User’s Guide NPD4384-01 EN
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Copyrights and Trademarks Copyrights and Trademarks No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer.
Contents Copyrights and Trademarks Safety Instructions Important Safety Instructions . . . . . . . . . . . . . . . . . . . . 6 Warning, Cautions, and Notes . . . . . . . . . . . . . . . . . 6 When choosing a place for this product. . . . . . . . . . 6 When setting up this product . . . . . . . . . . . . . . . . . . 6 When using this product . . . . . . . . . . . . . . . . . . . . . . 7 When handling the ink cartridges. . . . . . . . . . . . . . . 8 When transporting this product . . . . . . . . . . . . . .
Contents Print head alignment. . . . . . . . . . . . . . . . . . . . . . . . . 83 Cleaning the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Cleaning outside of the printer . . . . . . . . . . . . . . . . 85 Cleaning inside of the printer . . . . . . . . . . . . . . . . . 86 Keeping the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 If you do not use your printer for a long time. . . . 87 If you have not used your printer for more than six months . . . . . . . . . .
Contents Paper Information Paper Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Roll paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Cut sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Where To Get Help Technical Support Web Site . . . . . . . . . . . . . . . . . . . . 171 Contacting Epson Support . . . . . . . . . . . . . . . . . . . . . 171 Before Contacting Epson . . . . . . . . . . . . . . . . . . . .
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Safety Instructions Safety Instructions When choosing a place for this product O Place this product on a flat, stable surface that is larger than this product. This product will not operate properly if it is tilted or at an angle. Important Safety Instructions O Avoid places subject to rapid changes in temperature and humidity. Also keep it away from direct sunlight, strong light, or heat sources.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Safety Instructions O If you use an extension cord with this product, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cord’s ampere rating. Also, make sure the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlet’s ampere rating. When using this product O Do not put your hand inside this product or touch the ink cartridges during printing.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Safety Instructions When handling the ink cartridges O Keep ink cartridges out of the reach of children and do not drink. O If ink gets on your skin, wash it off with soap and water. If it gets in your eyes, flush them immediately with water. O Before installing the new ink cartridge in the printer, shake it back and forth horizontally in five centimeter movements about 15 times within five seconds.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Introduction Support for a range of paper types Introduction Epson offers a range of special media for ensuring high-quality printing. By selecting the right paper for the application, whether for indoor or outdoor use (lamination is recommended), you can express a whole new world of art. Also, the printer handles paper up to 1.5-mm thick and can also print on paperboard.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Introduction Borderless printing Using Auto Expand or Retain Size, you can perform borderless printing. See “Borderless printing” on page 130 There is also a borderless poster printing function that allows you to make big posters by simply joining together a number of prints.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Introduction Printer Parts Rear section Front section 1. Maintenance tanks (on both sides) The tank where the waste ink goes into. There are two maintenance tanks on both sides of Epson Stylus Pro 9890/9908. There is one maintenance tank on the right side of Epson Stylus Pro 7890/7908. 1. Adapter holder Fix the roll paper when setting the roll paper. 2. USB interface connector 2.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel 5. Paper Source button ( The Control Panel ) O Selects a paper source and roll paper cut method. The icon changes by pressing this button. However, you cannot change the paper source icon to Sheet when you set the paper while REMAINING PAPER SETUP is set to ON. Buttons, Lights, and Messages Icon You can check the ink remaining and printer status on the control panel. Buttons Explanation Roll Auto Cut On Prints on the roll paper.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel 7. Menu button ( ) Lights O Enters the Menu mode when pressed in the READY state. See “Menu Mode” on page 16 O Enters the PRINTER STATUS menu if pressed during printing. See “PRINTER STATUS” on page 24 O When pressed in the Menu mode, a desired menu can be selected. 8. OK button ( ) O Sets the selected parameter in the selected item in the Menu mode. Executes the item if the selected item is for execution only.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel 3. Platen Gap icon Display Displays the Platen Gap setting. See “Menu list” on page 19 Icon Explanation None STANDARD NARROW WIDE WIDER 1. Messages Displays the printer status, operation, and error messages. See “Error Messages on the LCD Panel” on page 90 See “Details of Menu mode” on page 21 WIDEST 2. Paper Source icon 4. Paper Number Displays the paper source and roll paper cut setting.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel O Ink remaining 6. Roll Paper Counter icon Displays the remaining amount of roll paper. When you make the following settings in ROLL PAPER REMAINING of the PAPER SETUP menu, the icon and the remaining amount of roll paper is displayed. Icon Description There is enough ink remaining. O REMAINING PAPER SETUP is set to ON. O The length of the roll paper is set for the ROLL PAPER LENGTH. Prepare a new ink cartridge.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel Menu Mode 9. Option usage icon Displays whether options are available to use or not. Option Icon Auto Take-up Reel Unit The Menu mode enables you to make printer settings similar to those you would normally make in the driver or software, as well as other additional settings, directly through the control panel.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel 1. Select a menu. 2. There are three cases depending on the items you have selected. Example: Select PRINTER SETUP. A Press the A. When you can select a parameter button to enter the Menu mode. Example: When selecting PLATEN GAP in the PRINTER SETUP menu A Press the / B Press the item. button to enter the PLATEN GAP C Press the / button to select a parameter for the item. The current setting is marked with ( ).
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel B. When you execute a function C. When you want to display the printer information Example: When selecting NOZZLE CHECK in the TEST PRINT menu Example: When selecting INK LEVEL in the PRINTER STATUS menu. A In the TEST PRINT menu, press the button to select NOZZLE CHECK. A In the PRINTER STATUS menu, press the / button to select INK LEVEL. B Press the item. button to enter the NOZZLE CHECK B Press the item.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel Menu list Menu Item Parameter “PRINTER SETUP” on page 21 PLATEN GAP NARROW, STANDARD, WIDE, WIDER, WIDEST PAGE LINE ON, OFF ROLL PAPER MARGIN DEFAULT, TOP/BOTTOM 15mm, TOP 35/BOTTOM 15mm, 3mm, 15mm PAPER SIZE CHECK ON, OFF PAPER SKEW CHECK ON, OFF REFRESH MARGIN ON, OFF AUTO NOZZLE CHECK ON: PERIODICALLY, ON: EVERY JOB, OFF PRINT NOZZLE PATTERN OFF, ON: EVERY PAGE, ON: EVERY 10 PAGES CHANGE BLACK INK MANUAL, AUTO INI
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel “PAPER SETUP” on page 25 “HEAD ALIGNMENT” on page 28 “NETWORK SETUP” on page 28 ROLL PAPER REMAINING REMAINING PAPER SETUP ROLL PAPER LENGTH ROLL LENGTH ALERT PAPER TYPE Photo Paper Proofing Paper Fine Art Paper Matte Paper Plain Paper Others CUSTOM PAPER NO PAPER SELECTED CUSTOM PAPER PAPER NO.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel Details of Menu mode PRINTER SETUP Item Parameter Explanation PLATEN GAP NARROW You can adjust the distance between the print head and paper. STANDARD O STANDARD: Normally, select STANDARD. O When selecting other than STANDARD, the following icon appears on the LCD panel.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel Item Parameter Explanation PAPER SKEW CHECK ON O ON: If the paper is not straight, an error message appears on the LCD panel and the printer stops printing. O OFF: A paper align error does not occur even if the printed data is out of range of the paper, and the printer continues to print. OFF This setting is available for roll paper only.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel TEST PRINT Item Parameter Explanation NOZZLE CHECK PRINT You can print a print head nozzle check pattern for each ink cartridge. See “Nozzle check” on page 77 STATUS SHEET PRINT You can print the current printer status. NETWORK STATUS SHEET PRINT You can print the current network status. JOB INFORMATION PRINT You can print the job information saved in the printer (up to 10 jobs.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel PRINTER STATUS This menu shows the printer status. Item Parameter Explanation VERSION JW0xxxx-xx.xx.IBCC or JN0xxxx-xx.xx.IBCC You can see the firmware version. INK LEVEL (ink color) nn% You can see the status of each ink cartridge. MAINTENANCE TANK LEFT nn% You can see the free space of the maintenance tank. RIGHT nn% JOB HISTORY No. 0 - No.9 INK xxxxx.xml PAPER xxx.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel PAPER SETUP When you use non-Epson media, be sure to make the appropriate settings for the paper. Item Parameter Explanation ROLL PAPER REMAINING REMAINING PAPER SETUP You can set the paper remaining counter function only if paper is not loaded in the printer. ROLL PAPER LENGTH ROLL LENGTH ALERT O OFF: The ROLL PAPER REMAINING function is disabled. The Roll Paper Counter icon does not appear on the LCD panel.