SERVICE MANUAL ROSCO A4 Monochrome Page Printer EPSON EPL-6200/EPL-6200L SEPG03002
Notice All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic, mechanical, photocopying, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.
PRECAUTIONS Precautionary notations throughout the text are categorized relative to 1)Personal injury and 2) damage to equipment. DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures preceded by DANGER Headings. WARNING Signals a precaution which, if ignored, could result in damage to equipment.
About This Manual This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. Manual Configuration This manual consists of six chapters and Appendix. CHAPTER 1.PRODUCT DESCRIPTIONS Provides a general overview and specifications of the product. CHAPTER 2.
Safety Precautions To prevent accidents during a maintenance procedure, strictly observe the Warnings and Cautions and never depart from the instructions given in this document. Do not do anything that is dangerous even if not specifically described in this manual. In work operations, always take great care to ensure safety in consideration of not only the precautions described below but also general safety precautions. Laser Safety This printer is digital equipment qualified as a Class 1 laser product.
Laser Safety and Caution Labels Warning labels and caution labels are affixed to this printer for accident prevention. C H E C K P O IN T In maintenance work, check that the labels are free from peeling and soiling. Laser safety label As shown below, a laser safety label is stuck on the rear panel of the printer beside the AC inlet. Laser caution label As shown below, a laser caution label is stuck on the inside of the printer.
Revision Status Revision Date of Issue A September 5, 2003 Description First release
EPSON EPL-6200/EPL-6200L Revision A Contents Chapter 1 Product Description 1.1 Outline ................................................................................................................. 13 1.1.1 Features....................................................................................................... 13 1.1.2 Differences between Models ...................................................................... 16 1.1.2.1 “EPL-6200” Differences from EPL-6100 .................................
EPSON EPL-6200/EPL-6200L 1.10.3 About the Moist Environment Mode Select ............................................. 1.11 Status Sheet ....................................................................................................... 1.12 Ambient Conditions........................................................................................... 1.13 Differences in Specifications between Intended Markets ................................. 1.13.1 Differences in Specifications ..........................
EPSON EPL-6200/EPL-6200L Revision A 3.2.15 EEPROM Error....................................................................................... 114 3.2.16 Engine Initialization Error ...................................................................... 115 3.2.17 Other Hardware Error ............................................................................. 115 3.2.18 Software Error ........................................................................................ 115 3.
EPSON EPL-6200/EPL-6200L 4.7 Duplex Unit (Option) ........................................................................................ 4.7.1 Right Cover............................................................................................... 4.7.2 Left Cover ................................................................................................. 4.7.3 Duplex Unit Control Board ...................................................................... 4.7.4 Duplex Unit Inversion Motor ........
1 CHAPTER PRODUCT DESCRIPTION
EPSON EPL-6200/EPL-6200L Revision A 1.1 Outline Toner life Table 1-2. Toner Life EPSON EPL-6200 and EPSON EPL-6200L are non-impact page printer with semiconductor laser and electrophotographic technology. 1.1.1 Features Model Initial EPL-6200 3000 pages EPL-6200L 1500 pages Replacement 3000 pages 6000 pages 3000 pages ENGINE FEATURES Photoconductor Unit A compact and lightweight A4 engine.
EPSON EPL-6200/EPL-6200L CONTROLLER FEATURES High-speed controller CPU : TMPR4955BFG 200 MHz (Same as for EPL-N2500) RAM : 8 MB fitted as standard RAM and Expandable up to 136 MB Max. Exclusive RAM DIMM for EPSON (Same as for EPL-6100) Equipped with one Type B interface slot (Level 3 supported) Two standard interfaces IEEE1284 parallel interface USB interface Real 1200dpi supported (Only in ESC/Page, PCL6, PostScript 3.
EPSON EPL-6200/EPL-6200L Revision A SOFTWARE FEATURE (ONLY WITH EPL-6200) OTHER FEATURE (ONLY WITH EPL-6200L) Printer status and printer environment are monitored by bidirectional EJL and Toner save image is made by Printer Driver. ESC/Page. Physical engine offset setting function (It is set by printer driver) The following modes and resolution are supported. Printer sharing (Printer driver’s function) Table 1-3.
EPSON EPL-6200/EPL-6200L Revision A 1.1.2 Differences between Models 1.1.2.2 “EPL-6200L” Differences from EPL-6100L Printing speed is 20 ppm (EPL-6100L: 16 ppm) 1.1.2.1 “EPL-6200” Differences from EPL-6100 CSIC with Developer Cartridge (toner cartridge) Table 1-5.
EPSON EPL-6200/EPL-6200L Revision A 1.1.3 Other (Only with EPL-6200L) 1.1.3.1 Restrictions on Use of EPL-6200L The printer itself cannot print the Status Sheet. When the printer is connected to a parallel interface, printing via devices such as a printer switch, LAN-Parallel converter, or USB-Parallel converter is not guaranteed. → Direct connection to a printer port of the host computer with an ECP supporting cable is premised. Using a converter for a USB connection is not guaranteed.
EPSON EPL-6200/EPL-6200L Revision A 1.2 Basic Specifications 1.2.2 Printer Basic Specifications Resolution: 1.2.1 Process Specifications Table 1-8.
EPSON EPL-6200/EPL-6200L Revision A Normal paper (including labels and transparencies) Thick paper Table 1-10. Continuous Printing Speed with Plain Paper (Unit: ppm or more) EPL-6200 Paper Size EPL-6200L Simplex Duplex Simplex 600 dpi 600 dpi 1200 dpi A4 20.0 LGL EPL-6200 Paper Size 600 dpi 1200 dpi 2-sheet circulation 1-sheet circulation 2-sheet circulation 10.0 10.4 13.5 5.2 6.7 20.0 16.0 8.0 - - - - 16.0 LT 20.0 10.0 10.4 13.5 5.2 6.7 20.0 B5 20.0 10.0 10.
EPSON EPL-6200/EPL-6200L Revision A Thick paper ppm control For thick paper printing, sheets of paper is fed at wider intervals (ppm Down) as described below to prevent temperature rise at both ends of the fuser unit. The ppm Down control will be started after a lapse of 100 seconds from the start of Thick Paper printing.
EPSON EPL-6200/EPL-6200L Revision A Paper Feed Reference Table 1-13. Paper Feed with “EPL-6200L” Centerline reference for each paper size and each paper feeder. Paper Source Paper Feed: 180 sheets Standard paper: FX-P Paper: A4 Table 1-12.
EPSON EPL-6200/EPL-6200L Revision A Available Paper Sizes, Paper Types, and Paper Orientation Table 1-14. Available Paper Sizes, Paper Types, and Paper Orientation Table 1-14. Available Paper Sizes, Paper Types, and Paper Orientation Dimensions Length x Width in mm (inches) MP Tray Paper Size Paper Manual Lower Duplex Paper Orientation Feed Cassette Unit *4 Tray *4 Tray EPL6200L EPL-6200 MP Tray Paper Manual Lower Duplex Paper Orientation Feed Cassette Unit *4 Tray *4 Tray 297.00 x 210.
EPSON EPL-6200/EPL-6200L Revision A Envelope Orientation Output Paper Capacity Table 1-16.
EPSON EPL-6200/EPL-6200L Revision A Dimensions and Weight Stand Alone Outline Dimensions and Weights Table 1-19. Stand Alone Outline Dimensions and Weights of “EPL-6200L” Stand Alone Outline Dimensions and Weights Width (mm) Depth (mm) Height (mm) Weight (kg) Output tray in storage position 385 279 261 6.0 Output tray and Paper Tray in use position 385 405 372 6.0 Table 1-17.
EPSON EPL-6200/EPL-6200L Revision A Consumables: Developer Cartridge (black toner) Photoconductor Unit (Drum Cartridge) NOTE: Noise Table 1-21. Noise Refer to “1.2.9 Consumable Components (p.32)”. During standby During printing Sleep mode 30.0dB(A) *1 54.0dB(A) Background noise Main Unit only Regular Replacement Parts Without taking into account replacement by the user, the lives of regular replacement parts are as follows: Note “*1”: The fan runs at a half speed.
EPSON EPL-6200/EPL-6200L Revision A 1.2.3 Paper Specification • Four-leaf printed postcard, postcards made for inkjet printing, or press sealed postcards • Iron print coated paper (for inkjet or laser printing) • Sheets deteriorate or discolor by heat of the Fuser Unit of approximately 200°C. 1.2.3.1 Paper Type Standard Paper RX-80 paper: A4 / XEROX 4024 DP 20lb: Letter paper Plain Paper 60 g/m2 ~ 90 g/m2 (16 lb ~ 24 lb) generally applied copy paper, regenerated paper 1.2.3.
EPSON EPL-6200/EPL-6200L Revision A 1.2.4 Reliability, Durability, Serviceability 1.2.3.3 Printable Area Available Printing Area: 1.2.4.1 Reliability 208.0mm × 348.0mm MPBF Guaranteed Printing Area: All area of the sheet except vertical and horizontal margins of 4 mm (See illustration below) 25,000 pages NOTE: MPBF means an average number of pages printed until the occurrence of a malfunction which either requires the replacement of parts or cannot be solved by the user.
EPSON EPL-6200/EPL-6200L Revision A Printing Start Position Accuracy Skew (With standard paper fed from Paper tray or Lower cassette) Table 1-26. Skew Table 1-25. Printing Start Position Accuracy Scanning Direction Simplex: A4 Duplex: A4 Simplex Duplex Main scanning direction |a-b| ±1.59 mm ±2.12 mm Reference point of Main scanning direction (c) ±2.0 mm ±3.0 mm Sub scanning direction |c-d| ±2.08 mm ±3.13 mm Reference point of Sub scanning direction (a) ±2.5 mm ±3.
