÈLE PHC24BL50 Veuillez lire ces instructions attentivement et les conserver pour pouvoir les consulter au besoin. DES QUESTIONS? APPELEZ SANS FRAIS AU 1-855-573-6156 Fig. 1 GÉNÉRALITÉS: Tous les raccordements doivent être effectués conformément aux exigences des règlements locaux et du code national de l’électricité (CNE).
PAGE 6
___________________________________ GRADATION DE L’INTENSITÉ LUMINEUSE Pour une liste complète des gradateurs compatibles, consultez le numéro article à www.envirolite-LED.com. ______________________________ GARANTIE LIMITÉE DE CINQ ANS Envirolite garantit ce produit contre tout défaut de matériaux ou de fabrication pour une période d’cinq ans à partir de la date d’achat initial par le client, à l’exception de la pile.