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel CUSTOM PAPER When you use non-Epson media, you need to make settings suitable for the media. After you have selected the paper number, make the following settings. Make sure to select the paper from PAPER TYPE first, and then make the PLATEN GAP setting and so on. To set the custom paper, see the following section.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel Item Parameter Explanation PAPER FEED ADJUST PATTERN Use this setting if you are unable to resolve banding (horizontal striped lines or uneven colors) even after cleaning or aligning the print head. VALUE O Pattern This method allows you to correct by visually checking a printed pattern and entering a correction value. Check for the lightest colored pattern in lines A to D on the printed adjustment pattern.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel HEAD ALIGNMENT You can perform print head alignment. For more details, see the following section. “Print head alignment” on page 83 Item Parameter Explanation PAPER THICKNESS SELECT PAPER TYPE When using Epson special media, select the paper type. If you use non-Epson special media, enter the paper thickness in the range of 0.1 to 1.5 mm.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel OPTIONS SETUP When you use the optional equipment, set the following items. Item Parameter Explanation SpectroProofer STATUS INFORMATION In STATUS INFORMATION, displays the status of each item of SpectroProofer, such as the version of SpectroProofer, the product numbers of the white calibration tiles, the temperature of Color Measurement Device (ILS20EP), ambient air temperature, and the color of the backing.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide The Control Panel Maintenance Mode Maintenance mode list You can change the language or unit used on the display or return all the setting values to their factory default. A Turn off the printer by pressing the B Press both the button and the button at the same time to turn on the printer. Item Parameter Explanation LANGUAGE JAPANESE You can select the language to be displayed on the LCD panel. ENGLISH button.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling Paper Handling Available width for borderless printing 10 inches, 300 mm, 13 inches (Super A3), 16 inches, 17 inches, 512 mm (B2), 594 mm (A1), 24 inches (Super A1), 728 mm (B1), 36 inches (Super A0), 44 inches (Super B0) Supported Media Cut sheet We recommend you use Epson special media that can enhance the usage and expressive power of the printing results. See the following section for more information on the paper.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling Using Roll Paper C To unlock the adapter holder, push the lock lever of the adapter holder down firmly. Then move the adapter holder to the left with the handle. D Place the paper roll in the gap on the top face of the printer. Loading roll paper To load roll paper, follow the steps below.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling E G Switch the lever of the roll media adapter to fit the core size of the roll paper. Attach the roll media adapters on both ends of the roll paper. Then, pull down the lock lever of the adapters on both sides to lock. Using 2-inch core: Push the adapters into the paper core firmly. Using 3-inch core: F H Release the lock lever of the adapters on both sides.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling I K Slide the adapter holder with the handle to make the left roll media adapter align with on the adapter holder. Slide the adapter holder with the handle to the right to set it in the holder axis firmly. Make sure to set both ends of the roll paper into the adapters firmly. J Roll the roll paper slowly into the roll paper holder. 34 L Push the lock lever of the adapter holder up to lock. M Press the button.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling N P Insert the paper into the insertion slot. Pull the paper down through the paper insertion slot so that it comes out below. Press the button. Take care not to fold the edge of the paper, and insert it so that there is no slack. If you have difficulty feeding the paper, adjust the paper suction by pressing the or button. Pull the paper to fit the edge of the paper to the label position.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling Cutting the roll paper after printing Cutting the roll paper Cutting the roll paper automatically There are two ways to cut the roll paper. Method Operation Auto cut Cut the roll paper after printing each page automatically. Manual cut Cut the roll paper manually, or cut the roll paper using cutter sold at a store. Cut the roll paper automatically after printing each page.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling C Removing the roll paper Make sure the printer is turned on. B Open the roll paper cover. button to release the paper The roll paper is rewound automatically if the printer state is after the paper cut but in the READY state. However, when using the optional Auto Take-up Reel Unit, the printer does not rewind the roll paper.Rewind the roll paper manually, if it is not automatically done.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling D E F To unlock the adapter holder, push the lock lever of the adapter holder down firmly. Move the adapter holder to the left with the handle until the end. Then take it off from the holder axis. Pull up the lock lever of the adapter to unlock. Then remove the roll media adapter from the paper roll. After rewinding the roll paper carefully, place it in the original bag that it came in when you purchased it.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling Using Cut Sheet Media Loading cut sheet smaller than A3 size The procedures differ depending on your paper size and thickness. Paper Refer to Smaller than A3 size “Loading cut sheet smaller than A3 size” on page 39 A3 or larger or thick paper “Loading cut sheet A3 size or larger / thick paper” on page 40 Note: O Flatten the paper before loading it in the printer.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling D Load the sheet into the paper insertion slot until it meets resistance. Loading cut sheet A3 size or larger / thick paper Align the right edge of the paper with the setting position, and then insert the paper until it meets resistance. When using paper sizes A4 or below, set the paper until it reaches the bottom along the line on the metal part under the paper insertion slot. PRESS THE BUTTON appears on the LCD panel.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling E H Load the sheet into the paper insertion slot. If ARE THESE SETTINGS OK? appears on the LCD panel, press the or button to select NO and then press the button. Set the media type and paper remaining, and then press the button to set the media. The previous setting appears on the LCD panel. If the media type and paper remaining are correct, select YES and then press the button.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling B Ejecting Paper Press the button to remove the paper. This section explains how to eject paper after printing. Note: When you use the paper basket, see the following section. “Using the paper basket and paper guides” on page 43 When you use optional Auto Take-up Reel Unit, see the following section.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling When feeding paper forward Using the paper basket and paper guides The paper guides keep the ejected prints straight. This section explains how to switch the status from feeding paper backward to feeding paper forward. To avoid your prints getting dirty or crinkled, set the paper basket as explained below. The feeding direction is different depending on the media type.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling C When feeding paper backward Slightly tilt the front paper basket to set the paper guides to the horizontal position. Feed the prints backward and store them in the paper basket. This section explains how to switch the status from feeding paper forward to feeding paper backward. Note: Do not stack more than one print in the paper basket. If you stack multiple prints, the space between the paper supports and paper basket becomes narrow.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling C Move the paper guides to the vertical position, and then bring the front basket back as far as it goes. If the paper is A1 or smaller: Lift both the front and rear baskets as shown below. D Bring the front paper basket up and fasten it with the hook-and-loop fastener straps. If the paper is larger than A1 size: Tilt the rear basket until parallel to the floor during printing. Be sure to fasten the hook-and-loop fastener upward.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling Storing the paper basket Note: When printing on Enhanced Matte Paper, you can stack plural prints on the front basket by tilting it until parallel to the floor. The quality of the prints may not be assured, including scratches or dirty appearing. If the paper basket is not used, bring the front basket up to the vertical position. This section explains how to switch the status from feeding paper backward status to storing paper basket.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling C Remove the hook-and-loop fastener straps, and refasten it downward. Then bring the front paper basket up to the vertical position. Using Auto Take-up Reel Unit (For Epson Stylus Pro 9890/9908 only) When you want to print your data on roll paper and do not want to cut it or feed it out onto the floor, you can use the optional Auto Take-up Reel Unit to roll up your print. You can wind the roll paper forward or backward.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling Control box Winding paper forward A Plug the power cord into an outlet, and make sure the sensor light is on. B Turn on the printer by pressing the C Make sure the Auto Take-up Reel Unit icon is displayed on the LCD panel. 