EPSON EPL-6200/EPL-6200L Revision A 1.2.5 Operating Conditions (Including Consumables) Upper value: EPL-6200 (Lower value): EPL-6200L Ambient Temperature and Humidity Conditions Table 1-29. Ambient Temperature and Humidity Conditions Temperature (°C) Humidity (%RH) Printer is under operation 10 ∼ 35 15 ∼ 85 Printer is stopped 0 ∼ 35 10 ∼ 85 Others No condensation Barometric Pressure 76.0 to 101.
EPSON EPL-6200/EPL-6200L Revision A 1.2.6 Storage and Transport of the Printer Main Unit and Optional Products (Consumables Packaged) Fast Transient / Bursts (AC Line Noise) IEC 61000-4-4 compliance Temperature and Humidity Conditions Voltage 1 k: no malfunction occurs such as defective image quality. 2 kV: no damage to parts allowed. Table 1-30.
EPSON EPL-6200/EPL-6200L Revision A EMC 1.2.8 Compliance with Standards and Regulations Safety Standards Table 1-33. Model Name Table 1-31. Safety Standards Model Name 100V 100V Applicable Standards 110V-120V IEC60950 (1998) compliant 110V-120V UL60950 3rd (2000) CSA-C22.2 No.
EPSON EPL-6200/EPL-6200L Revision A 1.2.9 Consumable Components 1.2.9.2 Packing Storage and Transport Environments Temperature and Humidity Conditions 1.2.9.1 Specifications Table 1-35. Temperature and Humidity Conditions Table 1-34.
EPSON EPL-6200/EPL-6200L Revision A 1.3 External Appearance and Parts Name 1.3.1 Overall Dimensions of EPL-6200 Figure 1-6 (p.33) to Figure 1-9 (p.33) show the overall dimensions of EPL-6200. Figure 1-8. Right Side View with Lower Cassette installed Figure 1-6. Front View of EPL-6200 Figure 1-7. Right Side View with Output Tray in Use Product Description External Appearance and Parts Name Figure 1-9.
EPSON EPL-6200/EPL-6200L Revision A 1.3.2 Overall Dimensions of EPL-6200L Figure 1.3.1 (p.33) to Figure 1-11 (p.34) show the overall dimensions of EPL-6200L. Figure 1-10. Right Side View with MP Tray and Output Tray in Use Figure 1-11.
EPSON EPL-6200/EPL-6200L Revision A 1.3.3 Names of Parts of EPL-6200 Table 1-36.
EPSON EPL-6200/EPL-6200L Revision A Figure 1-15. EPL-6200 Names of Parts 4 Figure 1-14.
EPSON EPL-6200/EPL-6200L Revision A 1.3.4 Names of Parts of EPL-6200L Table 1-37. Names of Parts Symbol Name 1 Output Tray 2 LED 3 Front Cover 4 Paper Tray 5 Power Switch 6 Parallel I/F Connector 7 USB I/F Connector 8 AC Inlet 9 Output Cover Figure 1-16. EPL-6200L Names of Parts 1 Product Description Figure 1-17.
EPSON EPL-6200/EPL-6200L Revision A 1.4 Controller Specification EPL-6200L CPU 1.4.
EPSON EPL-6200/EPL-6200L Revision A 1.4.2 External I/F Specifications 1.4.2.1 Parallel Interface Specifications EPL-6200/EPL-6200L is equipped with the external host interfaces as listed below: Table 1-39. Parallel Interface Specifications Table 1-38. External Host Interfaces Standard Optional IEEE1284 parallel interface USB interface (USB Revision 1.
EPSON EPL-6200/EPL-6200L Revision A 1.4.2.2 USB Interface 1.4.2.3 Type B Interface (Not Available with EPL-6200L) Supports Windows USB PnP. EPL-6200 is equipped with one Type-B option I/F slot as standard. Supports the 18-digit USB ID as follows: Main System Type: MTP1200dpi, PW10200dt1200dpi, PRG(****)rev, AP500ma, SPD0fast, D4 **P++YYMMDDhhmmssR **: A number of 00 to 99. Acquired for each model. “24” for EPL-6200. “23” for EPL-6200L. P: Identifier. Always “P” for page printers.
EPSON EPL-6200/EPL-6200L Revision A 1.5 Control Panel (EPL-6200) 1.5.2 List of Settings 1.5.1 External Appearance and Names of Parts This section describes setting items for EPL-6200. The setting items are described in groups for each tab screen of the printer driver. Values shown in bold and underlined characters are the factory default setting values. Basic Settings Table 1-42.
EPSON EPL-6200/EPL-6200L Revision A Layout Printer Settings Table 1-43. Setting Items (Layout) Item Dialog *1 Table 1-46.
EPSON EPL-6200/EPL-6200L Revision A Extended Settings Table 1-47. Extended Settings Item C A U T IO N Setting Value Graphic Mode *1 Do not disclose any hidden functions to users. High Quality (Printer), High Quality (PC) Print TrueType fonts as bitmap, Print TrueType fonts with substitution TrueType Font Uses the settings specified on the printer, Uses the settings specified on the driver Front Top Panel Settings Offset Front Left -30 ~ 0 ~ +30 mm (in 0.
EPSON EPL-6200/EPL-6200L Revision A 1.5.3 Printer Messages A list of printer messages with EPL-6200 is shown below. Table 1-48.
EPSON EPL-6200/EPL-6200L Revision A Table 1-48.
EPSON EPL-6200/EPL-6200L Revision A 1.5.4 Special Operation (EPL-6200) With EPL-6200, the functions described below are activated by holding the specified switches down when turning the printer on. C A U T IO N The functions other than Hexadecimal Dump and Photoconductor Life Reset must not be disclosed to the user.
EPSON EPL-6200/EPL-6200L Revision A 1.6 Control Panel (EPL-6200L) Meaning of LED Flashing on EPL-6200L Table 1-51. Meaning of LED Flashing 1.6.1 External Appearance and Names of Parts Ready LED Error LED Supplement Off Off - Power off On Off - Ready to print (It include warning status) Blink 1 Off - Blink 3 Off - Off Blink 1 2 1 Blink 1 Blink 1 Blink 1 Blink 1 Green and red blink alternately Green and red blink simultaneously 1. Green: On, Red: On 2. Green: Off, Red: Off 3.
EPSON EPL-6200/EPL-6200L Revision A Setting Items Requiring Administration by the Printer for each Printing or state 1.6.2 Printer Setting Items change A list of setting items for this printer is shown below. Table 1-54. Function Setting (3) Setting Items for which the Printer Stores the Changed Settings Administrative Table 1-52.
EPSON EPL-6200/EPL-6200L Revision A 1.6.3 Status Table 1-55. Printer Status (continued) Status description 1.6.3.1 Status List Items of printer status generated in this printer are listed below: Table 1-55.
EPSON EPL-6200/EPL-6200L Revision A Processing 1.6.3.3 Details of Error Status and Processing The printing will start automatically after completion of the current job. Processing Job Description The printer is processing a print job Sleep mode Description The printer is in sleep mode. Processing The printer becomes ready to print after receiving printing data. Ready Description The printer is ready to print (normal status).
EPSON EPL-6200/EPL-6200L Revision A Feed Jam (Paper Out) Description NonGenuineToner Cart Description No paper has been fed even though printer has started printing action. The error is cleared when there is no longer any paper jam detected after opening and closing the front cover. After error recovery, data for one page retained in the printer memory are recovered if it is possible, and if the data cannot be recovered, the printer returns a resending request.
EPSON EPL-6200/EPL-6200L Revision A Front Cover Open Description Invalid Size Description Font printer cover is open. This error is cleared when the cover is not detected to be open any longer. Remedy When the cover is closed, the error is cleared, and the pop-up display of the EPSON Status Monitor disappears accordingly. Exit Cover Open Description Remedy Output Cover is open. This error is cleared when the cover is not detected to be open any longer.
EPSON EPL-6200/EPL-6200L Revision A “Near Buffer Full”. The Continue command of the ESCPAGES-02 protocol releases the error, and printing resumes from the next page. When “Auto Continue = ON”, the printer displays the “Print Failure” warning instead of this error, and resumes printing the next page.
EPSON EPL-6200/EPL-6200L Revision A When you replace the Developer Cartridge (toner cartridge), the pop-up message of the EPSON Status Monitor disappears. (The toner counter reset can be executed even if you do not replace the Developer Cartridge.) Worn Photoconductor Description 1.6.4 Special Operation (EPL-6200L) This section describes the special operation functions of EPL-6200L. C A U T IO N This function, a hidden function, must not be opened to users. Photoconductor life is 5% or less.
EPSON EPL-6200/EPL-6200L Revision A HOW TO INITIALIZE EEPROM 1.6.4.2 Printer Adjustment (Hidden Function) 1. Open the “Optional Settings” of the printer driver property. For the following setting items for which the printer stores the settings, you can change the setting by the following procedures: 2. While pressing the [ALT] + [CTRL] + [SHIFT] + “W” keys together on the keyboard of the personal computer, click any point in the blank area on the screen. Humidity: 3.
EPSON EPL-6200/EPL-6200L Revision A 3. On the screen of the printer adjustment window (hidden window), change the setting value for the appropriate item. 4. After changing the setting value, click the [Execute] button of the printer driver to finalize the setting. Figure 1-23.
EPSON EPL-6200/EPL-6200L Revision A 1.7 RAM Expansion 1.8 System Requirements (Only for EPL-6200L) When EPL-6200 runs out of memory, the Memory LED flashes or lights up. In this case, you have to mount expanded RAM (RAM DIMM). The minimum system configuration and recommended system configuration when using EPL-6200L are shown in Figure 1-56 (p.57) and Figure 1-57 (p.57). This problem may be solved by taking appropriate ones of the following measures: Table 1-56.
EPSON EPL-6200/EPL-6200L Revision A 1.9 Paper Feed Specifications (Only for EPL-6200L) 1.9.1 Paper Size 1.9.2 Paper Feed Specifications The following three types of information related to paper sizes are available. User setting size: Paper sizes that the user specifies on the printer driver. A4, A5, B5, LT, HLT, LGL, GLT, GLG, EXE, F4, MON, C10, DL, C5, C6, IB5, User defined size Printer paper size: Paper sizes for the MP Tray that the printer recognizes is stored in EEPROM.
EPSON EPL-6200/EPL-6200L Revision A 1.9.3 Case List The table below shows a case list of paper feed specifications for each paper size. Table 1-59.
EPSON EPL-6200/EPL-6200L Revision A 1.10 Notes on Operation 1.10.3 About the Moist Environment Mode Select 1.10.1 Power Off (EPL-6200) This is a switch that operates to lower the print density in a high humidity environment. Ordinarily it does not operate. EPL-6200 incorporates an internal non-volatile memory (EEPROM). If the power to the printer is turned off during the process of writing in non-volatile memory, the successful writing in the non-volatile memory cannot be guaranteed.
EPSON EPL-6200/EPL-6200L Revision A 1.11 Status Sheet A sample of the Status Sheet is shown at right. The following information is printed at bottom left in the order of 1) to 8): 1). IA followed by firmware version shown in the DDYM format For M (month), “A” represents October, “B” November and “C” December 2). Negotiation result of IEEE1284 e: ECP, n: Nibble, or none: Compatibility or not connected 3). Device type of code ROM *: Flash or none: Mask 4).
EPSON EPL-6200/EPL-6200L Revision A Notes on the status sheet (a sample) for EPL-6200 are as follows: Note “*1”: Printed only when the relevant optional unit has been installed. “*2”: “Needed Soon” will be shown when the amount of toner remaining is supposed to permit printing for not more than 300 sheets. “*3”: “Needed Soon” will be shown when photoconductor life is 5% or less.
EPSON EPL-6200/EPL-6200L Revision A A sample of the Status Sheet is shown at right. The following information is printed at bottom left. NOTE: A space is put in each item. IAXXXX Controller firmware date. XXXX=ddym About the m (month), they are shown as below. Oct. is A, Nov. is B and Dec. is C. JXXXXX Jam counter (the number of digits is five) ICX Y X: Counter of changing of Developer Cartridge (toner cartridge).
EPSON EPL-6200/EPL-6200L Revision A 1.12 Ambient Conditions ENGINE STATUS SHEET (EPL-6200) Printing Procedure: The ambient conditions to ensure the performance of EPL-6200/EPL-6200L are as follows: 1. Open the printer driver on the personal computer. 2. Open the “Optional Settings” page. 3. Click the “Extended Settings” button while holding down [ALT] + [CTRL] + [Z] keys. C H E C K P O IN T This function, a hidden function, must not be opened to users.
EPSON EPL-6200/EPL-6200L Revision A 1.13 Differences in Specifications between Intended Markets 1.13.1 Differences in Specifications Table 1-60.
EPSON EPL-6200/EPL-6200L Revision A 1.14 Notes on Installation of Optional Units 1.13.2 Jumper Setting C533MAIN (for EPL-6200) is equipped with two resistance jumpers. Resistance Jumper R1101 J spec setting The Duplex Unit cannot be installed without the Lower Cassette Unit installed.
2 CHAPTER OPERATING PRINCIPLES
EPSON EPL-6200/EPL-6200L Revision A 2.1 Overview EPL-6200 and EPL-6200L are almost the same in operating principles. However, do not forget that there are some differences in mechanisms between EPL-6200 and EPL6200L. 2.1.1 EPL-6200 Major Components Table 2-1. EPL-6200 Major Components No.
EPSON EPL-6200/EPL-6200L Revision A 2.1.2 EPL-6200L Major Components Table 2-2. EPL-6200L Major Components No. Major Components 1 Print Head Unit 2 Paper Exit Roller 3 Fuser Unit 4 Transfer Section 5 MP tray 6 Developer Cartridge (toner cartridge) 7 Photoconductor Unit (Drum Cartridge) Figure 2-2.
EPSON EPL-6200/EPL-6200L Revision A 2.1.3 Paper Path Output Tray EPL-6200 Duplex Unit (Option) Paper feed is carried out through two ways from the MP Tray (250 sheets) and Manual Feed Tray (1 sheet). An optional lower cassette unit (500 sheets) can be installed so that three paper feed methods are available. Paper fed by the paper feed roller is carried through transfer roller → fusing roller → paper exit roller and ejected to the Face-down Output Tray.
EPSON EPL-6200/EPL-6200L Revision A 2.1.4 Electrical Parts Printer Body Table 2-3. Electrical Parts Symbol Name M1 Main Motor M2 Cooling Fan Motor H1 Fusing Roller Heater Lamp TH1 Thermistor TS1 Thermostat PH Print Head Unit S1 Paper Feed Sensor S2 Front Cover Switch PE1 Paper Tray Empty Sensor PS3 Paper Eject Sensor SL-1 Paper Feed Solenoid PU-1 Power Supply Unit HV-1 C533/C534 Main High Voltage Unit Mechanical Control Board Figure 2-4.
EPSON EPL-6200/EPL-6200L Revision A 2.1.5 Operation Sequence Printing Start Sequence Printing End Sequence Figure 2-6. Printing End Sequence Figure 2-5.
EPSON EPL-6200/EPL-6200L Revision A 2.1.6 Various Sensors Table 2-4. Various Sensors Unit Printer Body Paper Tray Standard (Printer Body) Developer Cartridge (toner cartridge) Photoconductor Unit (Drum Cartridge) Optional Operating Principles Lower Cassette Unit Detected Matter EPL-6200 EPL-6200L Detecting Method Paper jam { { Actuator + photo switch p.83 Automatic detection by sensor p.
EPSON EPL-6200/EPL-6200L Revision A 2.2 Description of Mechanisms Semi-conductor Laser SOS (Start of Scan) Sensor 2.2.1 Print Head (PH) G1 Lens G2 Lens 2.2.1.1 Entire Constitution 1st Mirror Scanning with the laser beam coming out of the Print Head is performed by the polygon motor. (See “Figure 2-7”) 2.2.1.2 Exposure Process The laser beam from the print head creates an electrostatic latent image on the OPC drum surface.
EPSON EPL-6200/EPL-6200L Revision A 2.2.1.3 Laser Emission Timing When the Ready signal is detected upon passage of a certain period of time after issue of the printing start signal, the Laser ON signal is output from the Mechanical Control Board. (See “Figure 2-9”) Polygon Mirror SOS Mirror Upon issue of the Laser ON signal, the laser beam is forcibly emitted. The laser beam, via the polygon mirror → G1 lens → SOS mirror, strikes the SOS sensor to issue the SOS signal.
EPSON EPL-6200/EPL-6200L Revision A 2.2.1.5 Cooling inside the Printer The Cooling Fan Motor discharges the heat emitted by the Print Head Unit to the outside of the printer, thus preventing temperature rise of the Print Head Unit. Figure 2-11.
EPSON EPL-6200/EPL-6200L Revision A 2.2.2 Charging Process Before laser exposure, static electricity is given to the OPC drum (Organic Photoconductor) to charge it. Photoconductor Unit The surface of the OPC drum is charged by the rotating brush (charging brush) and Paper Powder Cleaner Drum Cover pre-charging film.
EPSON EPL-6200/EPL-6200L Revision A 2.2.3 Development Process (Imaging Cartridge) 2nd toner blade Imaging Cartridge 2.2.3.1 OVERVIEW OPC Drum The Developer Cartridge and development section are constructed as described below: This printer employs one-component FMT (Fine Micro Toning) development method. Toner in the Developer Cartridge (toner cartridge) is sent into the toner sending roller area by the toner agitation blade.
EPSON EPL-6200/EPL-6200L Revision A 2.2.3.2 OPC Drum Electric charge retaining layer An OPC (Organic Photo Conductor) is used. Carrier generation layer This photoconductor is of a laminate type consisting of a carrier generation layer and Aluminum base an electric charge retaining layer applied onto an aluminum base (cylinder).
EPSON EPL-6200/EPL-6200L Revision A 2.2.3.3 Development Process OPC Drum Toner in the Developer Cartridge (toner cartridge) is sent into the toner sending 2nd Toner Blade roller area by the toner agitation blade. The toner sending roller transports the toner to the development roller side. The toner which has been transported onto the development roller forms a uniform 1st Toner Blade Toner Transport Roller thin layer on the development roller by the operation of the 1st toner blade.
EPSON EPL-6200/EPL-6200L Revision A 2.2.3.4 Detection Of Developer Cartridge (toner cartridge) Installation Detection (Presence Detection): Installation of the Imaging Cartridge is detected in such a way that its presence/ absence is electrically detected at power off and on or opening and closing of the front cover by the IC chip (CSIC) incorporated in the Developer Cartridge (toner cartridge).