1. Sensor light Displays the status of the Auto Take-up Reel Unit. Light Status On It is ready to use. Flashing rapidly It is operating. Flashing slowly It is in the power-saving mode.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling G Winding paper backward Tape the leading edge of the roll paper to the take-up reel core in three places. A Turn on the printer, and then pull out the roll paper. See step 3 to 6 of the following section. “Winding paper forward” on page 48 H Press the button to feed the paper forward and create a loop of slack.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling Taking up your prints Removing paper after take-up When the Auto Take-up Reel Unit is installed, and the take-up reel core is loaded with paper to take up in the desired direction, you can use the unit to take up your prints. After paper take-up, follow the steps below to remove the take-up reel core. A Set the Auto switch to Off. B Cut the roll paper. w Warning: Do not touch the Auto Take-up Reel Unit while it is operating.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling D Remove the take-up reel core from the flange knob on the movable unit and the drive unit. Using the core from a used paper roll as a take-up reel core Caution: The paper roll is heavy so have two people hold it by both ends of the paper roll. You can use a used paper roll as the take-up reel core. c Note: If the paper roll core is deformed or damaged, it cannot be used as a take-up reel core.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling C D Installing a take-up reel core Remove the flange by pinching the knob. The method of installing the take-up reel unit is the same for both 2-inch and 3-inch reel cores. A Make sure that the lock lever is released (turned to the left). Slide the movable unit to the left end of the horizontal strut. B Slip one end of the take-up reel core over the flanged knob on the drive unit.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling D Turn the lock lever to the front to lock the movable unit. Printable area Make sure the take-up reel unit is locked properly and firmly. A B-L B-R C Roll paper The minimum top margin is 3.0 mm (0.12") Cut sheets The minimum top margin is 3.0 mm (0.12") Roll paper The minimum left margin is 0.0 mm (0") Cut sheets The minimum left margin is 0.0 mm (0") Roll paper The minimum right margin is 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Handling Parameter A B-L B-R C TOP/ BOTTOM 15mm 15mm 3mm 3mm 15mm TOP35/ BOTTOM 15mm 35mm 3mm 3mm 15mm 15mm 15mm 15mm 15mm 15mm 3mm 3mm 3mm 3mm 3mm Note: O The print area does not change even when the margins are changed. O The printer automatically detects the dimensions of the paper that is loaded. Print data that exceeds the printable area of the paper cannot be printed.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Basic Settings Making the printer driver settings Basic Settings A Print Settings Turn on the printer, and set the paper in the printer. See “Paper Handling” on page 31 This section describes how to print your data from an application using the Epson printer driver. Printing procedures (Windows) B From the File menu, select Print or Page Setup. C Make sure your printer is selected, and click Printer, Setup, Options, Properties, or Preferences.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Basic Settings E Select the paper source and paper size according to the paper loaded in the printer. Printing procedures (Mac OS X) A After making the settings, click OK. Make sure to select the same paper size as you set in the application. Turn on the printer, and load the paper. See “Using Cut Sheet Media” on page 39 See “Loading roll paper” on page 32 F Click Print.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Basic Settings E Note: When using Mac OS X 10.4, or if items on the Page Setup screen are not displayed on the Print screen due to the application being used in Mac OS X 10.7, 10.6. or 10.5, follow the steps below to display the Page Setup screen. Select Print Settings from the list, and then set each item. From the File menu of the application, click Page Setup. D Check that this printer is selected, and then set the paper size.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Basic Settings Selecting the paper size Roll paper Cut sheet Paper Size *XXXX is the paper size. Explanation XXXX Roll Paper - Banner Select this size when using a banner printing application. This prints no margins on the top and bottom and a 3-mm margin on the right and left sides. XXXX Roll Paper - Borderless (Auto Expand) Select this size when performing borderless printing on the roll paper.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Basic Settings Checking the printer status When problem occurs during printing For Windows The Progress Meter appears on your display when you start printing. It indicates the progress of the current print job and provides printer status information such as ink remaining and product number of the ink cartridges. Also, you can cancel a print job using Progress Meter.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Basic Settings Canceling Printing Canceling printing using the computer (Windows) There are a few ways to stop the print operation depending on the situation. When Progress Meter is displayed Click Stop on the EPSON Progress Meter dialog box. While sending data Cancel using computer Cancel using printer Operation ✓ - Select the data that you want to cancel using the computer.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Basic Settings Changing the Black Ink Canceling printing using the computer (Mac OS X) A Click the Printer icon in the Dock. B Select the job you want to delete, and then click the Delete button. Both Photo and Matte Black ink are installed in this printer. Photo Black ink can be used for photo papers with professional quality results. Matte Black ink significantly increases black optical density when printing on matte and fine art type papers.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Basic Settings B Open the Main menu (Windows) or the Print Settings dialog (Mac OS X). C After selecting the paper type from Media Type, select the black ink you want to use. When the paper selected in Media Type is only designed for a certain type of black ink, you cannot change the type of black ink. Select the type of black ink that supports the paper in advance from the printer's control panel.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Options and Consumable Products Options and Consumable Products The following consumable products are available for use with your printer (as of August, 2010). For the latest information, see the Epson Web site. Name Product Code Epson special media See the following section for media.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Options and Consumable Products Name Product Code Explanation Auto Take-up Reel Unit (for Epson Stylus Pro 9890/9908) C12C815321 Auto Take-up Reel Unit is for Epson Stylus Pro 9890/9908 only. You cannot use with Epson Stylus Pro 7890/7908. See the Auto Take-up Reel Unit Setup Guide for installing it. See the following section to use Auto Take-up Reel Unit.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Maintenance Notes for when you are not using the printer The print head nozzles are very small, thus, they can become clogged easily if dust gets on the print head. To avoid this, close the roll paper cover or the front cover when you are not using the printer. If you are not using the printer for a long time, put a non-static cloth on the printer to avoid getting dust on the printer.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Notes for storing the paper O Do not lose the paper package so you can use it for storing the paper. See the instructions below and the handling instructions of the paper for more details. Notes for after printing O Avoid locations that are subject to direct sunlight, excessive heat, or moisture. See the instructions below for after printing. O Do not touch the surface of the print; otherwise, the ink may smudge.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Replacing Ink Cartridges Mac OS X Note: When you replace the ink cartridges while the printer is turned off, the remaining ink cannot be detected correctly so the ink may become unusable before the Ink Check light comes on and you cannot print correctly. Follow the steps below to replace an ink cartridge.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Using the printer driver Note: In the Monitoring Preferences dialog box, select the Shortcut Icon check box to display a shortcut icon on your Windows taskbar. Right-click the shortcut icon, and select the printer name to display the EPSON Status Monitor 3 dialog box. See “Summary of the Utility Tab” on page 116 You can check the amount of ink remaining on your computer by using EPSON Status Monitor.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance About ink cartridges O Do not drop or knock it against hard objects; otherwise, the ink may leak. Be sure to use the ink cartridges that are supported with this printer. See “Options and Consumable Products” on page 63 O Although nothing may be printed, the printer uses ink from all cartridges during head cleaning and other maintenance operations to keep the print heads in good condition.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance O Avoid getting dirt on the ink system port and store the ink cartridge properly. You do not need to put the ink cartridge in the package. The ink system port has a valve in it so you do not need to put a cap on it; however, be careful not to tamper with the ink system port. Replacing ink cartridges A Make sure the printer is on. B Press the button. Note: The button is not available while printing or cleaning.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance E H Push the expended cartridge so the cartridge is slightly pushed out. Hold the ink cartridge with the arrow mark facing up and pointing to the rear of the printer, and then insert it into the slot as far as it will go until it clicks. Match the ink cartridge color with the color label on the back side of the ink cover. F Carefully pull the expended cartridge straight out of the slot. Note: Be sure to install all nine ink cartridges.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Replacing the Maintenance Tank Replacing the maintenance tank Be sure to use a maintenance tank that is supported with this printer. See “Options and Consumable Products” on page 63 The maintenance tank absorbs ink discharged when cleaning the print head. There are two maintenance tanks placed on the left and right for Epson Stylus Pro 9890/9908 and one placed on the right for Epson Stylus Pro 7890/7908.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance E Replacing the Cutter Insert the new maintenance tank into place as far as it will go. When the paper cutter does not cut cleanly, it may be dull and require replacement. See the following section for the product code of the paper cutter that is supported with this printer. See “Options and Consumable Products” on page 63 c Caution: Take care not to damage the cutter blade.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance E Press the F If the optional SpectroProofer Mounter is attached to the printer, remove it from the printer and then turn off the printer. button. The paper cutter holder stops at the replacement position. H Screw down the cutter with a screwdriver. I Carefully remove the old cutter from the printer.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance K O Screw up the cutter firmly with a cross head screwdriver. Note: Screw up the cutter firmly, otherwise the cut position may be slightly shifted or skewed. L Align the downside of the cover and the cutter holder, and then press the cover firmly until it clicks. M Install the SpectroProofer Mounter if it was attached, and then turn the printer on. The cutter holder moves to the home position.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Adjusting the Print Head You may need to adjust the print head if white lines appear in your printed data or if you notice the print quality has declined. You can perform the following printer maintenance functions for maintaining the print head in consistently good condition to ensure the best print quality. Manual cleaning function You can perform cleaning manually according to the print quality.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Nozzle check Checking the print head nozzles using the printer driver This function checks the print head*1 nozzles*2 for clogging by printing a nozzle check pattern. Perform head cleaning if you find that the nozzle check pattern is unexpectedly faint or has missing dots in the nozzle check pattern. This section explains how to check the print head nozzle using the Window printer driver. Use Epson Printer Utility 4 for Mac OS X.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Checking the print head nozzles using the printer’s control panel A Good Make sure that roll paper or A4/Letter size or larger is loaded in the printer. Select the correct paper source according to the paper. See “Paper Handling” on page 31 B Press the C Press the / button to display TEST PRINT, and then press the button. D Press the / button to display NOZZLE CHECK, and then press the button.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Head cleaning Cleaning the print head using the printer driver If you find that the printed data is unexpectedly faint or dots in the printed data are missing, you may be able to solve these problems by using the Head Cleaning utility to clean the print head, which ensures that the nozzles are delivering ink properly. This section explains how to clean the print head using the Window printer driver. Use Epson Printer Utility 4 for Mac OS X.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance D Click Print Nozzle Check Pattern in the Head Cleaning dialog box. Cleaning the print head using the printer’s control panel Confirm the nozzle check pattern. A Press and hold the B Press the / button to display MAINTENANCE, and then press the C Press the / button to display CLEANING, and then press the button. D Press the / button to display NORMAL CLEANING, and then press the button. See “Nozzle check” on page 77 button.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance E Press the button. Power cleaning If the nozzles are still clogged after performing head cleaning a few times, perform power cleaning. The Power light starts flashing and the head cleaning starts (it takes 2 to 13 minutes.) The cleaning is finished when the Power light is on. F Print a nozzle check pattern, and check the result.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Capping function Automatic maintenance function Capping is a function for automatically covering the print head with a cap (lid) to prevent the print head from drying out. Capping is performed in the following situations. This printer has a self-cleaning function and capping function for maintaining the print head in consistently good condition to ensure the best print quality.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Aligning the print head using the control panel Print head alignment To prevent deterioration of print quality caused by misalignment of the print head, align the print head before you start printing your data. Select AUTO to correct any head misalignment automatically to obtain optimum printing results. If you select MANUAL, you need to check the pattern and enter the value for alignment.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Aligning the print head manually To align the print head, see either of the following section. “Aligning the print head automatically” on page 84 “Aligning the print head manually” on page 84 Because there is a distance between the print head and paper, the misalignment may occur by the humidity or temperature or moving the print head bidirectionally. In this case, try UNI-D first, and then BI-D 2-COLOR.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance If you are not satisfied with the result of this alignment, see the next section to try BI-D ALL. Cleaning the Printer After you set the patterns, press the button to return to the READY state. To keep your printer in top operating condition, clean it thoroughly if it becomes soiled.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance C Cleaning inside of the printer If the print gets a scratch or smudge, follow the steps below to wipe off the smudge inside of the printer. Wipe the gray part by following the directions of the arrows. If there is a serious problem of dirt on the inside of the printer, clean it using a soft, clean cloth dampened with a mild detergent. Then, wipe the inside of the printer with a dry, soft cloth.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance E Keeping the Printer If some powdery paper dust is accumulated on the platen, use something like a toothpick to remove it. When storing the printer, place it on a horizontal surface with the ink cartridges installed in the printer. c Caution: The printer must be kept flat. Do not tilt it, stand it on end, or turn it upside down.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Transporting the Printer If you have not used your printer for more than six months When transporting the printer, repack the printer using the original box and packing materials to protect from shock and vibration. O When activating AUTO NOZZLE CHECK in the panel settings, the printer checks the print head nozzles for clogging, and performs print head cleaning automatically if needed.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Maintenance Transporting the printer Setting up the printer after transporting When you transport the printer, be sure to repack the printer using the original box and packing materials. The steps you need to take to set up the printer after transporting it are almost identical to the steps carried out the first time you set up the printer. When you set up the printer again, refer to the Setup Guide.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Problem Solver Error Messages on the LCD Panel Error messages Messages are either status messages or error messages. Many common printer problems can be identified by the lights and messages on the LCD panel. See the following messages to solve problems. Error messages related to paper Error messages Description What to do PAPER OUT LOAD PAPER No paper is loaded in the printer. Load paper correctly.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Error messages Description What to do PAPER ERROR LOAD PAPER CORRECTLY REFER TO THE MANUAL The paper is not loaded correctly. Press the button to release the paper presser, and remove the paper. Then, set the paper correctly. See “Using Roll Paper” on page 32 See “Using Cut Sheet Media” on page 39 PAPER SENSOR ERROR PRESS THE BUTTON LOAD DIFFERENT PAPER The barcode has not been read correctly.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Error messages related to the printer Error messages Description What to do FRONT COVER OPEN CLOSE FRONT COVER The front cover is open. Close the front cover. INK COVER OPEN CLOSE RIGHT AND LEFT INK COVERS The ink cover(s) is open. Close the ink cover(s). The ink cover(s) cannot be opened. Remove any object if it is obstructing the ink cover(s). Then, press the button again.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Error messages related to the maintenance Error messages Description What to do PAPER SENSOR ERROR PRESS THE BUTTON LOAD THE CORRECT PAPER REFER TO THE MANUAL The loaded paper is not proper for the Print Head Alignment. Press the button to clear the error. Press the button to release the paper presser, and then load the paper that matches with the media type selected for the Print Head Alignment.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Error messages Description What to do INK CARTRIDGE ERROR REPLACE CARTRIDGE The ink cartridge was found faulty. There may be a bad contact or dew condensation in the cartridge. O Remove the ink cartridge and reinstall it. If this message appears after reinstalling the ink cartridge, replace it with a new one. (Do not reinstall the ink cartridge that caused an error.