EPSON EPL-6200/EPL-6200L Revision A 2.2.4 Transfer Process Overview The image created on the OPC drum in the development process is transferred OPC Drum to the paper. Transfer is performed by the roller transfer method using the transfer roller. By the roller transfer method, ozone is generated rarely and the transferred image is little dislocated since the paper passes between the drum and the transfer roller all through during printing.
EPSON EPL-6200/EPL-6200L Revision A 2.2.5 Fusing Process Actuator 2.2.5.1 Overview In this process, the toner transferred to the paper in the transfer process is fused to the paper. Fusing Separation Claw Thermostat (TS1) For fusing, this printer uses the heat roller fusing system. The sheet with toner on passes between the heat roller, which is heated up by the fusing heater lamp, and the pressure roller.
EPSON EPL-6200/EPL-6200L Revision A TEMPERATURE CONTROL MODE During printing, the fuser temperature is adjusted along the passage of time counted from completion of warming up. Mode 1: Temperature control mode 1 continues for five minutes. However, the temperature adjustment mode 1 that was interrupted once is resumed with the timer counting from the count just before interruption, if the thermistor temperature is 50°C or higher.
EPSON EPL-6200/EPL-6200L Revision A 2.2.6 Paper Feed Mechanism 2.2.6.1 MP (Multiple Purpose Paper) Tray Push-down Cam Paper Feed Roller PAPER FEED OPERATION When the paper feed solenoid is turned ON, the driving power from the main Paper Feed Sensor (S1) motor is transmitted to the paper feed roller via the paper feed clutch, and the paper feed roller rotates. At the same time, the push-down cam rotates, and it lifts the tray.
EPSON EPL-6200/EPL-6200L Revision A MP TRAY EMPTY SENSOR The MP Tray Empty Sensor, mounted at the top of the MP Tray, detects paper in the MP Tray. (See “Figure 2-15”) When there is paper, the actuator is lifted so that the light to the sensor is intercepted. When the paper has been used up, the actuator falls into the hole in the tray so that the light to the sensor is transmitted.
EPSON EPL-6200/EPL-6200L Revision A 2.2.7 Lower Cassette (Option for EPL-6200) PWB-A CAS This section describes the mechanism of the optional lower cassette unit for EPL-6200. 2.2.7.1 Locations of Electrical Parts See Figure 2-24 at right and Table 2-7 below for locations of electrical parts. SW1 Table 2-7. Electrical Parts Symbol Names of Parts SW1 Cassette Type Sensor Switch PWB-A CAS 2nd Tray Control Board SL-2 2nd Tray Paper Feed Solenoid 2.2.7.
EPSON EPL-6200/EPL-6200L Revision A 2.2.7.3 Paper Cassette Empty Sensor The Paper Cassette Empty sensor is mounted on the control board in the Lower Cassette and it detects “paper cassette empty”. (See “Figure 2-26”) Paper Cassette Empty Sensor When there is paper, the actuator is lifted so that the light to the sensor is intercepted. When the cassette is empty of paper, the actuator falls into the hole in the paper lifting plate so that the light to the sensor is transmitted. 2.2.7.
EPSON EPL-6200/EPL-6200L Revision A 2.2.8 Paper Eject Process 2.2.8.1 Paper Eject Mechanism Output Tray Transports paper from the fuser area to the Paper Eject Roller. Paper Eject Roll Face-down Eject Paper Eject Roller Figure 2-28.
EPSON EPL-6200/EPL-6200L Revision A 2.2.9 Duplex Unit (option) 2.2.9.1 Locations of Electrical Parts Table 2-9.
EPSON EPL-6200/EPL-6200L Revision A 2.2.9.2 Driving of Duplex Unit The Duplex Unit is driven as follows: the paper after printing on one side is fed into the Duplex Unit Inversion Motor (M5) Output Tray once and when the tail end of the paper has left the guide behind the paper eject roller, the paper eject roller starts rotating to transport the paper into the Duplex Unit. (See “Figure 2-30”) The paper is transported into the printer body by the duplex unit transport motor.
EPSON EPL-6200/EPL-6200L Revision A 2.2.9.3 Paper Feeding System 1-SHEET CIRCULATION DUPLEX PRINTING 1. A sheet of paper is loaded and the image of the 2nd page is printed. 2. The sheet is sent to the paper eject area once, and then sent backward. 3. The sheet is transported into the Duplex Unit and fed into the printer body again without being stopped. 4. The image of the 1st page is printed on the sheet refed from the Duplex Unit. 5. The sheet of paper is ejected. 6.
EPSON EPL-6200/EPL-6200L Revision A 2-SHEET CIRCULATION DUPLEX PRINTING 1. The 1st sheet of paper is loaded and the image of the 2nd page is printed. 2. The sheet is sent to the paper eject area once, and then sent backward. 3. At the same time, the 2nd sheet of paper is loaded. 4. The image of the 4th page is printed on the 2nd sheet of paper. 5. The 1st sheet is transported into the Duplex Unit and fed into the printer body again without being stopped. 6.
EPSON EPL-6200/EPL-6200L Revision A 2.3 Operating Principles of Electric Circuitry 2.3.1 Operation Overview of the Main Control Circuit Board The main controller of EPL-6200 is a full-set controller which controls various printer modes and all the necessary processing up to video data generation. The main controller of EPL-6200L (host-based printer), however, is a simplified controller which only transfers the video data generated on the printer driver side to the engine side.
EPSON EPL-6200/EPL-6200L Revision A COMPARISON OF EPL-6200 WITH EPL-6100 Table 2-10. Comparison of EPL-6200 with EPL-6100 Device EPL-6100 EPL-6200 CPU TMPR4955AF-200 TMPR4955BFG-200 ASIC DLC: E05B96BA Memory, I/O integrated controller, USB ← Onboard MASK ROM None ← Standard ROM-DIMM 1 slot. +3.3V DIMM. IPL, Code, Font, SDRAM 1 slot. +3.3V DIMM.
EPSON EPL-6200/EPL-6200L Revision A Table 2-10. Comparison of EPL-6200 with EPL-6100 (continued) Device Expandability EPL-6100 EPL-6200 CPU ES, initial MP: EPROM Steady MP: Mask ← ROM Expansion by ROM-DIMM 90-pin. 1 slot None SDRAM Expansion by RAM-DIMM (Newly employed) 90-pin. 1 slot ← Type B 1ch: Normal orientation 1ch Reverse None For Mechanical Controller CPU. Provided (WS), Not provided (ES, MP) 200MHz ← IC socket CPU (inside) 66.67MHz SSCG-L ← Video 38.
EPSON EPL-6200/EPL-6200L Revision A MAJOR ELEMENTS Table 2-11. Major Elements Name CPU/Clock Location Remarks IC100 TMPR4955BFG-200 / 200MHz ASIC DLC: E05B96BA IC101 Memory control and I/O control integrated ASIC ROM DIMM Standard ROM DIMM CN300 IPL, code, font, PS, SDRAM onboard SDRAM Mounted on ROM DIMM. 8MB SDRAM DIMM CN200 For printer memory expansion (1 slot) 90-pin for exclusive use.
EPSON EPL-6200/EPL-6200L Revision A 2.3.1.2 Main Control Circuit Board (C533Main) for EPL-6200L EPL-6200L employs a newly developed controller for ESC/PageS Printing System. PRINCIPAL FEATURES All the functions, including those of the CPU, are incorporated in one ASIC (called “SLC2”). As the CPU core, C33 core made by EPSON is employed. The algorithm of the extension circuit is BitRepeat3.
3 CHAPTER TROUBLESHOOTING
EPSON EPL-6200/EPL-6200L Revision A 3.1 Overview Broken line arrow: Refer to depending on the result of diagnosis START With this printer, almost all troubles can be coped with by using “EPSON Status Monitor 3” installed on the host personal computer. 3.1.3 Preliminary Checks (p.101) Once an error occurs, the “EPSON Status Monitor 3” will appear as a pop-up window on the screen of the host PC. It will show details of how to cope with the trouble.
EPSON EPL-6200/EPL-6200L Revision A 3.1.3 Preliminary Checks 3.1.4 Notes on Troubleshooting Before starting troubleshooting, be sure to verify that the following conditions are all met: The troubleshooting method described here assumes there is no malfunction in the printer controller (Main Board). If you can not fix a problem even by following the troubleshooting procedure, you are advised to replace the printer controller with a normal one and then follow the same procedure.
EPSON EPL-6200/EPL-6200L Revision A 3.1.6 Printer Messages (EPL-6200) 3.1.6.1 Service Call Error The state of EPL-6200 is indicated in the following four types and all the indications are expressed by the LEDs on the control panel. When there is any error display, such as a service call error, print an error sheet to identify the content of error first, and then recover or repair the printer. Status: NOTE 1: For a list of printer messages, refer to “1.5.3 Printer Messages (p.44)”.
EPSON EPL-6200/EPL-6200L Revision A Engine Errors Table 3-1 below shows the engine-related service call errors in EPL-6200 Table 3-1. Service Call Error (Engine-Related) Error Code Eggg Explanation Paper LED 001 Fuser warming up problem z 003 Fan problem z 004 Polygon Motor Error 005 Laser problem 006 High voltage circuit problem 007 Fuser low temperature problem 008 Fuser high temperature problem 014 Engine Communication Error Toner LED Error LED Refer to z p.
EPSON EPL-6200/EPL-6200L Revision A Controller Errors Table 3-2 below shows a list of controller-related service call errors in EPL-6200. Table 3-2.
EPSON EPL-6200/EPL-6200L Revision A Table 3-2. Service Call Error (Controller-Related) (continued) Error Code C ffff Explanation Paper LED Toner LED Memory LED Ready LED Error LED z z z z z z z z z z z z z Standard RAM Error (No RAM at all, etc.) 1001 Standard RAM Error (Not enough for minimum stack, etc.) 1002 Standard RAM Error (Not enough for standard size, etc.
EPSON EPL-6200/EPL-6200L Revision A 3.1.7 Printer Messages (EPL-6200L) EPL-6200L is not equipped with an LCD. Once an error occurs, the “EPSON Status Monitor 3” will appear as a pop-up window on the screen of the host PC, showing the trouble. Figure 3-2. EPSON Status Monitor !3 (At occurrence of service call error) Engine Errors Table 3-3. Engine Errors Explanation Status code Refer to Fuser warming up problem 6001 p.107 Fan problem 6003 p.108 Polygon Motor Error 6004 p.
EPSON EPL-6200/EPL-6200L Revision A 3.2 Troubleshooting When There is Error Display This section describes troubleshooting for errors indicated by error display. After identifying the error item, refer to the appropriate page for troubleshooting. This section also describes troubleshooting for faulty operation of the printer. C H E C K P O IN T Refer to “Flowchart 3-1.Procedure for Troubleshooting (p.100)” first and then follow the troubleshooting procedures described in Table 3-4 to Table 3-18.
EPSON EPL-6200/EPL-6200L Revision A 3.2.2 Fan problem 3.2.3 Polygon Motor Error The following condition is handled as a fan problem: During operation of the Cooling Fan Motor, the lock signal (H or L) has been Any of the following conditions is handled as an polygon motor error: The lock signal was not detected within the predetermined period of time maintained for more than the predetermined period of time. counted from one second after start of the polygon motor.
EPSON EPL-6200/EPL-6200L Revision A 3.2.4 Laser problem 3.2.5 High voltage circuit problem Any of the following conditions is handled as a laser problem: When the laser output exceeded the upper limit. The laser output dropped below the lower limit. Any of the following conditions is handled as a high voltage circuit problem: The charging monitor voltage (HVC_MON) signal was detected to be out of the predetermined limits after passage of the predetermined period of time from power on.
EPSON EPL-6200/EPL-6200L Revision A 3.2.6 Fuser high temperature problem 3.2.7 CPU Error The following condition is handled as a fuser high temperature problem: During temperature control, the thermistor detected temperature was kept above 235°C over the predetermined period of time. Table 3-10. Troubleshooting for “CPU Error” Step Table 3-9.
EPSON EPL-6200/EPL-6200L Revision A 3.2.9 Fuser low temperature problem Table 3-12. Troubleshooting for “Fuser low temperature problem” (continued) The following condition is handled as a fuser low temperature problem: During temperature control, the thermistor detected temperature was kept Step below the preset temperature over the predetermined period of time continuously.
EPSON EPL-6200/EPL-6200L Revision A 3.2.10 Standard RAM Error 3.2.11 RAM Error (Slot 0) This error relates to the standard RAM memory mounted on the board assy. This error relates to expanded RAM. (EPL-6200 only) Table 3-13. Troubleshooting for “Standard RAM Error” Step 1 Action and Question Yes Table 3-14. Troubleshooting for “RAM Error” No Step No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Main Board Assy (C533/C534 Main) (p.
EPSON EPL-6200/EPL-6200L Revision A 3.2.12 ROM Checksum Error (Font) 3.2.13 ROM Checksum Error (Program) This error is a standard font ROM fault. This error is a built-in program ROM fault. Table 3-15. Troubleshooting for “ROM Checksum Error (Font)” Step 1 Action and Question Yes Table 3-16. Troubleshooting for “ROM Checksum Error (Program)” No Step No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Main Board Assy (C533/C534 Main) (p.
EPSON EPL-6200/EPL-6200L Revision A 3.2.14 Option ROM Error 3.2.15 EEPROM Error This error is an optional ROM fault. This error is an EEPROM fault. Table 3-17. Troubleshooting for “Option ROM Error” Step 1 Action and Question Yes Table 3-18. Troubleshooting for “EEPROM Error” No Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Main Board Assy (C533/C534 Main) (p.
EPSON EPL-6200/EPL-6200L Revision A 3.2.16 Engine Initialization Error 3.2.18 Software Error Table 3-19. Troubleshooting for “Engine Initialization Error” Step Action and Question Yes Table 3-21. Troubleshooting for “Software Error” No Step Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Main Board Assy (C533/C534 Main) (p.146) 1 Main Board Assy. 1. Replace the Main Board Assy. ♦Does the error still occur? Go to “3.4.2 Electrical Noise” (p.
EPSON EPL-6200/EPL-6200L Revision A 3.3 Troubleshooting for Paper Jam 3.3.2 Locations of Paper Jam Detection Sensors Eject Sensor (PS3) 3.3.1 Initial Checking Duplex Unit Upper Transport Sensor (PC4) If any paper jam has occurred, check the initial check items as listed below first. Table 3-22. Initial Check Items Check Item Remedy Is a specified type of paper used? Replace the paper. Is paper curled, wrinkled, or wet? Replace the paper. Tell the customer how to store paper.
EPSON EPL-6200/EPL-6200L Revision A 3.3.3 Jam Detection Timing / Action to be Taken 3.3.3.1 Paper Feed Area Jam / Paper Transport Area Jam 3.3.3.2 Fuser Area Jam / Paper Eject Area Jam Detection Timing Table 3-24. Detection Timing Category Table 3-23. Paper Feed Area Jam / Paper Transport Area Jam Category Explanation After start of paper feeding, the Paper Feed Sensor turned ON Jam detection in paper feed earlier than the passage of the predetermined time.
EPSON EPL-6200/EPL-6200L Revision A 3.3.3.3 Transport Area Jam in Duplex Unit (Option) 3.3.3.4 Paper Re-feed Area Jam in Duplex Unit (Option) Detection Timing Detection Timing Table 3-25. Transport Area Jam in Duplex Unit (Option) Category Transport component jam Explanation Category The Duplex Unit Upper Transport Sensor did not turn ON even after the passage of the predetermined period of time from interception of the light to the Paper Eject Sensor.
EPSON EPL-6200/EPL-6200L Revision A 3.4 Troubleshooting for Abnormal Operations 3.4.1 Power Cannot be Turned ON Table 3-27. Troubleshooting for Impossible Power Turning On Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Main Board Assy (C533/C534 Main) (p.146) • Power Supply Unit (PU1) (p.151) 1 Connection of power cord Check to see if the power cord is connected to the wall socket and the printer body properly.
EPSON EPL-6200/EPL-6200L Revision A 3.4.2 Electrical Noise Table 3-28. Troubleshooting for “Electrical Noise” (continued) Step Table 3-28. Troubleshooting for “Electrical Noise” Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Main Board Assy (C533/C534 Main) (p.146) • Power Supply Unit (PU1) (p.151) • Fuser Unit (p.152) • High Voltage Unit (HV1) (p.151) • Photoconductor Unit (p.135) • Developer Cartridge (p.
EPSON EPL-6200/EPL-6200L Revision A 3.5 Troubleshooting for Electrical Parts 3.5.3 Switches Table 3-30. Troubleshooting for Switches 3.5.1 Checking Method for Electrical Parts Step At occurrence of a paper jam or any other trouble, you can check the relevant electrical parts for their normality by the method as described below: 1 Check Item Does the input signal (NO) to Control Board turn L→H when the switch is turned on? Solution Yes: Replace the Control Board No : Replace the switch 3.5.
EPSON EPL-6200/EPL-6200L Revision A 3.5.5 Motors Table 3-34. Troubleshooting for Motors 3 Step Table 3-32.
EPSON EPL-6200/EPL-6200L Revision A 3.6 Troubleshooting for Print Quality Problems If any print quality problem occurs, replace the Developer Cartridge (toner cartridge) and the Photoconductor Unit (Drum Cartridge) first, and determine whether the problem is caused by a cartridge or caused by the printer. For a periodical print quality problem, measure the occurrence pitch of the abnormal image, and identify the abnormal component by referring to the table below. Figure 3-5.
EPSON EPL-6200/EPL-6200L Revision A 3.6.1 Blank Print or Solid Black Step Description of the problem: 4 Printed page is completely white or completely black. Action and Question Yes High voltage unit (HV1) ♦Is the connector of the High Voltage Unit (HV1) Go to Step 5 Connect properly. Problem solved Replace the high voltage unit (HV1). Replace the Main Board Assy. Replace the PH unit. connected properly? Parts that may be the source of this error PH Unit (p.
EPSON EPL-6200/EPL-6200L Revision A 3.6.2 White Out 3.6.3 Back of Paper Gets Dirty Description of the problem: Description of the problem: In the image, there are extremely light areas or areas where image is completely missing. The back side of the paper is soiled. Parts that may be the source of this error Fuser Unit (p.152) Transfer Roller (p.136) Parts that may be the source of this error Photoconductor Unit (p.135) Transfer Roller (p.136) High Voltage Unit (HV1) (p.
EPSON EPL-6200/EPL-6200L Revision A 3.6.4 Low Image Density 3.6.5 Foggy Background Description of the problem: Description of the problem: Image density is too light as a whole. Toner is present in some unexpected areas or over the whole page. Such areas appear fogged. Parts that may be the source of this error Developer Cartridge (p.135) Photoconductor Unit (p.135) Transfer Roller (p.136) High Voltage Unit (HV1) (p.