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Error messages Description What to do INK CARTRIDGE NON-GENUINE CARTRIDGE! QUALITY OF NON-GENUINE INK MAY VARY Non-genuine ink cartridge is installed. Select DECLINE to replace the ink cartridge with a genuine Epson ink cartridge. Selecting ACCEPT may void EPSON’s warranty. See “About ink cartridges” on page 69 See “Replacing ink cartridges” on page 70 NON-GENUINE CARTRIDGE MAY NOT PERFORM AT OPTIMUM.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Error messages Description What to do TAKE-UP ERROR IS ANYTHING OBSTRUCTING THE TAKE-UP REEL SENSOR SYSTEM? LOAD PAPER AGAIN The Auto Take-up Reel Unit does not wind the paper. Make sure there is no obstruction in the sensor system. Press the button to release the paper presser, and then set the paper correctly in the Auto Take-up Reel Unit.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Error messages Description What to do SpectroProofer ERROR REFER TO THE MANUAL TO FIND OUT HOW TO SOLVE THE PROBLEM NN Error No. 01 Turn the printer off, and then remove the SpectroProofer from the printer. Connect the SpectroProofer to the printer properly, and then turn on the printer. The SpectroProofer is not connected to the printer properly.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Error messages Description What to do SpectroProofer ERROR REFER TO THE MANUAL TO FIND OUT HOW TO SOLVE THE PROBLEM NN Error No. 80 Turn off the printer, and then remove the color measurement device and the white calibration tile from the SpectroProofer mounter.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver When the maintenance request occurs A maintenance request warns you to replace the consumables with a new one very soon. If MAINTENANCE REQUEST NNNN is displayed on the LCD panel, contact your dealer and tell them the maintenance request code. If you continue to use the printer, the service call error occurs.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Troubleshooting You cannot print (because the printer does not work) Cause What to do The printer does not turn on. Is the power cord plugged into the electrical outlet or the printer? Make sure the power cord is securely plugged into the printer. Is there any problem with the electrical outlet? Make sure your outlet works by trying to connect the power cord of another electric product.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Cause What to do The printer is not correctly connected to the computer. Is the cable plugged properly? Make sure the printer’s interface cable is securely plugged into the correct terminal of the computer. Also, make sure the cable is not broken nor bent. If you have a spare cable, try with the spare cable.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Cause What to do The printer stops printing. Is the status of print queue "paused"? (Windows) If you stop printing or the printer stops printing because of some troubles, the status of print queue becomes "paused". You cannot print in this condition. Double-click the printer icon in the Printers folder, and select Pause Printing from the Printer menu to clear the check box.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver The printer sounds like it is printing, but nothing prints Cause What to do The ink cartridges may have a problem. If the print head moves, but nothing prints, confirm the printer operation. Print a nozzle check pattern. You can check the printer’s operation and status without connecting the printer to the computer. See “Nozzle check” on page 77 If the nozzle check pattern has missing dots, perform a print head cleaning.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver The prints are not what you expected Cause What to do Print quality is poor, uneven, too light, or too dark. Are the print head nozzles clogged? If the nozzles are clogged, the print quality is reduced. Print the nozzle check pattern.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Cause What to do Print quality is poor, uneven, too light, or too dark. Have you compared the printing result with the image on the display monitor? Since monitors and printers produce colors differently, printed colors will not always match on-screen colors perfectly. O Televisions and monitors produce a range of colors by combining the 3 colors known as the 3 primary colors of light, red (R), green (G), and blue (B).
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Cause What to do The print is not positioned properly on the paper. Have you specified the print area? Check the print area in the settings of the application and printer. Is the paper size setting correct? If the Paper Size setting and the size of the actual paper do not match, the print may not be where you want it, or part of it may be cut off. In this case, check the print settings.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Cause What to do Too much ink is being released. Is the Media Type setting correct? Make sure that the paper settings of the printer match the paper that you are using. The discharge of ink is controlled in accordance with the media type. If you print on plain paper using the photo paper setting, too much ink will be discharged for the type of paper.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Feeding or ejecting troubles Cause What to do Unable to feed or eject paper. Is the paper loaded in the right position? Refer to the following for the correct position to load the paper. See “Paper Handling” on page 31 If the paper is loaded correctly, check the condition of the paper that you are using. Is the paper loaded vertically? Single sheets should always be loaded vertically.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Cause What to do The paper is jammed. To remove jammed paper, follow the steps below: 1. If roll paper is jammed, open the roll paper cover and cut the paper at the paper insertion slot. 2. Make sure that the Pause light is not flashing, and then press the the paper presser. 3. Rewind the roll paper.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Cause What to do The paper is jammed 4. Open the front cover if the paper is jammed inside the printer. Caution: Be careful not to touch the cables around the print head; otherwise, the printer may be damaged. 5. Carefully remove the jammed paper. Be careful not to touch the roller, ink absorption, and ink tubes inside the printer. 6. Close the front cover, and then turn the printer off and back on.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Problem Solver Other troubles Cause What to do Color ink runs out quickly even when printing in the Advanced B&W Photo mode or when printing black data. Color ink is consumed in print head cleaning. When print head cleaning is performed, all nozzles are cleaned so that the ink for all colors is consumed. (Even when Advanced B&W Photo mode is selected, the ink for all colors is consumed during cleaning.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Windows) For Windows XP Click Start, Control Panel, Printers and Other Hardware, and then Printers and Faxes. Using the Printer Driver (Windows) Note: If your Windows XP Control Panel is in Classic View, click Start, Control Panel, and then Printers and Faxes. B Displaying the Settings Screen Right-click your printer icon, and click Printing preferences.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Windows) Displaying Help Right-click on the item you want to check and display You can access the printer driver help in the following ways: Right-click the item, and then click Help. O Click Help O Right-click on the item you want to check Click the Help Button to Display By displaying help, you can use the contents page or keyword search to read the help.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Windows) Customizing the Printer Driver You can save up to 100 settings. You can choose a setting you have registered from the Select Settings list box. Note: You can save the settings as a file by clicking Export. You can share the settings by clicking Import to import the saved file on another computer. You can save the settings or change the display items as you prefer.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Windows) C Enter any name in the Name box, and then click Save. You can save up to 100 settings. You can choose a setting you have registered from the Media Type list box. B Select Edit Item. C Order or group items in the List box. Note: You can save the settings as a file by clicking Export. You can share the settings by clicking Import to import the saved file on another computer.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Windows) Summary of the Utility Tab EPSON Status Monitor 3 You can check the printer's status, such as the remaining ink level and error messages, from the computer's screen. You can perform the following maintenance functions from the printer driver's Utility tab.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Windows) Uninstalling the printer driver Menu Arrangement You can arrange display items, Select Setting, Media Type, and Paper Size, for example, you can reorder them by the frequency of your access. See “Rearranging display items” on page 115 Follow the steps below to remove the printer driver and EPSON LFP Remote Panel 2. Export or Import You can export or import the printer driver settings.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Windows) D Select the target printer icon, and then click OK. Note: You can also remove Epson Network Utility by clicking the Utility tab and selecting the Epson Network Utility. However, if you are using other Epson printer(s), their printer driver(s) may also be using the Epson Network Utility. If you are using other Epson printer(s), do not remove Epson Network Utility. E Follow the on-screen instructions to continue.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Mac OS X) Using Epson Printer Utility 4 Using the Printer Driver (Mac OS X) You can perform maintenance tasks such as Nozzle Check or Head Cleaning by using Epson Printer Utility 4. This utility is installed automatically when you install the printer driver.