EPSON EPL-6200/EPL-6200L Revision A 3.6.6 White Stripes or White Bands 3.6.7 Black Stripes or Black Bands Description of the problem: Description of the problem: There are light or completely white bands in the printed image. These bands are running parallel with paper-feed direction over a wide area. Black stripes or bands are running parallel with the paper-feed direction. Parts that may be the source of this error Photoconductor Unit (p.135) Fuser Unit (p.
EPSON EPL-6200/EPL-6200L Revision A 3.6.8 Offset Image Description of the problem: Ghost image appears on the printed sheet. The image printed on the previous page or part of image printed on the current page appears again as a image. Parts that may be the source of this error Transfer Roller (p.136) Fuser Unit (p.152) Main Board Assy (C533/C534 Main) (p.
4 CHAPTER DISASSEMBLY AND ASSEMBLY
EPSON EPL-6200/EPL-6200L Revision A 4.1 Overview 4.1.1 Precautions This section describes procedures for disassembling the main components of the product. Unless otherwise specified, disassembly units or components can be reassembled by reversing the disassembly procedure. Things, if not strictly observed, that could result in injury or loss of life are described under the heading “Warning”. Precautions for any disassembly or assembly procedures are described under the heading “CAUTION”.
EPSON EPL-6200/EPL-6200L W A R N IN G Revision A Avant de commencer, assurez vous que l’imprimante soit eteinte et que le cordon d’alimentation soit debranche. 4.1.2 Tools Use only specified tools to avoid damaging the printer. Name C A U T IO N Use only recommended tools for disassembling, assembling or adjusting the printer. Observe the tightning torque when fixing screws. Apply lubricants and adhesives as specified. (See Chapter 6 for details.
EPSON EPL-6200/EPL-6200L Revision A 4.1.4 Main Unit Disassembly The flowchart below shows step-by-step disassembly procedure. When disassembling each component, refer to the page number shown in the figure. Paper Feed Roller (p.134) START Transfer Roller (p.136) Developer Cartridge / Photoconductor Unit Replacement (p.1 MP Cassette (MP Tray) (p.140) Paper Feed Solenoid (p.157) Left Cover (p.138) Right Cover (p.139) Cooling Fan Motor (p.155) Output Tray (p.141) Main Motor (p.
EPSON EPL-6200/EPL-6200L Revision A 4.6 Lower Cassette Unit (Option) (p.160) Paper Feed Solenoid (Lower Cassette) (p.161) Second Paper Feed Unit (p.160) Paper Feed Roller (Lower Cassette) (p.161) Paper Size Detect Switch (p.162) Paper Cassette Unit Control Board (p.162) 4.7 Duplex Unit (Option) (p.163) Right Cover (p.163) Paper Cassette Unit Control Board (p.162) Left Cover (p.163) Duplex Unit Inversion Motor (p.164) Duplex Unit Transport Motor (p.164) Duplex Unit Control Board (p.
EPSON EPL-6200/EPL-6200L Revision A 4.2 Consumables and Regular Replacement Parts 4.2.1 Locations of Fuses F101 The fuses used in this printer are as follows: (See Figure 4-1) F102: AC 125 V, 8 A F101: AC 125 V, 12 A F102 NOTE: For removal of fuses, refer to “4.3.10 Lower Rear Cover (p.144)”. 4.2.2 Paper Feed Roller 1. Remove the Imaging Cartridge. 2. Remove the Paper Feed Roller. (See Figure 4-2) Figure 4-1. Locations of Fuses Figure 4-2.
EPSON EPL-6200/EPL-6200L Revision A 4.2.3 Developer Cartridge / Photoconductor Unit Replacement C A U T IO N C H E C K P O IN T When you put the Developer Cartridge (toner cartridge) and Photoconductor Unit (Drum Cartridge) separated from each other on the floor or table, take care not to let toner fly apart. If you put the Developer Cartridge (toner cartridge) in an upright position and shake it strongly, toner may come out. Take care not to handle the Developer Cartridge in such a way.
EPSON EPL-6200/EPL-6200L Revision A 4.2.4 Transfer Roller C A U T IO N Do not touch the surface of the Transfer Roller nor stain it with chemicals or toner, for the dents or dirt on the surface of the Transfer Roller badly affects the print quality. When handling the Transfer Roller, hold the shaft of the roller or the shaft supports. Do not place any new Transfer Roller directly on the floor. 1. Remove the Imaging Cartridge. 2. Remove the Fuser Unit. (p.
EPSON EPL-6200/EPL-6200L Revision A 4.3 Removal of Covers Table 4-2. Covers No. Names Refer to 1 Paper Exit Cover p.143 2 Right Cover p.139 3 MP Cassette (MP Tray) p.140 4 Front Cover p.141 5 Top Cover p.142 6 Output Tray p.141 7 Left Cover p.138 8 Paper Exit Open/Close Cover p.142 Figure 4-6.
EPSON EPL-6200/EPL-6200L Revision A 4.3.1 Left Cover 1. Remove the screw (x1) at the rear of the printer. (See Figure 4-7) 2. Release the hook at the front bottom of the printer.(See Figure 4-8) 3. With attention paid to the two hooks at the cover top (Top Cover), lift and remove the Left Cover from the printer. (See Figure 4-7) C A U T IO N When you remove the Left Cover, be sure to release the hook shown in Figure 4-8 beforehand.
EPSON EPL-6200/EPL-6200L Revision A 4.3.2 Right Cover Screw x 1 (Rear of printer) 1. Remove the Memory Slot Cover. 2. Remove the three screws, and remove the Right Cover. (See Figure 4-9) 3. Disconnect the one connector. Screws x 2 (Rear of printer) C A U T IO N When you remove the Right Cover, be sure to release the hook shown below beforehand. The hook, if not released, can be broken during removal of the Right Cover. Figure 4-9. Right Cover Removal (EPL-6200) 1.
EPSON EPL-6200/EPL-6200L Revision A 4.3.3 MP Cassette (MP Tray) 1. While holding down the printer body with your hand, lift and remove the paper feed tray. (See Figure 4-11) 1. Close the MP Tray. 2. Remove the MP Tray while pushing one side outward. (See Figure 4-12) C H E C K P O IN T You can remove the MP Tray easily if you remove the Right and Left Covers beforehand. Figure 4-11. Removing the MP Cassette Boss x2 Figure 4-12.
EPSON EPL-6200/EPL-6200L Revision A 4.3.4 Front Cover Boss x2 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Open the Front Cover. 4. Remove the Front Cover while pushing one side inward. (See Figure 4-13) Install the Front Cover so that the Front Cover is located below the stoppers on the right and left frames of the printer. Front Cover Front Cover Figure 4-13. Front Cover Removal Stopper 4.3.5 Output Tray 1. Open the Output Tray. 2.
EPSON EPL-6200/EPL-6200L Revision A 4.3.6 Top Cover 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Open the Paper Exit Open/Close Cover. 4. Release the four hooks of the right and left printer frames. 5. Remove the Top Cover. (See Figure 4-15) 4.3.7 Paper Exit Open/Close Cover Figure 4-15. Top Cover Removal 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Remove the Top Cover. (p.142) 4.
EPSON EPL-6200/EPL-6200L Revision A 4.3.8 Paper Exit Cover 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Remove the Top Cover. (p.142) 4. Remove the Paper Exit Open/Close Cover. (p.142) 5. While pushing the right and left hooks (two hooks) at the rear of the printer inward, slide the Paper Exit Cover toward the front and remove it. (See Figure 4-17) 4.3.9 Upper Rear Cover 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Remove the Top Cover.
EPSON EPL-6200/EPL-6200L Revision A 4.3.10 Lower Rear Cover 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Remove the Top Cover. (p.142) 4. Remove the Paper Exit Cover. (p.143) 5. Remove the Upper Rear Cover. (p.143) 6. Remove the two screws securing the Lower Rear Cover, the one screw on the IF side securing the High Voltage Unit (HV1) and the two screws securing the AC Inlet. 7.
EPSON EPL-6200/EPL-6200L Revision A 4.4 Removal and Installation of Circuit Boards Control Panel W A R N IN G Disconnect the power cable before disassembling or assembling the printer. If you need to work on the printer with power applied, strictly follow the instructions in this manual. To protect sensitive microprocessors and circuitry, use static discharge equipment, such as anti-static wrist straps, when accessing internal components. Parallel I/F Board (EPL-6200) Table 4-3.
EPSON EPL-6200/EPL-6200L Revision A 4.4.1 Main Board Assy (C533/C534 Main) C A U T IO N Take care not to break the flat cable. When installing the Main Board Assy, pay attention to the orientation of the terminal side and insert the board into the inmost depth properly. 4.4.1.1 EPL-6200 (C533 Main) 1. Remove the Right Cover. (p.139) 2. Remove the three screws, and remove the protection sheet metal. (See Figure 4-21) 3.
EPSON EPL-6200/EPL-6200L Revision A 5. Disconnect all the connectors and flat cables on the Mechanical Control Board. 6. Remove the six screws, and remove the C533 Main. (See Figure 4-22) Table 4-4. Connectors CN No.
EPSON EPL-6200/EPL-6200L Revision A 4.4.1.2 EPL-6200L (C534 Main) 1. Remove the Right Cover. (p.139) 2. Remove the three screws, and remove the protection sheet metal. (See Figure 4-25) 3. Disconnect all the connectors and flat cables on the Mechanical Control Board. 4. Remove the three screws at the rear of the printer rear on the I/F side. 5. Remove the five screws, and remove the C534 Main. Table 4-5. Connectors CN No.