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Mac OS X) Uninstalling the printer driver EPSON Status Monitor You can check the printer's status, such as the remaining ink level and error messages, from the computer's screen. Follow the steps below to remove the printer driver and EPSON LFP Remote Panel 2. Note: You must log in with an Administrator account. A Turn off the printer, and unplug the interface cable. B Close all open applications.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Using the Printer Driver (Mac OS X) G Double-click the Printer folder and then the Driver folder. Note: If the folder does not appear, double-click the EPSON icon on the desktop. K Select Uninstall, and then click Uninstall. L Follow the on-screen instructions to continue. Removing EPSON LFP Remote Panel 2 Delete EPSON LFP Remote Panel 2 by deleting the EPSON LFP Remote Panel 2 folder. See the EPSON LFP Remote Panel 2 help for details.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Printing Varieties Auto Correct Color and Print Photos (PhotoEnhance) OS Color Management Settings Windows XP (other than the above) No Color Management In other applications, set No Color Management.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties C On the PhotoEnhance screen, you can set effects to apply to the print data. Correct color and print See the printer driver help for more details on each item. The printer driver automatically and internally corrects colors to match the color space. You can select from the following color correction modes. O Charts and Graphs Performs color correction to sharpen your images based on the sRGB space.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties OS Color Management Settings Windows 7 Printer Manages Colors B When the printer driver's Main screen is displayed, select the color correction mode. See “Print Settings” on page 55 Windows Vista To perform automatic color correction, select Automatic and then select the color correction mode. Windows XP (Service Pack 2 or later and .NET 3.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties D Check other settings, and then start printing. B Display the Print screen. C For Mac OS X 10.7, 10.6 and 10.5, select Color Matching from the list, and then click EPSON Color Controls. Making Settings for Mac OS X A When using applications featuring a color management function, specify how to adjust colors from these applications. When using applications without a color management function, start from step 2.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties D Display the Advanced Color Settings screen for color correction. E Make the necessary settings. F Check other settings, and then start printing. Select Print Settings from the list, and select EPSON Standard (sRGB) or Charts and Graphs, from Color Controls in Color Settings. When adjusting the parameters manually, click Advanced Color Settings. Note: When using the following applications with Mac OS X 10.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Printing Black and White Photos Select Color Management and then Document. Select Printer Manages Colors or No Color Management as the Color Handling setting, and then click Print. You can print black and white photos with rich gradation by adjusting the image data color by the printer driver. The original data is not affected. You can correct image data when printing without processing the data from applications.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties C Select Custom as the Mode setting, and then click Advanced. OS Color Management Settings Mac OS X 10.7, 10.6 and 10.5 Printer Manages Colors Mac OS X 10.4 No Color Management In other applications, set No Color Management. Example of Adobe Photoshop CS4 Open the Print screen. D Make the necessary settings. E Check other settings, and then start printing. Select Color Management and then Document.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties B Display the Print screen, select Print Settings from the list, and then select Advanced B&W Photo as the Color. D Make the necessary settings. E Check other settings, and then start printing. See the printer driver help for more details on each item. See “Printing procedures (Mac OS X)” on page 56 Note: When using the following applications with Mac OS X 10.5, clear the Use Generic RGB checkbox.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Borderless printing - Match the paper size and page setting for the print data. You can print your data without margins on the paper. - If the application has margin settings, set the margins to 0 mm. The types of borderless printing you can choose vary as shown below depending on the media type. - Make the image data as large as the paper size.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Supported Media Sizes for Borderless Printing The following media sizes are supported for borderless printing. Paper widths 254 mm/10 inch 300 mm 329 mm/13 inch/Super A3 406 mm/16 inch 432 mm/17 inch 515 mm/B2 594 mm/A1 610 mm/24 inch/Super A1 728 mm/B1* 914 mm/36 inch/Super A0* 1118 mm/44 inch/Super B0* * Epson Stylus Pro 7890/7908 does not support these size.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties About Roll Paper Cutting When performing borderless printing on roll paper, you can specify whether it is left and right borderless printing or all edges borderless printing, and how to cut the paper in the printer driver's Roll Paper Option. The cutting operation for each value is shown in the following chart. Printer driver settings Normal Cut Single Cut Double Cut The default printer driver setting is Normal Cut.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties C Setting Procedures for Printing Making Settings in Windows A When the printer driver's Main screen is displayed, you can configure various settings required for printing such as Media Type, Source, Page Size. See “Print Settings” on page 55 B Select Auto Expand or Retain Size as the Method of Enlargement. If you select Auto Expand, set how much of the image goes beyond the edge of the paper as shown below.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties XXXX (Roll Paper - Borderless (Auto Expand)) XXXX (Roll Paper - Borderless (Retain Size)) XXXX (Sheet - Borderless (Auto Expand)) XXXX (Sheet - Borderless (Retain Size)) Where XXXX is the actual paper size, such as A4. Max : 3 mm for left and 5 mm for right (the image shifts 1 mm to the right) Standard : 3 mm for left and right Min : 1.5 mm for left and right When using Mac OS X 10.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties D Enlarged/Reduced Printing Select Print Settings from the list, and then set the Media Type. You can enlarge or reduce the size of your data. There are three setting methods. O Fit to Page printing Automatically enlarges or reduces the image size to fit the paper size. E Check other settings, and then start printing.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Making Settings for Mac OS X Fit to Page/Scale to fit paper size A Making Settings in Windows A When the printer driver's Page Layout screen is displayed, set the same paper size as the data's paper size in Page Size or Paper Size. Open the Print screen, select Paper Handling from the list, and then check Scale to fit paper size. See “Printing procedures (Mac OS X)” on page 56 For Mac OS X 10.7, 10.6, or 10.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Fit to Roll Paper Width (Windows only) A C Select the width of the roll paper loaded in the printer from the Roll Width list. D Check other settings, and then start printing. When the printer driver's Page Layout screen is displayed, set the same paper size as the data's paper size in Page Size or Paper Size.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties C B Select Reduce/Enlarge, click Custom, and then set the Scale to value. Enter a value directly or click the arrows to the right of the scale box to set the value. Set the scale in Scale. If Scale is not displayed on the Print screen, open the Page Setup screen, and then make the settings. Select the scale within a range of 10 to 650 %. You can now print as normal. D Check other settings, and then start printing.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Multi-Page Printing Making Settings in Windows A You can print multiple pages of your document on one sheet of paper. See “Print Settings” on page 55 If you print continuous data prepared at A4 size, it is printed as shown below. Note: O In Windows, you cannot use the Multi-Page printing function when performing borderless printing.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Poster Printing (Enlarge to cover several sheets and print - Windows only) Making Settings for Mac OS X A When the Print screen is displayed, select Layout from the list, and then specify the number of pages per sheet and so on. See “Printing procedures (Mac OS X)” on page 56 The poster printing function automatically enlarges and divides the print data. You can join the printed sheets to create a large poster or calendar.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties image joins fit precisely. Setting Procedures for Printing A Prepare the print data using applications. B When the printer driver's Page Layout screen is displayed, select the Multi-Page check box, select Poster, and then click Settings. C In the Poster Settings screen, select the number of pages you want in the poster.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties When with margins is selected: Clear Borderless Poster Print. Joining the output paper together The steps for joining the output paper together differ between borderless poster printing and poster printing with margins. Borderless poster printing This section describes how to join four printed pages together. Check and match the printed pages, and join them in the order indicated below using an adhesive tape on the back of the sheets.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Note: The alignment marks are black for black-and-white printing. C While two pages are overlapping, cut them along the alignment mark (vertical red line). D Join the left and right sheets together. E Repeat steps 1 to 4 for the lower sheets. F Cut the bottom of the upper sheets along the alignment marks (horizontal blue line). Use an adhesive tape to stick the backs of the sheets together.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties G Lay the upper sheet on top of the lower sheet. Lineup the X marks as shown in the illustration below, and temporarily fasten them using an adhesive tape on the back. H While two pages are overlapping, cut them along the alignment marks (horizontal red line). I Join the upper and lower sheets together. J Use an adhesive tape to stick the backs of the sheets together.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Printing on custom paper Making Settings in Windows A You can also print on paper sizes that are not already available in the printer driver. If you create and save a user-defined paper size using the steps below, you can select the saved paper size from Page Setup in the application.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Note: O To change the paper size you saved, select the paper size name from the list on the left. C O To delete the user-defined size you saved, select the paper size name from the list on the left, and then click Delete. O You can save up to 100 paper sizes. Click +, and then enter the paper size name. C Enter the Width, Height for the Paper Size, and enter the margins, and then click OK. Click OK.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Banner printing (on roll paper) Note: O To change the contents that you saved, select the paper size name from the list on the left of the Custom Paper Sizes screen. D O To duplicate the user-defined size you saved, select the paper size name from the list on the left of the Custom Paper Sizes screen, and then click Duplicate.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Available Media Sizes Width Epson Stylus Pro 9890/9908: 89 to 1118 mm Epson Stylus Pro 7890/7908: 89 to 610 mm Length* Windows: Max. 15000 mm Note: O You can only use Roll Paper (Banner) for applications that support banner printing. O Mac OS X: Max. 15240 mm * The paper length can be longer if using applications that support banner printing.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties F Select the size of the data created by the application from the Page Size list, and select the roll paper width loaded in the printer for the Roll Width or Output Paper. Making Settings for Mac OS X A When the Print screen is displayed, select the size of the data created with the application in Paper Size. When using Mac OS X 10.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties B Layout Manager (Windows only) Make settings in Scale to enlarge the size of the document you created in your application to the size of the paper you want to print on. If Scale is not displayed on the Print screen, open the Page Setup screen, and then make the settings. The Layout Manager function allows you to place multiple pieces of print data created in different applications on the paper freely and print them at once.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties Placing the same data Setting Procedures for Printing A Check that the printer is connected and ready to print. B Open the file you want to print in your application. C In the printer driver's Main screen, select Layout Manager, and select the size of the document made in the application as the Size. See “Print Settings” on page 55 Placing data freely Note: The Size set here is used on the Layout Manager screen.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Printing Varieties F Arrange the objects on the Layout Manager screen. Saving and Calling Layout Manager Settings You can drag objects to move and resize them, use tool buttons and the Objects menu to align and rotate objects on the Layout Manager screen. You can save the Layout Manager screen arrangement and setting contents to a file.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Color Management Printing Color Management Print Settings Color Management Printing You can perform color management printing using this printer's printer driver in the following two ways. About Color Management Choose the best method according to the application you are using, the operating system environment, the aim of the print out and so on.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Color Management Printing Setting color management with the application Setting profiles Settings for the input profile, printer profile, and intent (matching method) vary between three types of color management printing since their color management engines are used differently. This is because color management usage differs between the engines. Make settings in the printer driver or application as described in the following table.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Color Management Printing C Setting color management with the printer driver Set color management to off. For Windows In the Main screen, select Custom as the Mode setting, and select Off (No Color Adjustment). Color management printing by Host ICM (Windows) Use image data in which an input profile has been embedded. Also, the application must support ICM. A Make the settings for color adjustment using the application.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Color Management Printing Select Color Management and then Document. Select Printer Manages Colors as the Color Handling setting, and then click Print. To change the profile, select Show all profiles at the bottom. D Color management printing by ColorSync (Mac OS X) When using applications without a color management function, start from step 2. B Check other settings, and then start printing.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Color Management Printing D Furthermore, in Mac OS X 10.5 select Print Settings from the list, and then select Off (No Color Adjustment) from Color Settings. Select Color Management and then Document. Select Printer Manages Colors as the Color Handling setting, and then click Print. B For Mac OS X 10.4 A Display the Print screen, select Print Settings from the list, and then select ColorSync as the Color Settings.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Color Management Printing Select Color Management and then Document. Select Printer Manages Colors as the Color Handling setting, and then click Print. Color management printing by Driver ICM (Windows only) The printer driver uses its own printer profiles to perform color management. You can use the following two color correction methods. O Driver ICM (Basic) Specify one type of profile and intent for processing the entire image data.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Color Management Printing C Intent Explanation Saturation Keeps the current saturation unchanged and converts the data. Perceptual Converts the data so that a more visually natural image is produced. This feature is used when a wider gamut of color is used for image data.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Paper Information Paper Information Epson offers specially designed media for ink jet printers to meet most high-quality printing needs. Item Explanation Media name Describes the media name. Size Describes the paper size for cut sheet media and the width for roll paper. Borderless Describes whether borderless printing is available. Recommended: The recommended paper for borderless printing.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Roll paper Premium Glossy Photo Paper (250) Size 406 mm 16" 610 mm 24" 914 mm * 36" * 1118 mm * 44" * ICC profile Photo Black Matte Black Pro9890_9908_7890_7908 PremiumGlossyPhoto Paper250.icc — Borderless Thickness Core diameter Recommended 0.27 mm 3" Media type of the printer driver Auto Cut Photo Paper Premium Glossy Photo Paper (250) Y Borderless Thickness Core diameter Recommended 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Premium Luster Photo Paper (260) Size Borderless Thickness Core diameter Recommended 0.27 mm 3" 254 mm 10" 300 mm 12" 406 mm 16" 508 mm 20" Impossible 610 mm 24" Recommended 914 mm * 36" * 1118 mm * 44" * ICC profile Photo Black Matte Black Pro9890_9908_7890_7908 PremiumLusterPhoto Paper260.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Premium Glossy Photo Paper (170) Size Borderless Thickness Core diameter 420 mm (A2) Impossible 0.18 mm 2" 610 mm 24" 914 mm * 36" * 1118 mm * 44" * Recommended ICC profile Media type of the printer driver Auto Cut Photo Paper Premium Glossy Photo Paper (170) Y Size Borderless Thickness Core diameter 420 mm (A2) Impossible 0.18 mm 2" Photo Black Matte Black Pro9890_9908_7890_7908 PremiumGlossyPhoto Paper170.