EPSON EPL-6200/EPL-6200L Revision A 4.4.2 Parallel I/F Board (EPL-6200) Screws x 2 1. Remove the Right Cover. (p.139) 2. Remove the three screws, and remove the protection sheet metal. (See Figure 4-21) 3. At the rear of the printer, remove the two screws on the I/F side. (See Figure 4-27) 4. Disconnect the FFC and remove the two screws, and then remove the Parallel I/F Board. Screws x 2 Connector Disconnect FFC 4.4.3 USB I/F Board (EPL-6200) 1. Remove the Right Cover. (p.139) 2.
EPSON EPL-6200/EPL-6200L Revision A 4.4.4 Control Panel 1. Remove the Right Cover. (p.139) 2. Remove the three screws, and remove the protection sheet metal and the Control Panel. (See Figure 4-29) 1. Remove the Right Cover. (p.139) 2. Remove the two screws, and remove the Control Panel Assy. (See Figure 4-30) 3. Remove the one screw, and remove the Control Panel. Figure 4-29. Control Panel Removal (EPL-6200) Figure 4-30.
EPSON EPL-6200/EPL-6200L Revision A 4.4.5 Power Supply Unit (PU1) 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Remove the Top Cover. (p.142) 4. Remove the Paper Exit Cover. (p.143) 5. Remove the Upper Rear Cover. (p.143) 6. Remove the Fuser Unit. (p.152) 7. Remove the Lower Rear Cover. (p.144) 8. Remove the four screws, and remove the Power Supply Unit (PU1) from the Lower Rear Cover. (See Figure 4-31) 4.4.6 High Voltage Unit (HV1) Figure 4-31.
EPSON EPL-6200/EPL-6200L Revision A 4.5 Removal and Installation of Major Components 4.5.1 Fuser Unit W A R N IN G The Fuser Unit remains at hazardous temperature for a certain period of time even after stop of operation and turning off of the power. To prevent suffering a burn, be sure to wait after power turning off until the temperature of the Fuser Unit cools down to a safe level, and then start working on the printer. 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3.
EPSON EPL-6200/EPL-6200L Revision A 4.5.2 Fuser Unit Disassembly C A U T IO N Do not touch the glass of the heater lamp with bare hands. When you remove the Fusing Separation Claw, take care not to lose the spring. To avoid scratching the Fusing Roller surface by the Fusing Separation Claw, keep the Fusing Separation Claw lifted when removing or installing the Fusing Roller. 1. Remove the Fuser Unit. (p.152) 2. Remove the two screws, and separate the Fuser Unit. 3.
EPSON EPL-6200/EPL-6200L Revision A 4.5.3 PH Unit W A R N IN G C A U T IO N Disconnect the power cable before disassembling or assembling the printer. Avoid exposing yourself to the laser beam to prevent injury (blindness). Do not disassemble or adjust the Print Head Unit. Otherwise, a laser beam can be emitted and you may lose your eyesight if you are exposed to the laser beam. Never touch the window at the rear of the PH Unit. A soiled window can cause image trouble.
EPSON EPL-6200/EPL-6200L Revision A 4.5.4 Main Motor 1. Remove the Left Cover. (p.138) 2. Disconnect the connector of the Main Motor. (See Figure 4-37) 3. Remove the two screws, and remove the Main Motor from the printer. 4.5.5 Cooling Fan Motor 1. Remove the Left Cover. (p.138) 2. Disconnect the connector of the Cooling Fan Motor. (See Figure 4-38) 3. Release the four hooks, and remove the Cooling Fan Motor. Figure 4-37.
EPSON EPL-6200/EPL-6200L Revision A 4.5.6 Paper Tray Empty Sensor (EPL-6200 only) 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Remove the Front Cover. (p.141) 4. Remove the protection sheet metal (Main Board). (See p.161) 5. Disconnect the one connector (CN812) on the Main Board. (See Figure 4-24 or Figure 4-25) 6. Disconnect the connector of the I/C Sensor on the Paper Feed Upper Guide Assy. (See Figure 4-39) 7.
EPSON EPL-6200/EPL-6200L Revision A 4.5.7 Paper Feed Solenoid 1. Remove the Left Cover. (p.138) 2. Disconnect the connector of the Paper Feed Solenoid. 3. Remove the one screw, and remove the Paper Feed Solenoid. After installing the solenoid, turn the gear in the direction of the arrow shown below until a click sound is made. Then the stopper of the gear is engaged with the flapper of the Paper Feed Solenoid. Flapper Gear Figure 4-41.
EPSON EPL-6200/EPL-6200L Revision A 4.5.8 Paper Feed Clutch Gear 1. Remove the Left Cover. (p.138) 2. Remove the Right Cover. (p.139) 3. Remove the Top Cover. (p.142) 4. Remove the MP Cassette (MP Tray). (p.140) 5. Remove the Front Cover. (p.141) 6. Remove the Paper Exit Cover. (p.143) 7. Remove the Fuser Unit. (p.152) 8. Remove the Power Supply Unit (PU1). (p.151) 9. Remove the Main Motor. (p.155) Figure 4-42. Removing the Push-up Plate Assy 10. Remove the Cooling Fan Motor. (p.155) 11.
EPSON EPL-6200/EPL-6200L Revision A 13. Remove the protection sheet metal. (See p.161) 14. Disconnect the one connector (CN809) and one FFC (CN805) on the Main Board. 15. Remove the two screws from each of the right and left frames of the printer, and remove the PH Base Plate Assy. (See Figure 4-43) 16. Disconnect the connector of the Paper Feed Solenoid, remove the two screws, and remove the left frame. (See Figure 4-44) 17. Remove the one screw, and remove the Paper Feed Solenoid. (See Figure 4-45) 18.
EPSON EPL-6200/EPL-6200L Revision A 4.6 Lower Cassette Unit (Option) 4.6.1 Second Paper Feed Unit 1. Remove the Duplex Unit. (If the Duplex Unit has been installed) 2. Separate the printer body and the second paper cassette from each other. 3. Release the two hooks, and remove the cover. 4. Remove the actuator. 5. Remove the six screws, disconnect the one connector, and remove the Second Paper Feed Unit. Figure 4-46.
EPSON EPL-6200/EPL-6200L Revision A 4.6.2 Paper Feed Roller (Lower Cassette) 1. Remove the Duplex Unit. (If the Duplex Unit has been installed) 2. Separate the printer body and the second paper cassette from each other. 3. Remove the two Paper Feed Rollers. 4.6.3 Paper Feed Solenoid (Lower Cassette) 1. Remove the Duplex Unit. (If the Duplex Unit has been installed) 2. Separate the printer body and the second paper cassette from each other. 3. Remove the Second Paper Feed Unit. (p.160) 4.
EPSON EPL-6200/EPL-6200L Revision A 4.6.4 Paper Cassette Unit Control Board 1. Remove the Duplex Unit. (If the Duplex Unit has been installed) 2. Separate the printer body and the second paper cassette from each other. 3. Remove the Second Paper Feed Unit. (p.160) 4. Remove the one screw, disconnect the one connector, and remove the cover. (See Figure 4-49) 5. Remove the two screws, and remove the Second Tray Control Board. Control Board Cover 4.6.5 Paper Size Detect Switch 1.
EPSON EPL-6200/EPL-6200L Revision A 4.7 Duplex Unit (Option) Left Cover 4.7.1 Right Cover 1. Remove the Duplex Unit. 2. Release the one hook. 3. Remove the Right Cover. Right Cover 4.7.2 Left Cover 1. Remove the Duplex Unit. 2. Release the one hook. 3. Remove the Left Cover. Figure 4-51. Duplex Unit 4.7.3 Duplex Unit Control Board 1. Remove the Duplex Unit. 2. Remove the Right Cover. 3. Disconnect all the connectors on the Duplex Unit Control Board. (See Figure 4-52) 4.
EPSON EPL-6200/EPL-6200L Revision A 4.7.4 Duplex Unit Inversion Motor 1. Remove the Duplex Unit. 2. Remove the Left Cover. 3. Disconnect the one connector. (See Figure 4-53) 4. Remove the two screws, and remove the Duplex Unit Inversion Motor. 4.7.5 Duplex Unit Transport Motor 1. Remove the Duplex Unit. 2. Remove the Left Cover. 3. Disconnect the one connector. (See Figure 4-54) 4. Remove the two screws, and remove the Duplex Unit Transport Motor Assy. 5.
5 CHAPTER ADJUSTMENT
EPSON EPL-6200/EPL-6200L Revision A 5.1 Overview This printer requires the following adjustments, when repairing the printer by replacing the main board. USB-ID input (See page 167) Feed Registration Adjustment (See page 169) The detailed procedures for each adjustment is explained in the following pages.
EPSON EPL-6200/EPL-6200L Revision A 5.2 USB ID Input 5.2.2 Procedure for Program Operation EPL-6200/EPL-6200L comes with the USB interface as standard, and the PC connected to the EPL-6200/EPL-6200L via the USB interface identifies the printer by referring to the USB ID information specific to each printer. C A U T IO N Monitor on Windows 95/98. Be sure to terminate the EPSON Status Monitor before starting the adjustment program.
EPSON EPL-6200/EPL-6200L 3. Revision A When the window as shown in Figure 5-2 is displayed, check “USB ID input” and click the OK button. 4. Click the OK button on the screen as shown below, and the USB ID (18 digits in total) will be written. Figure 5-2. USB ID Select Screen C H E C K P O IN T When you have selected EPL-6200L, this screen is not displayed, and the input screen as shown at right is displayed directly. Figure 5-3.