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Epson Proofing Paper Publication Size 330 mm 13" 432 mm 17" 610 mm 24" 914 mm * 36" * 1118 mm * 44" * ICC profile Photo Black Matte Black Pro9890_9908_7890_7908 EpsonProofingPaper Publication.icc — Borderless Thickness Core diameter Possible 0.20 mm 3" Media type of the printer driver Auto Cut Proofing Paper Epson Proofing Paper Publication Y Borderless Thickness Core diameter Possible 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Enhanced Adhesive Synthetic Paper Size 610 mm 24" 1118 mm * 44" * ICC profile Photo Black Matte Black — Pro9890_9908_7890_7908 EnhancedAdhesive SyntheticPaper.icc Borderless Thickness Core diameter Possible 0.17 mm 2" Media type of the printer driver Auto Cut Others Enhanced Adhesive Synthetic Paper Y Borderless Thickness Core diameter Recommended 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Singleweight Matte Paper Size 432 mm 17" 610 mm 24" 914 mm * 36" * 1118 mm * 44" * ICC profile Photo Black Matte Black — Pro9890_9908_7890_7908 SingleweightMatte Paper.icc Borderless Thickness Core diameter Recommended 0.14 mm 2" Media type of the printer driver Auto Cut Matte Paper Singleweight Matte Paper Y Borderless Thickness Core diameter Possible 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Textured Fine Art Paper Size 432 mm 17" 610 mm 24" 914 mm * 36" * 1118 mm * 44" * ICC profile Photo Black Matte Black Pro9890_9908_7890_7908 TexturedFineArtPaper_PK.ic c Pro9890_9908_7890_7908 TexturedFineArtPaper_MK.ic c Borderless Thickness Core diameter Possible 0.37 mm 3" Media type of the printer driver Auto Cut Fine Art Paper Textured Fine Art Paper Y Borderless Thickness Core diameter Possible 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Cut sheet Premium Glossy Photo Paper Size Borderless Thickness Super A3/B Possible 0.27 mm A2 Impossible ICC profile Media type of the printer driver Photo Black Matte Black Photo Paper Premium Glossy Photo Paper Pro9890_9908_7890_7908 PremiumGlossyPhoto Paper.icc — Size Borderless Thickness Super A3/B Possible 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information Archival Matte Paper/Enhanced Matte Paper Size Borderless Thickness Super A3/B Possible 0.26 mm A2 Impossible ICC profile Media type of the printer driver Photo Black Matte Black Matte Paper Pro9890_9908_7890_7908 ArchivalMattePaper_PK.icc Pro9890_9908_7890_7908 ArchivalMattePaper_MK.icc Archival Matte Paper Enhanced Matte Paper Photo Quality Inkjet Paper Size Borderless Thickness Super A3/B Possible 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Paper Information UltraSmooth Fine Art Paper Size Borderless Thickness Super A3 Possible 0.46 mm A2 Impossible ICC profile Media type of the printer driver Photo Black Matte Black Fine Art Paper Pro9890_9908_7890_7908 UltraSmoothFineArtPaper_PK. icc Pro9890_9908_7890_7908 UltraSmoothFineArtPaper_M K.icc UltraSmooth Fine Art Paper Velvet Fine Art Paper Size Borderless Thickness Super A3/B Possible 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Where To Get Help Contacting Epson Support Where To Get Help New :See comments to select sections you need. The word "other" indicates products except for inkjet, SPC, Page, and SIDM. New :For All products Technical Support Web Site Before Contacting Epson If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting information in your product documentation, contact Epson support services for assistance.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Where To Get Help Help for Users in North America Help for Users in Europe Epson provides the technical support services listed below. Check your Pan-European Warranty Document for information on how to contact Epson support. New :Use Inkjet, SPC, and "other" products Only.(general) Internet Support Help for Users in Taiwan Visit Epson’s support website at http://epson.com/support and select your product for solutions to common problems.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Where To Get Help Internet URL http://www.epson.com.au Telephone number Fax number Address 03-2810606 03-2810707 No.413, Huannan Rd., Pingzhen City, Taoyuan County 324, Taiwan 03-5325077 03-5320092 1F., No.9, Ln. 379, Sec. 1, Jingguo Rd., North Dist., Hsinchu City 300, Taiwan 04-23291388 04-23291338 3F., No.510, Yingcai Rd., West Dist., Taichung City 403, Taiwan 04-23805000 04-23806000 No.530, Sec. 4, Henan Rd., Nantun Dist.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Where To Get Help O Sales enquiries and product information O Frequently Asked Questions (FAQ), Sales Enquiries, questions through e-mail O Product usage questions or problems Epson Hotline O Enquiries on repair service and warranty O Sales enquiries and product information Help for Users in Thailand O Technical support Contacts for information, support, and services are: New :For all products World Wide Web (http://www.epson.co.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Where To Get Help Internet Home Page O Enquiries on repair services & warranty, product usage and technical support (Techline) Epson Hong Kong has established a local home page in both Chinese and English on the Internet to provide users with the following information: Phone: O Product information 603-56288333 Help for Users in India O Answers to Frequently Asked Questions (FAQs) Contacts for information, support, and services are: New :For all pro
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Where To Get Help Help for Users in the Philippines To obtain technical support as well as other after sales services, users are welcome to contact the Epson Philippines Corporation at the telephone and fax numbers and e-mail address below: New :For All products Trunk Line: (63-2) 706 2609 Fax: (63-2) 706 2665 Helpdesk Direct Line: (63-2) 706 2625 E-mail: epchelpdesk@epc.epson.com.ph World Wide Web (http://www.epson.com.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Product Information Printer Specifications Product Information Printing System Requirements for the Printer Driver Your computer should meet the following system requirements to use the printer driver: Printing method On-demand ink jet Nozzle configuration Black: 360 nozzles × 3 (Photo Black / Matte Black, Light Black, Light Light Black) Color: 360 nozzles × 5 (Cyan, Vivid Magenta, Light Cyan, Vivid Light Magenta, Yellow) System requirements Window
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Product Information Electrical Resolution Maximum 2880 × 1440 dpi Print direction Bidirectional Control code ESC/P2, ESC/P3 Rated voltage AC 100-240 V RAM 256 MB for Main 65 MB for Network Input voltage range AC 90 to 264 V Character tables PC 437 (US, Standard Europe) 50 to 60 Hz Character sets EPSON Courier 10 cpi Rated frequency range Input frequency range 49.5 to 60.5 Hz Rated current Epson Stylus Pro 9890/9908: 1.0 to 0.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Product Information Ink cartridges Colors Note: O The ink cartridges packaged with your printer are partly used during initial setup. In order to produce high-quality prints, the print head in your printer will be fully charged with ink. This one-off process consumes a quantity of ink and therefore these cartridges may print fewer pages compared to subsequent ink cartridges.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Product Information Environmental Temperature Humidity Standards and Approvals Operation 10 to 35ºC (50 to 95ºF) Safety UL 60950-1 Print Quality Guarantee 15 to 25ºC (59 to 77ºF) Storage -20 to 40ºC (-4 to 104ºF) Operation 20 to 80% RH* CAN/CSA-CEI/IEC CISPR 22 Class B Print Quality Guarantee 40 to 60% RH* AS/NZS CISPR 22 Class B Storage 5 to 85% RH** EMC Directive 2004/108/EC CAN/CSA C22.2 No.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Product Information Interface Your printer is equipped with a USB interface and an Ethernet interface. USB interface Hi-Speed USB - Compatible with the USB 2.0 Specification. Ethernet interface The printer has a built-in Ethernet interface. Use a 10BASE-T, 100BASE-TX STP (shielded twisted-pair) cable via the RJ-45 connector to connect to a network.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Software License Terms Software License Terms New :change template (2clm -> 1clm) Open Source Software Licenses Bonjour This printer product includes the open source software programs which apply the Apple Public Source License Version1.2 or its latest version ("Bonjour Programs"). We provide the source code of the Bonjour Programs pursuant to the Apple Public Source License Version1.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Software License Terms 1.4 "Externally Deploy" means: (a) to sublicense, distribute or otherwise make Covered Code available, directly or indirectly, to anyone other than You; and/or (b) to use Covered Code, alone or as part of a Larger Work, in any way to provide a service, including but not limited to delivery of content, through electronic communication with a client other than You. 1.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Software License Terms 2.2 Modified Code. You may modify Covered Code and use, reproduce, display, perform, internally distribute within Your organization, and Externally Deploy Your Modifications and Covered Code, for commercial or non-commercial purposes, provided that in each instance You also meet all of these conditions: (a) You must satisfy all the conditions of Section 2.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Software License Terms 6. Additional Terms. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations and/or other rights consistent with the scope of the license granted herein ("Additional Terms") to one or more recipients of Covered Code. However, You may do so only on Your own behalf and as Your sole responsibility, and not on behalf of Apple or any Contributor.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Software License Terms 10. Trademarks. This License does not grant any rights to use the trademarks or trade names "Apple", "Apple Computer", "Mac", "Mac OS", "QuickTime", "QuickTime Streaming Server" or any other trademarks, service marks, logos or trade names belonging to Apple (collectively "Apple Marks") or to any trademark, service mark, logo or trade name belonging to any Contributor.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Software License Terms 13.2 Relationship of Parties. This License will not be construed as creating an agency, partnership, joint venture or any other form of legal association between or among You, Apple or any Contributor, and You will not represent to the contrary, whether expressly, by implication, appearance or otherwise. 13.3 Independent Development.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Software License Terms The Original Code and all software distributed under the License are distributed on an 'AS IS' basis, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND APPLE HEREBY DISCLAIMS ALL SUCH WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT OR NON-INFRINGEMENT.
Epson Stylus Pro 9890/9908/7890/7908 User’s Guide Software License Terms 4. Info-ZIP retains the right to use the names “Info-ZIP,” “Zip,” “UnZip,” “UnZipSFX,” “WiZ,” “Pocket UnZip,” “Pocket Zip,” and “MacZip” for its own source and binary releases.