EPSON EPL-6200/EPL-6200L Revision A 5.3 Feed Registration Adjustment 5.3.2 Adjustment With the EPL-6200/6200L, the image registration position in sub-scanning direction (paper feeding direction) is adjusted on each engine mechanism and the registration position correction value is stored on the non-volatile memory on the main controller at the factory. Follow the steps below to execute the adjustment program and proceed the adjustment. C A U T IO N parallel cable to the printer.
EPSON EPL-6200/EPL-6200L Revision A Specify the port of the PC in the [Port] list box, to which the target printer is connected. As a default, “Auto Selection” is specified and the program automatically search for the port with the target printer connected. You can manually select the port by clicking [Browse] button to view all available ports. 5. Click on [OK] button and the window shouwn below is appear on the screen. 6. Click on [Print] button to print a test pattern chart.
EPSON EPL-6200/EPL-6200L C A U T IO N 7. Revision A Verify the registration position at both left and right side of the pattern. When printing a test pattern chart, make sure that the edge guide of paper tray is properly aligned against the edge of paper in order to avoid possible skew with fed paper. If the position is shifted, input the measured distance value in [Input] box and click [Input] button to store the value on the main controller.
6 CHAPTER MAINTENANCE
EPSON EPL-6200/EPL-6200L Revision A 6.1 Overview 6.1.1 Cleaning Check the inside of the printer, and remove foreign matters, if any, such as paper clips, staples, bits of paper, paper dust or toner. This section gives information necessary for maintaining the printer in its optimum condition. Table 6-1. Cleaning Items In maintenance and checks, never fail to observe the following precautions.
EPSON EPL-6200/EPL-6200L Revision A 6.1.3 Cleaning of Paper Feed Rollers PAPER FEED ROLLER OF MAIN UNIT 1. Remove the Imaging Cartridge. 2. Clean the Paper Feed Roller with a cloth. PAPER FEED ROLLER OF SECOND PAPER CASSETTE (OPTION) 1. Remove the Duplex Unit, and separate the printer body and the second paper cassette from each other. 2. Clean the Paper Feed Roller with a cloth. Figure 6-1.
7 CHAPTER APPENDIX
EPSON EPL-6200/EPL-6200L Revision A 7.1 Connectors 7.1.1 Connectors on Main Board Assy (EPL-6200) Table 7-1. Connectors on Main Board Assy (EPL-6200) CN No.
EPSON EPL-6200/EPL-6200L Revision A 7.1.2 Connectors on Main Board Assy (EPL-6200L) Table 7-2. Connectors CN No.
EPSON EPL-6200/EPL-6200L Revision A 7.1.
EPSON EPL-6200/EPL-6200L Revision A 7.2 Circuit Diagrams This section shows electric control circuit diagrams of EPL-6200/EPL-6200L. Table 7-3. Circuit Diagrams List Model Circuit Board Name Names of Parts Refer to EPL-6200 C533 MAIN Main Board Assy p.180 EPL-6200L C534 MAIN Main Board Assy p.
EPSON EPL-6200/EPL-6200L Revision A 7.3 Exploded Diagrams This section shows exploded diagrams of EPL-6200/EPL-6200L. EPL-6200 Housing (p.187) Engine Components - Fusing/Paper Exit mechanism (p.188) Engine Components - Paper Feeding mechanism (p.189) Engine Components - Drive mechanism (p.190) Electrical Components (p.191) EPL-6200L Housing (p.192) Engine Components - Fusing/Paper Exit mechanism (p.193) Engine Components - Paper Feeding mechanism (p.
C533-CASE-001 The parts to which no reference number is assigned will not be available as after-sale service parts. 05 06 08 04 07 19 3727 PWB-O 01 09 10 02 3727 38 03 21 11 37 17 23 36 32 100 25 29 27 34 35 33 30 FOR LP-2500/EPL-6200 NO.01 Rev.
C533-MECH-001 The parts to which no reference number is assigned will not be available as after-sale service parts. 03 01 46 42 09 07 05 44 45 05 12 08 06 07 08 PS3 40 06 13 39 14 H1 15 16 1305 3340 25 27 16 36 28 1305 33 1305 32 TH1 31 17 24 19 30 20 18 1305 3727 21 34 35 TS1 26 17 37 38 3727 22 29 23 FOR LP-2500/EPL-6200 NO.02 Rev.
C533-MECH-002 The parts to which no reference number is assigned will not be available as after-sale service parts. 01 10 11 07 08 06 05 09 04 13 09 14 04 S1 15 02 03 12 46 20 21 45 19 20 44 16 18 19 43 21 41 42 22 40 17 39 23 27 27 3727 36 38 SL1 24 37 26 36 28 29 25 30 PE1 35 33 31 3727 32 FOR LP-2500/EPL-6200 NO.03 Rev.
C533-MECH-003 The parts to which no reference number is assigned will not be available as after-sale service parts. 01 54 50 51 48 52 03 47 49 S2 04 05 53 07 05 46 06 44 45 08 22 42 16 40 15 09 14 18 13 19 11 20 22 3504 39 10 38 12 29 24 M1 1305 M2 27 26 36 34 3727 32 22 23 22 21 30 FOR LP-2500/EPL-6200 NO.04 32 Rev.
C533-ELEC-001 The parts to which no reference number is assigned will not be available as after-sale service parts. 4021 23 16 3504 1115 18 1115 21 22 05 07 19 100 20 3727 3504 03 3504 01 3504 3504 3727 HV1 3504 08 3547 15 14 P/H 3504 3504 PU1 3504 1318 3504 3504 09 100 12 10 13 3504 101 11 15 3504 FOR LP-2500/EPL-6200 NO.05 102 Rev.
C534-CASE-001 The parts to which no reference number is assigned will not be available as after-sale service parts. 13 20 14 15 3504 3727 PWB-O 22 16 24 12 18 100 26 29 28 30 FOR LP-1400/EPL-6200L NO.01 31 Rev.
C534-MECH-001 The parts to which no reference number is assigned will not be available as after-sale service parts. 04 02 47 43 05 05 41 06 12 10 06 PS3 13 11 39 14 H1 15 16 1305 3340 25 27 16 36 28 1305 33 1305 32 TH1 31 17 24 19 30 20 18 1305 3727 21 34 35 TS1 26 17 37 38 3727 22 23 FOR LP-1400/EPL-6200L NO.02 29 Rev.
C534-MECH-002 The parts to which no reference number is assigned will not be available as after-sale service parts. 01 10 11 07 08 06 05 09 04 13 09 14 04 S1 15 02 03 12 46 20 21 45 19 20 44 16 18 19 43 21 42 41 22 40 17 39 23 27 27 3727 36 38 SL1 24 26 36 28 29 25 30 PE1 35 31 3727 FOR LP-1400/EPL-6200L NO.03 Rev.
C534-MECH-003 The parts to which no reference number is assigned will not be available as after-sale service parts. 02 54 50 51 48 52 47 49 S2 53 07 46 17 44 45 08 22 43 16 41 15 09 14 18 13 19 11 20 22 3504 10 12 29 25 M1 1305 M2 28 26 37 35 3727 32 22 23 22 21 31 FOR LP-1400/EPL-6200L NO.04 32 Rev.
C534-ELEC-001 The parts to which no reference number is assigned will not be available as after-sale service parts. 4021 17 3504 1115 1115 06 07 100 3727 3504 04 3504 01 02 3504 3504 3727 HV1 08 3547 P/H 3504 3504 PU1 3504 3504 1318 3504 3504 09 12 10 13 3504 11 3504 FOR LP-1400/EPL-6200L NO.05 Rev.
EPSON EPL-6200/EPL-6200L Revision A 7.4 ASP List The ASP list of EPL-6200/EPL-6200Lare shown on the following page. ASP List for EPL-6200 (p.198) ASP List for EPL-6200L (p.
EPSON EPL-6200/EPL-6200L Revision A Table 7-4. ASP List - EPL-6200 EPL-6200 Ref.No. Table 7-4. ASP List - EPL-6200 Ref.No.
EPSON EPL-6200/EPL-6200L Revision A Table 7-4. ASP List - EPL-6200 Ref.No. 02-06 02-07 Table 7-4. ASP List - EPL-6200 Description Ref.No.
EPSON EPL-6200/EPL-6200L Revision A Table 7-4. ASP List - EPL-6200 Ref.No. 03-24 03-25 Table 7-4. ASP List - EPL-6200 Description Ref.No.
EPSON EPL-6200/EPL-6200L Revision A Table 7-4. ASP List - EPL-6200 Ref.No.
EPSON EPL-6200/EPL-6200L Revision A Table 7-5. ASP List - EPL-6200L EPL-6200L Description Ref.No. 01-100 "LOGO PLATE 10X40;C,2COLOR SEIKEI" 01-12 COVER 01-13 LENS 01-14 PWB ASSY 01-15 BRACKET 01-16 HARNESS 01-18 COVER 01-20 TRAY 01-22 TOP COVER 01-24 COVER 01-26 COVER 01-28 Description Ref.No. Table 7-5.
EPSON EPL-6200/EPL-6200L Revision A Table 7-5. ASP List - EPL-6200L Description Ref.No. 02-31 02-32 Table 7-5. ASP List - EPL-6200L Description Ref.No.
EPSON EPL-6200/EPL-6200L Revision A Table 7-5. ASP List - EPL-6200L Description Ref.No. 04-12 04-13 Table 7-5. ASP List - EPL-6200L Description Ref.No.
